SHIGLEY'S MECHANICAL ENG.DESIGN W/CODE
10th Edition
ISBN: 9781260243314
Author: BUDYNAS
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 10, Problem 5P
A helical compression spring is made with oil-tempered wire with wire diameter of 0.2 in, mean coil diameter of 2 in, a total of 12 coils, a free length of 5 in, with squared ends.
- (a) Find the solid length.
- (b) Find the force necessary to deflect the spring to its solid length.
- (c) Find the factor of safety guarding against yielding when the spring is compressed to its solid length.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In a compound helical spring, the inner spring is concentric with the outer spring, but is 9 mm shorter. The outer spring has ten coils of mean diameter 24 mm, and the wire diameter is 3 mm. Find the stiffness of the inner spring if an axial load of 150 N causes the outer spring to compress 18 mm. If the mean coil diameter for the inner spring is 15.94 mm, find the wire diameter of the inner spring when it has eight coils. Both the springs are made of the same material having G = 77 GPa.
A helical compression spring with square and ground ends has an outside diameter of 14 mm, 20 total coils, a wire diameter of 2 mm, and a free length of 105 mm. Calculate the spring index, the pitch, the solid length, and the shear stress in the wire when the spring is compressed to its solid length.
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
Chapter 10 Solutions
SHIGLEY'S MECHANICAL ENG.DESIGN W/CODE
Ch. 10 - Within the range of recommended values of the...Ch. 10 - It is instructive to examine the question of the...Ch. 10 - A helical compression spring is wound using...Ch. 10 - The spring in Prob. 10-3 is to be used with a...Ch. 10 - A helical compression spring is made with...Ch. 10 - A helical compression spring is to be made of...Ch. 10 - A helical compression spring is made of hard-drawn...Ch. 10 - The spring of Prob. 107 is to be used with a...Ch. 10 - 109 to 1019 Listed in the tables are six springs...Ch. 10 - 109 to 1019 Listed in the tables are six springs...
Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 12PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 17PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Consider the steel spring in the illustration. (a)...Ch. 10 - A static service music wire helical compression...Ch. 10 - Solve Prob. 1021 by iterating with an initial...Ch. 10 - A holding fixture for a workpiece 37.5 mm thick at...Ch. 10 - Solve Prob. 10-23 by iterating with an initial...Ch. 10 - A compression spring is needed to fit over a...Ch. 10 - A compression spring is needed to fit within a...Ch. 10 - A helical compression spring is to be cycled...Ch. 10 - The figure shows a conical compression helical...Ch. 10 - A helical coil compression spring is needed for...Ch. 10 - Solve Prob. 10-30 using the Goodman-Zimmerli...Ch. 10 - Solve Prob. 10-30 using the Sines-Zimmerli...Ch. 10 - Design the spring of Ex. 10-5 using the...Ch. 10 - Solve Prob. 10-33 using the Goodman-Zimmerli...Ch. 10 - A hard-drawn spring steel extension spring is to...Ch. 10 - The extension spring shown in the figure has...Ch. 10 - Design an infinite-life helical coil extension...Ch. 10 - Prove Eq. (10-40). Hint: Using Castigliunos...Ch. 10 - The figure shows a finger exerciser used by...Ch. 10 - The rat trap shown in the figure uses two...Ch. 10 - Prob. 41PCh. 10 - Prob. 42PCh. 10 - Figure 10-13b shows a spring of constant thickness...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal aim AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3650 N/m. that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. If the weight is 65 N. how many revolutions of the nut are required to bring the pointer back to the mark?arrow_forwardA bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see figure). The maximum possible displacement d or the end of the striking plate is 450 mm. What is the maximum velocity vmaxthat a railway car of weight W = 545 kN can have without damaging the bumping post when it strikes it?arrow_forwardA closed coil helical spring is to deflect 1 mm under the axial load of 100 N at shearing of 90 N/mm2. The spring is to be made of round wire having rigidity modulus of 80 X 104 N/mm2. The mean diameter of the spring is to be 10 times the diameter of the wire. Find the diameter and length of the wire necessary to form the sprinarrow_forward
- Two coaxial closed coil springs make up a standard compound helical spring. When both springs are unloaded, they are not of equal length. If each spring's working stress is to be the same. The wire material has an 80 GPa modulus of rigidity. Find the diameter of steel wire for inner spring and stiffness of inner spring. Also find the stiffness of the compound spring. Outer spring a: Mean coil diameter = 100 mm No. of turns = 15 Wire diameter = 12.5 mm Inner spring b: mean coil diameter = 75 mm No. of turns = 20arrow_forwardA closed-coil helical spring is to have stiffness of 900 N/m in compression with a maximum load of 45 N and a maximum shearing stress of 120 N/mm2.The length of the spring is 45 mm. find the wire diameter, mean coil radius and the number of coils. Take C= 40000 N/mm2arrow_forwardFind the number of active coils of a No. 10 wire Helical Spring index of 7, steady load with spring rate of 46.5 lb/in. maximum allowable stress is 70 ksi. The stiffness of a spring is 98 N/mm of axial compression. Find the Joules of work to increase the compression from 60 mm to 90 mm.arrow_forward
- PROBLEM:2 A spring made from a wire of 2.5 mm diameter and 750 N/sq. mm. as its working stress Mean diameter of 12.5 mm and 15 active coils. Find (a) Stiffness of the spring (b) solid length. Assume that the ends are squared and ground. Take modulus of rigidity as 0.85x105 N/mm2.arrow_forwardA helical compression spring is made of no. 16 music wire. The outside coil diameter of the spring is 1.5 in. The ends are Plain end, ground and there are 13 total turns. (a) Estimate the torsional yield strength of the wire. (b) Estimate the static load corresponding to the yield strength. (c) Estimate the scale of the spring. (d) Estimate the deflection that would be caused by the load in part (b). (e) Estimate the solid length of the spring. ( f ) What length should the spring be to ensure that when it is compressed solid and then released, there will be no permanent change in the free length? (g) Given the length found in part ( f ), is buckling a possibility? (h) What is the pitch of the body coil?arrow_forwardDesign a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, is subjected to a load which varies from 448 N to 975 N. The spring index is 6.2 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa,find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm2.arrow_forward
- A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection for the load range is 8mm and the spring index is 6.if the permissible shear stress and module of rigidity for the material of the spring are 380MPa and 90pa respectively, including the effect of the wire curvature. Design the spring by, determine (A)wire diameter (B) mean coil diameter (C) number of active turns (D)total number of turnsarrow_forwardA spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm, respectively, with a spring index of 4. The wire diameter is 6 mm and the modulus of rigidity is 84 GPa. Which of the following is the active number of turns of the spring?arrow_forwardA spring made from music wire ASTM 228 steel has the following data:Free length=1.75” Outside diameter=0.561”Wire diameter=0.055” Applied load= 14 lbEnds=square and ground both ends hingedNumber of coils=10 G=11.85 x 106psi E= 30 Mpsi Findspring rate, force at solid length,check for buckling,coil clearance and hole diameterarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License