PROGRAMMABLE LOGIC CONTROLLERS BUNDLE
5th Edition
ISBN: 9781260582475
Author: Petruzella
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 10, Problem 16RQ
Program Plan Intro
Data manipulation instructions:
- Data manipulation instructions enable the numerical data that exists in the controller’s memory to be performed within the control program.
- Data manipulation instructions allows manipulation of data that is stored in either single or multiple words groups.
- It also includes the transfer of data from one data memory area of the Programmable Logic Controller (PLC) to another.
- In order to accomplish data manipulation, there are mainly two different kinds of instructions.
- Instructions which operate on word data.
- Instructions which operate on file or block.
- It also provides great flexibility to program control circuits.
Explanation of Solution
b.
Converting decimal number into binary value:
- Given, decimal number is 3286.
- Perform division or LCM on 3286 with 2.
- From bottom to top, the remainder at every step “0” or “1” is noted.
- Finally, the binary notation of decimal number is noted.
- The following diagram describes the binary notation of the decimal number 3286...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
On our board the output signal on pin 8 of the LS04 is:
IO/M
ROMSEL
WR
ROMRD
IORD
RD
Assume that the circuit in Figure 5.3 indicates an invalid code for binary 1000 and 1001 in addition to the other invalid codes. What fault could cause this indication?
Use the DAC in LPC1768 to output analog values to an analog device.
Chapter 10 Solutions
PROGRAMMABLE LOGIC CONTROLLERS BUNDLE
Ch. 10 - In general, what do data manipulation instructions...Ch. 10 - Prob. 2RQCh. 10 - Prob. 3RQCh. 10 - Prob. 4RQCh. 10 - Prob. 5RQCh. 10 - Prob. 6RQCh. 10 - Prob. 7RQCh. 10 - Prob. 8RQCh. 10 - Prob. 9RQCh. 10 - Prob. 10RQ
Ch. 10 - Prob. 11RQCh. 10 - Prob. 12RQCh. 10 - Prob. 13RQCh. 10 - Prob. 14RQCh. 10 - Prob. 15RQCh. 10 - Prob. 16RQCh. 10 - Prob. 17RQCh. 10 - Prob. 18RQCh. 10 - Prob. 19RQCh. 10 - Prob. 20RQCh. 10 - Prob. 21RQCh. 10 - Prob. 22RQCh. 10 - Prob. 1PCh. 10 - Prob. 2PCh. 10 - Prob. 3PCh. 10 - Prob. 4PCh. 10 - Prob. 7PCh. 10 - Prob. 8PCh. 10 - Prob. 9PCh. 10 - Prob. 10PCh. 10 - Write a program that will cause a light to come on...Ch. 10 - Write a program that will cause a light to come on...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Design a logism circuit that converts a 4-bit binary into base-9? Show screenshot of the circuit.arrow_forwardIf the number 3 is to be printed on the common anode 7 segment display, which of the following should a-b-c-d-e-f-g inputs be?arrow_forward155. Multilevel Amplitude Shift Keying (MASK) is not implemented with pure Amplitude Shift Keying (ASK), it is implemented with a. QAM b. PSK c. FSK d. Binary ASKarrow_forward
- VHDL: Four Bit Wide 2 x 1 Multiplexer What's the VHDL Code for the Four Bit Wide 2 x 1 Multiplexer? If the inputs (Minterm and Input_SEL) equal 0, what's Output_Y in the truth table? If the inputs (Minterm and Input_SEL) equal 1, what's Output_Y in the truth table?arrow_forwardUsing the MSP430FR2355. Assembly language only please (No C code). Analog to digital converters. Produce a blinking output in one external LED on a breadboard. The blinking frequency (hint: the time between toggling) needs to be controlled using a potentiometer as an analog input. Please show me an assembly code on how to control the speed of a blinking external LED (I guess we need to use the XOR operation) with a potentiometer. Please show either a polling example and/or using timers and interrupts. Please show: Pseudocode and assembly code with comments. Thank you so much.arrow_forward275. The term that means data is sent over four wires at the same time is a. 4S b. 4D c. 4W d. 4Rarrow_forward
- A VHDL down counter will output a 16-bit unsigned number. Use VHDL and also with a testbench, please. Thank you!arrow_forwardAssume a digital to analog conversion system uses a 10-bit integer to represent an analog temperature over a range of -10oC to 100oC.arrow_forwardFor the given figure, find the current through the diode. *Express your final answers in three decimal places with proper engineering prefixes, unless the answer is exact (terminating decimal).arrow_forward
- Show the code required to configure the high part of port B (From the Atmega 328P) as inputs and the low part as outputs, and enable the pull-up resistors of the 2 most significant inputs. Show the code sequence that configures port D as input and port B as output, and then transfers the port information to port B.arrow_forwardYou are requested to design 16 x 1 multiplexer, meaning that this combinational circuit has 16 data inputs and produces a single output using selection bits. How many selection bits require? Question 5 options: - 4 - 5 - 2 - 3arrow_forwardGiven a binary data 01010. How many Dual D flip flops IC is at least needed to store this data? What shift would you use, and what will be the serial input to make the desired output 10110?arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning