(II) Assume that a 1.00-kg ball is thrown solely by the action of the forearm, which rotates about the elbow joint under the action of the triceps muscle, Fig. 10–52. The ball is accelerated uniformly from rest to 8.5 m/s in 0.35 s, at which point it is released. Calculate (a) the
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
Modified Mastering Physics With Pearson Etext -- Standalone Access Card -- For Physics For Scientists & Engineers With Modern Physics (5th Edition)
Additional Science Textbook Solutions
Introduction to Electrodynamics
Life in the Universe (4th Edition)
The Cosmic Perspective (8th Edition)
An Introduction to Thermal Physics
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Applied Physics (11th Edition)
- (II) Two masses, mA = 35.0 kg and mB = 38.0 kg, are connected by a rope that hangs over a pulley (as in Fig. 10-59). The pulley is a uniform cylinder of radius 0.381 m and mass 3.1 kg. Initially ma is on the ground and mB rests 2.5 m above the ground. If the system is released, use conservation of energy to deter- mine the speed of mB just before it strikes the ground. Assume the pulley bearing is frictionless. %3D RO mB mA 2.5 m FIGURE 10-59 ba Problem 67. inoni lo (IID) A.arrow_forward(II) A rotating uniform cylindrical platform of mass 220 kg and radius 5.5 m slows down from 3.8 rev/s to rest in 16 s when the driving motor is disconnected. Estimate the power output of the motor (hp) required to maintain a steady speed of 3.8 rev/s.arrow_forward(II) Calculate the angular velocity of the Earth (a) in itsorbit around the Sun, and (b) about its axisarrow_forward
- (II) A small rubber wheel is used to drive a large potterywheel. The two wheels are mounted so that their circularedges touch. The small wheel has a radius of 2.0 cm andaccelerates at the rate of 7.2 rad/s and it is in contact withthe pottery wheel (radius 27.0 cm) without slipping. Calculate (a) the angular acceleration of the pottery wheel, and(b) the time it takes the pottery wheel to reach its requiredspeed of 65 rpmarrow_forward(II) A nonrotating cylindrical disk of moment of inertia I is dropped onto an identical disk rotating at angular speed w. Assuming no external torques, what is the final common angular speed of the two disks?arrow_forwardA 4.00-kg mass and a 3.00-kg mass are attached to opposite ends of a very light 42.0-cm-long horizontal rod (Fig. 8–61). The system is rotating at angular speed w = 5.60 rad/s about a vertical axle at the center of the rod. Determine (a) the kinetic energy KE of the system, and (b) the net force on each mass. 3.00 kg 4.00 kg FIGURE 8-61 Problem 87.arrow_forward
- A 4.00-kg mass and a 3.00-kg mass are attached to opposite ends of a very light 42.0-cm-long horizontal rod (Fig. 8–61). The system is rotating at angular speed v = 5.60 rad/s about a vertical axle at the center of the rod. Determine (a) the kinetic energy KE of the system, and (b) the net force on each mass.arrow_forward(I) Calculate the translational speed of a cylinder when itreaches the foot of an incline 7.20 m high. Assume it startsfrom rest and rolls without slippingarrow_forward(II) The forearm in Fig. 8–46 accelerates a 3.6-kg ball at by means of the triceps muscle, as shown. Calculate (a) the torque needed, and(b) the force that must be exerted by the triceps muscle. Ignore themass of the arm.arrow_forward
- (II) A cooling fan is turned off when it is running at 850 rev/minIt turns 1250 revolutions before it comes to a stop. (a) What was the fan’s angular acceleration, assumedconstant? (b) How long did it take the fan to come to acomplete stop?arrow_forward(II) A small 350-gram ball on the end of a thin, light rodis rotated in a horizontal circle of radius 1.2 m. Calculate(a) the moment of inertia of the ball about the center ofthe circle, and (b) the torque needed to keep the ballrotating at constant angular velocity if air resistance exertsa force of 0.020 N on the ball. Ignore air resistance onthe rod and its moment of inertia.arrow_forward(II) A wheel of diameter 27.0 cm is constrained to rotate in the xy plane, about the z axis, which passes through its center. A force F = (-31.0i + 43.4j) N acts at a' point on the edge of the wheel that lies exactly on the x axis at a particular instant. What is the torque about the rotation axis at this instant?arrow_forward
- College PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax College