Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 10, Problem 10RQ
What is the difference between tolerance and allowance?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Round off to 3 significant figures, and the tolerance is ±1 in the 3rd significant digit. Thank you.
Which type of feature doesn't belong to form tolerances?
a)The profile of a surface
b)Circularity
c)Cilindricity
d)Flatness
a) Name two groups of standards in addition to national, industry-wide standards and where they are valid.
b) Which three options exist for defining dimensional tolerances in a technical drawing?
Chapter 10 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 10 - What are some of the advantages to the consumer of...Ch. 10 - DFMÂ stands for design for manufacturing. Why is...Ch. 10 - Explain the difference between attributes and...Ch. 10 - Prob. 4RQCh. 10 - What are the four basic measures upon which all...Ch. 10 - What are gage blocks?Ch. 10 - Why do gage blocks come in sets?Ch. 10 - Prob. 8RQCh. 10 - What is the difference between accuracy and...Ch. 10 - What is the difference between tolerance and...
Ch. 10 - Prob. 11RQCh. 10 - Prob. 12RQCh. 10 - Why might you use a shrink fit to join the wheels...Ch. 10 - Explain the difference between repeatability and...Ch. 10 - When measuring time, is it more important to be...Ch. 10 - Prob. 16RQCh. 10 - What factors should be considered in selecting...Ch. 10 - Prob. 18RQCh. 10 - What is parallax? (Why do linesmen in tennis sit...Ch. 10 - Explain the rule of 10 in terms of tolerances.Ch. 10 - How does the vernier caliper work to make...Ch. 10 - What are the two most likely sources of error in...Ch. 10 - What is the major disadvantage of a micrometer...Ch. 10 - What is the main advantage of a micrometer over...Ch. 10 - What is the major difficulty in obtaining an...Ch. 10 - Why is the toolmakers microscope particularly...Ch. 10 - What are the ways that linear measurements can be...Ch. 10 - What type of instrument would you select for...Ch. 10 - What are the chief disadvantages of using a vision...Ch. 10 - What is a CMM (coordinate measuring machine)?Ch. 10 - Prob. 31RQCh. 10 - How can the no�go member of a plug gage be...Ch. 10 - What is the primary precaution that should be...Ch. 10 - What tolerances are added to gages when they are...Ch. 10 - Explain how a go/no�go ring gage works to check...Ch. 10 - Why are air gages particularly well suited for...Ch. 10 - Explain the principle of measurement by...Ch. 10 - How does a toolmakers flat differ from an optical...Ch. 10 - Prob. 1PCh. 10 - Read the 25�division vernier graduated in metric...Ch. 10 - In Figure 10.C , the sleeve�thimble region of...Ch. 10 - Suppose that in Figure 10.31 the height of the...Ch. 10 - What is the estimated error in this measurement,...Ch. 10 - Figure 10.D shows the sleeve�thimble region of...Ch. 10 - In Figure 10.E , two examples of a metric...Ch. 10 - Prob. 8PCh. 10 - Figure 10.F shows a section of a vernier...Ch. 10 - Here is a table that provides a description of...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Determine the moment reactions at the supports A and B. El is constant.
Mechanics of Materials
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
A large Darrieus vertical axis wind turbine was built by the U.S. Department of Energy near Sandia, New Mexico...
Fox and McDonald's Introduction to Fluid Mechanics
ICA 8-38
An ideal gas is kept in a 10-liter [L] container at a pressure of 1.5 atmospheres [atm] and a temperat...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
A flagpole with attached light triangular frame is shown here for an arbitrary position during its raising. The...
Engineering Mechanics: Statics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which type of feature doesn't belong to orientation tolerances? Concentricity Angularity Perpendicularity Parallelismarrow_forwardWhat other geometric tolerance is automatically controlled when parallelism is applied to a surface? Position. Symmetry. Flatness. Profile.arrow_forwardTell us about the tolerance zone in operations.arrow_forward
- What is a transfer-type measuring tool?arrow_forwardhow do you write this in a feature control frame? "The cross-sectional shape of this feature must be round within a radial tolerance zone of .002"arrow_forwardWhich method of tolerancing does not exist? a)Limit tolerance b)Triolateral tolerance c)Bilateral tolerance d)Unilateril tolerancearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
LIMITS FITS AND TOLERANCES: What is limit fit & tolerance and its need? Animation; Author: ADTW learn;https://www.youtube.com/watch?v=joBy4BoJszo;License: Standard YouTube License, CC-BY
Limits and Continuity; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=9brk313DjV8;License: Standard YouTube License, CC-BY