![EBK LOGIXPRO PLC LAB MANUAL FOR PROGRAM](https://www.bartleby.com/isbn_cover_images/8220102803503/8220102803503_largeCoverImage.jpg)
EBK LOGIXPRO PLC LAB MANUAL FOR PROGRAM
5th Edition
ISBN: 8220102803503
Author: Petruzella
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Question
Chapter 10, Problem 4P
Program Plan Intro
EQU instruction:
- The Equal (EQU) instruction is used to test whether the given two values are equal or not.
- If the given two values such as Source A and Source B are equal then, the instruction is logically true. Otherwise, the given instruction is logically false.
Terms used:
The following terms are used in the instruction
- Source A
- Source A refers to the address of the first piece of data that is used in the instruction.
- Source B
- Source B refers to the address of the second piece of data that is used in the instruction.
Given:
The instructions used in the given data compare program are the input instructions, which are used to compare two different numerical data values and it compares the words stored in the data to take decisions.
Explanation of Solution
b.
Status of switch S1:
No, it is not required that the switch S1 must be closed to change the numeric value stored in “S...
Explanation of Solution
c.
Numbers to be set on the thumbwheel:
The thumbwheel switch is required to be set on with the Binary Coded Decimal (BCD) value “004” in order to turn on the pilot light.
Explanation:
The given ladder logic diagram has been modified as shown below:
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
3. What instruction should be executed to ensure that the carry flag is in the
set state ? the reset state?
Computer Science - Assembly language code:
Q1. A)
A microprocessor is wired into a sensing control circuit so that the memory locations 42 and 43 each
contain the values 0 or 1.
Memory location 50 is connected to a light switch.
When the value in 50 is 1 the light is on and when it is 0 the light is off.
Write a program to switch on the light on when the values in locations 42 and 43 are both 1, and to
switch off the light when the values in locations 42 and 43 are both 0.
Only use the ARM assembly language instructions, MOV, JMP and JNZ.
Assume that the MOV instruction updates the flags with the status register.
Find out the control signal for the following instructions. The complete datapath and control signals given as following:
Chapter 10 Solutions
EBK LOGIXPRO PLC LAB MANUAL FOR PROGRAM
Ch. 10 - In general, what do data manipulation instructions...Ch. 10 - Prob. 2RQCh. 10 - Prob. 3RQCh. 10 - Prob. 4RQCh. 10 - Prob. 5RQCh. 10 - Prob. 6RQCh. 10 - Prob. 7RQCh. 10 - Prob. 8RQCh. 10 - Prob. 9RQCh. 10 - Prob. 10RQ
Ch. 10 - Prob. 11RQCh. 10 - Prob. 12RQCh. 10 - Prob. 13RQCh. 10 - Prob. 14RQCh. 10 - Prob. 15RQCh. 10 - Prob. 16RQCh. 10 - Prob. 17RQCh. 10 - Prob. 18RQCh. 10 - Prob. 19RQCh. 10 - Prob. 20RQCh. 10 - Prob. 21RQCh. 10 - Prob. 22RQCh. 10 - Prob. 1PCh. 10 - Prob. 2PCh. 10 - Prob. 3PCh. 10 - Prob. 4PCh. 10 - Prob. 7PCh. 10 - Prob. 8PCh. 10 - Prob. 9PCh. 10 - Prob. 10PCh. 10 - Write a program that will cause a light to come on...Ch. 10 - Write a program that will cause a light to come on...
Knowledge Booster
Similar questions
- I am trying to use python to control a stepper motor using callback functions, QT Creator and a raspberry pi. However, I have been unable to get it to work properly. I have an increase speed button as well as s decrease speed button. I want it to be so that when I press either the speed of the stepper rpm changes corresponding to the button pressed. I also have start and stop buttons. Am I going about this correctly?arrow_forwardAs a programmer, you need to design a forward-reverse motor system. When a switch 1 is pressed, the motor will run forward and when a switch 2 is pressed, the motor will run reverse. Use PORT A as input and PORT B as output in PIC16F/18F. Build a suitable program that will fulfill the requirement.arrow_forwardComputer Science A circuit for two output ports (A&C) of the AVR ATmega16 microcontroller each connected to 8 LEDs. Write a program to control the LEDs in a sequence shown by stepping to lit on the LED sequentially as in the figure by toggling the LED at the same time for both ports (500mS) ending at the last state of the figure and looping back inversely to the start. This s done for 3 times back and forth.arrow_forward
- Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter.Execute the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN ICARUSarrow_forwardWrite a sequence of two instructions that set both the Carry and Overflow flags at the same time.arrow_forwardWrite a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. Execute the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOGarrow_forward
- Discussion: 1. What flag condition is tested for by the instruction JNS?arrow_forwardplease try and follow the instructionarrow_forwardWith LOOP instruction the jump gets executed when: Select one: a. When CX reaches zero b. When DI reaches zero c. When SI reaches zero d. None of the options given here e. When zero flag is setarrow_forward
- Write a sequence of two instructions that use addition to set the Zero and Carry flags at thesame timearrow_forwardInstruction: Create a code for an increasing value of LDR. When the value output of LDR is 75% and above all the LED will turn on. If the value output of LDR is 50% to 74% only 4 LED will turn on. If the value output of LDR is below 50% only 2 LED will turn on. P.S: I already made a code *refer to the photo below* but there is some mistake that I cannot determine.arrow_forwardWrite a code for this flow chart in the VHDL programming language for this FPGA board. Idle NO Switch 0 VES NO Switch 1 YES NO Switch 2 YES NO Switch 3 T YES NO Switch 4 YES Switch 5 YES NO Switch 6 YES NO Switch 7 YES Turn on all lights on the display Stoparrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- COMPREHENSIVE MICROSOFT OFFICE 365 EXCEComputer ScienceISBN:9780357392676Author:FREUND, StevenPublisher:CENGAGE L
COMPREHENSIVE MICROSOFT OFFICE 365 EXCE
Computer Science
ISBN:9780357392676
Author:FREUND, Steven
Publisher:CENGAGE L