SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
10th Edition
ISBN: 9781260163155
Author: BUDYNAS
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 1, Problem 9P
A cylindrical part of diameter d is loaded by an axial force P. This causes a stress of P/A. where A = πd2/4. If the load is known with an uncertainty of ±10 percent, the diameter is known within ±5 percent (tolerances), and the stress that causes failure (strength) is known within ±15 percent, determine the minimum design factor that will guarantee that the part will not fail.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Prob # 1.A round bar made from SAE 1025 low Carbon steel is to support a direct tension load of 50,000 lbs. Using a factor of safety of 4, and assuming that the stress concentration factor, k = 1, What is the suitable standard diameter. Yield stress is 40,000 psi.
a. 3 ½ inch
b. 2 ¼ inch
c. 2 9/16 inch
d. 1 ½ inch
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size.
Round your answer to 4 significant figures
Determine the width and thickness of the leaves (in mm) of a leaf spring using the following specifications:
Total load = 140 kN;
Number of springs supporting the load = 4; Maximum number of leaves = 10;
Span of the spring = 1000 mm;
Permissible deflection = 80 mm;
Modulus of elasticity, E = 200 kN/mm2;
and allowable stress in spring material is 600 MPa.
Chapter 1 Solutions
SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select a mechanical component from Part 3 of this...Ch. 1 - Select an organization listed in Sec. 16, go to...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Go to the Internet and connect to the NSPE website...Ch. 1 - Estimate how many times more expensive it is to...Ch. 1 - The costs to manufacture a part using methods A...Ch. 1 - A cylindrical part of diameter d is loaded by an...Ch. 1 - When one knows the true values x1 and x2 and has...Ch. 1 - Use the true values x1 = 7 and x2 = 8 (a)...
Ch. 1 - A solid circular rod of diameter d undergoes a...Ch. 1 - A fatigue test is performed on rotating beam...Ch. 1 - Determinations of the ultimate tensile strength...Ch. 1 - The lives of parts are often expressed as the...Ch. 1 - The tensile 0.2 percent offset yield strength of...Ch. 1 - A mechanical system comprises three subsystems in...Ch. 1 - From See. 3-12, the maximum shear stress in a...Ch. 1 - A round cold-drawn 1045 steel rod has a mean...Ch. 1 - A beam subjected to axial loading will experience...Ch. 1 - Three blocks A, B, and C and a grooved block D...Ch. 1 - The volume of a rectangular parallelepiped is...Ch. 1 - A pivot in a linkage has a pin in the figure whose...Ch. 1 - A circular cross section O ring has the dimensions...Ch. 1 - Prob. 25PCh. 1 - Prob. 26PCh. 1 - Prob. 27PCh. 1 - Prob. 28PCh. 1 - Convert the following to appropriate ips units:...Ch. 1 - Convert the following to appropriate SI units: (a)...Ch. 1 - Generally, final design results are rounded to or...Ch. 1 - Repeal Prob. 1-31 for the following: (a) = F/wt,...Ch. 1 - Repeat Prob. 131 for: (a) = F/A, where A = d2/4, F...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A hard-drawn steel wire extension spring has a wire diameter of 4mm, an outside coil diameter of 28 mm, and initial tension of 1200 N is applied to the spring. The spring shows an extension of 85 mm. The approximate number of turns is 25. From the given information: Determine the physical parameters of the spring such as mean diameter, spring index, maximum shear stress, total number of turns, Wahl’s stress factor, free length of the spring, and pitch of the coilarrow_forwardA plate made of steel 20C8 (Sut = 440 N/mm2 ) in hot rolled and normalized condition is shown in Fig. It is subjected to a completely reversed load of 30 kN. The notch sensitivity factor q can be taken as 0.8 and the expected reliability is 90%. The size factor is 0.85. The factor of safety is 2. Determine the plate thickness for infinite life. (V. B. Bhandari Example 5.3)arrow_forwardCompute the relative change in resistance, ΔR/R, if a piezoresistive device experiences stress of 20 MPa in one direction. Use a value of 3.84 GPa for Young's modulus of the piezoresistive material. Express your answer in three decimal places.arrow_forward
- Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading conditions according to the Maximum shear stress hypothesis and the Maximum strain energy hypothesis. Shaft diameter: 20 mm, Shaft Length 120 mm, F1 = 750N, F2 = 3000N, Mb = 2400 N.mm. Steel if St37 and Safety coefficient is 2 If taken, will this stick work safely under these operating conditions? (Yield of given steel Strength 225 Mpa, Tensile strength 370 Mpa)arrow_forwardA strain gauge mounted at a potentially critical point in a steel part has recorded the stress history shown below during 20 seconds of typical use. Identical parts have been fatigue tested under constant amplitude loading with R = -1 to give an endurance limit of 60 ksi and a fatigue strength of 140 ksi at N = 1000 cycles. The steel used has an ultimate strength of 165 ksi. Estimate the fatigue life of the part under typical use. How much will the fatigue life in problem 3 (above) be reduced if a mean stress of 10 ksi is added to the stress history given?arrow_forwardA bar is subjected to a combination of a steady load of 60kN and a load fluctuating between - 10kN and 90 kN. The corrected endurance limit of the bar is 150 MPa, the yield strength of the material is 480 MPa and the ultimate strength of the material is 600MPa. The bar cross-section is square with side a. If the factor of safety is 2, the value of a (in mm), according to the modified Goodman‟s criterion, is ____arrow_forward
- Sintered silicon nitride parts are expected to experience tensile stresses 50% of the ultimate tensile strength of the material. What will be the maximum allowable size of internal flaws for these parts not to fail in service? Given the following properties of the material: Specific surface energy: 0.3 J/m2 its Youngs Modulus: 304 GPa Ultimate tensile Strength: 570 MPa Select one: a. 1.43 µm b. 0.71 µm c. 15 µm d. 85 µm e. 9.5 µmarrow_forwardA) An engineer works for a company that has many gray cast iron rods of different diameters and would like to design an equivalent rod that could handle a force of P= 10.0 kipkip without fracturing. What is the minimum diameter that this new rod must have to support P? B)A tensile test is being conducted on a steel-rod specimen with a gauge length of L0 = 4.0 in and an initial diameter of d0 = 0.75 in. If the final length of the rod at fracture is Lf= 5.53 in , find the percent elongation of the rod at fracture.arrow_forwardCompute the minimum vine diameter to provide a desired factor of safety of 1.7 against yield-type failure. Assume a yield stress of 300 MPa, and that the mass of the monkey is 65 kg. Hint Weight (N) = Mass (Kg) X g (9.81 m/s2)arrow_forward
- A resistance, wire strain gauge with a gauge factor of 3 is bonded to a steel structural e subjected to a stress of 200 MN/m² The modulus of elasticity of steel is 400 GN/m² Calculate the % change in the value of the gauge resistance due to the applied stressarrow_forwardAt a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine(a) the lowest temperature at which the two bars contact each other.(b) the normal stress in the two bars at a temperature of 260°F.(c) the normal strain in the two bars at 260°F.(d) the change in width of the aluminum bar at a temperature of 260°F.arrow_forwardAt a temperature of 60°F, a 0.03-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.70 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.9 in. and a thickness of 0.70 in. The supports at A and C are rigid. Assume h1=3.0 in., h2=1.9 in., L1=27 in., L2=47 in., and Δ=Δ= 0.03 in. Determine:arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY