EBK MATERIALS FOR CIVIL AND CONSTRUCTIO
4th Edition
ISBN: 8220102719569
Author: ZANIEWSKI
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 10, Problem 10.25QP
A pine wood specimen was prepared with actual dimensions of 50 mm × 50 mm × 250 mm and grain parallel to its length. The deformation was measured over a gauge length of 200 mm. The specimen was subjected to compression parallel to the grain to failure. The load–deformation results are as shown in Table P10.25.
TABLE P10.25
Load (Kn) | Deformation (mm) |
0 | 0 |
8.9 | 0.457 |
17.8 | 0.597 |
26.7 | 0.724 |
35.6 | 0.838 |
44.5 | 0.965 |
53.4 | 1.118 |
62.3 | 1.270 |
71.2 | 1.422 |
80.1 | 1.588 |
89.0 | 1.765 |
97.9 | 1.956 |
106.8 | 2.159 |
111.3 | 2.311 |
- a. Using a computer spreadsheet program, plot the stress–strain relationship.
- b. Calculate the modulus of elasticity.
- c. What is the failure stress?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A pine wood specimen was prepared with actual dimensions of 50 mm ×
50 mm x 250 mm and grain parallel to its length. The deformation was meas-
ured over a gauge length of 200 mm. The specimen was subjected to compres-
sion parallel to the grain to failure. The load-deformation results are as shown
in Table P10.25.
TABLE P10.25
Load (Kn)
Deformation (mm)
8.9
0.457
17.8
0.597
26.7
0.724
35.6
0.838
44.5
0.965
53.4
1.118
62.3
1.270
71.2
1.422
80.1
1.588
89.0
1.765
97.9
1.956
106.8
2.159
111.3
2.311
a. Using a computer spreadsheet program, plot the stress-strain
relationship.
b. Calculate the modulus of elasticity.
c. What is the failure stress?
A pine wood specimen was prepared with actual dimensions of 50 mmx50 mm x 250 mm and grain
parallel to its length. The deformation was measured over a gauge length of 200 mm. The specimen
was subjected to compression parallel to the grain failure. The load- deformation results are shown in
table below:
Load (kN)
Deformation (mm)
8.9
0.457
17.8
0.597
26.7
0.724
34.5
0.838
43
0.965
52.9
1.118
62.01
1.27
71.03
1.422
80.1
1.588
89
1.765
99.6
1.956
108
2.159
111.3
2.311
112
2.456
a. Using a computer spreadsheet program, plot the stress-strain relationship.
b. Calculate the modulus of elasticity.
С.
What is the failure stress?
Pls answer thanks
Chapter 10 Solutions
EBK MATERIALS FOR CIVIL AND CONSTRUCTIO
Ch. 10 - What are the two main classes of wood? What is the...Ch. 10 - Prob. 10.2QPCh. 10 - Prob. 10.3QPCh. 10 - Discuss the anisotropic nature of wood. How does...Ch. 10 - Prob. 10.5QPCh. 10 - Prob. 10.6QPCh. 10 - Prob. 10.7QPCh. 10 - Prob. 10.8QPCh. 10 - Prob. 10.9QPCh. 10 - Prob. 10.10QP
Ch. 10 - Prob. 10.11QPCh. 10 - Prob. 10.12QPCh. 10 - Prob. 10.13QPCh. 10 - Prob. 10.14QPCh. 10 - Prob. 10.15QPCh. 10 - Prob. 10.16QPCh. 10 - Prob. 10.17QPCh. 10 - Prob. 10.18QPCh. 10 - Prob. 10.19QPCh. 10 - Prob. 10.20QPCh. 10 - Prob. 10.21QPCh. 10 - Prob. 10.22QPCh. 10 - Prob. 10.23QPCh. 10 - A wood specimen was prepared with actual...Ch. 10 - A pine wood specimen was prepared with actual...Ch. 10 - Prob. 10.26QPCh. 10 - Prob. 10.27QPCh. 10 - Prob. 10.28QPCh. 10 - Prob. 10.29QPCh. 10 - Prob. 10.30QPCh. 10 - Prob. 10.31QPCh. 10 - Prob. 10.32QPCh. 10 - Prob. 10.33QP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poison's ratio is 0.25 than the change in volume of the cylindrical piece is?arrow_forwardA wood beam is strengthened using two steel plates as shown in the figure below. *Inserted Photo* The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. Calculate the maximum tensile and compressive stresses of the beam. Assume that Ew = 11 GPa and Es = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood ? MPa maximum tensile stress in steel ? MPa maximum compressive stress in wood ? MPa maximum compressive stress in steel ? MPaarrow_forwardPlease answer complete questionarrow_forward
- 3. Reproduce the table from NSCP 2015 showing the values of strength reduction phi under different conditions of strain in steel.arrow_forwardThe composite material is fastened to their junction at rigid plate B and attached to rigid fixed supports at both ends subjected to two loads of 12k positioned symmetrically at B. Determine the stresses and their corresponding behavior for each material. Use 2 decimal places in every solved value. 亚 А 12k 12k 1 ft Steel Est = 29 x 10° psi Ast = 1.03 in? B Aluminum 2 ft Eal = 10 × 106 psi Aal = 8.92 in² Carrow_forwardGive correct handwritten answerarrow_forward
- Solve botharrow_forwardA wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 232 mm 38 mm 6.5 mm 163 mm- The beam has a cross section of dimensions 150 mm x 232 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 46 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN • m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) kN marrow_forwardWhat is the maximum diameter of aggregate considering the clear spacing of the reinforcements in mm? 160mm slab Slab=10mm 130mm beam 700mm 17.25cm 500mm 4 Obeam=25mm D =?arrow_forward
- The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 250 N . (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate units. µA Value Units Figure 1 of 1 Submit Request Answer Part B 300 mm Determine the shear stress that acts parallel to the grains. 60 mm Express your answer to three significant figures and include the appropriate units. 20° 25 mm HẢ ? Value Units P Pearsonarrow_forward2. An aluminum alloy specimen with a radius of 0.28 in. was subjected to tension until fracture and produced results shown in Table P4.3. Table P4.3 Stress, ksi Strain, 10 ° in./in. 0.0 8 0.6 17 1.5 27 2.4 3.2 35 43 4.0 4.6 50 58 5.2 62 5.8 64 6.2 65 6.5 67 7.3 68 8.1 9.7 a. Using a spreadsheet program, plot the stress-strain relationship. b. Calculate the modulus of elasticity of the aluminum alloy. c. Determine the proportional limit. d. What is the maximum load if the stress in the bar is not to exceed the proportional limit? e. Determine the 0.2% offset yield strength. f. Determine the tensile strength. g. Determine the percent of elongation at failure.arrow_forwardProblem 6arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning
Choosing Architectural Materials; Author: 30X40 Design Workshop;https://www.youtube.com/watch?v=dcbgDFpfScY;License: Standard Youtube License