Applied Fluid Mechanics
7th Edition
ISBN: 9780133414622
Author: UNTENER
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 11, Problem 11.47PP
Figure 11.33 shows a part of a chemical processing system in which propyl alcohol at
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A self-priming centrifugal pump is used to pump water at 25°C from a reservoir whose surface is 2.2 m below the centerline of the pump inlet. The pipe is PVC pipe with an ID of 26.0 mm and negligible average inner roughness height. The pipe length from the submerged pipe inlet to the pump inlet is 2.8 m. There are only two minor losses in the piping system from the pipe inlet to the pump inlet: a sharp-edged reentrant inlet (KL = 0.85), and a flanged smooth 90° regular elbow (KL = 0.3). The pump’s required net positive suction head is provided by the manufacturer as a curve fit: NPSHrequired = 2.2 m + [0.0013 m/(Lpm)2 ]V.2 , where volume flow rate is in Lpm. Estimate the maximum volume flow rate (in units of Lpm) that can be pumped without cavitation.
Water (15 C) is transported from an open reservoir to the atmosphere through a new cast iron pipe (d = 4 in). At the end of the pipe there is a fully open gate valve. Evaluate the maximum flow rate (gal / min) through the pipe.
Water is pumped from a reservoir to a tank with a lift of 20.0 ft. The suction pipe, which connects the reservoir to the pump, has a 12in diameter and is 25ft long. The discharge pipe, which connects the pump to the tank, has a 10in diameter and is 450ft long. Both pipes may be classified as clean, smooth cast iron pipes. The suction pipe projects into the reservoir and discharge pipe projects into the tank. Considering all losses, calculate the horsepower required to operate the pump to discharge 1346 gpm into the tank.
Chapter 11 Solutions
Applied Fluid Mechanics
Ch. 11 - Water at 10C flows from a large reservoir at the...Ch. 11 - For the system shown in Fig. 11.14, kerosene (...Ch. 11 - Figure 11.15 shows a portion of a hydraulic...Ch. 11 - Figure 11.16 shows part of a large hydraulic...Ch. 11 - Oil is flowing at the rate of 0.015m3/s in the...Ch. 11 - For the system shown in Fig. 11.18, calculate the...Ch. 11 - A liquid refrigerant flows through the system,...Ch. 11 - Water at 100F is flowing in a 4-in Schedule 80...Ch. 11 - A hydraulic oil is flowing in a drawn steel...Ch. 11 - In a processing plant, ethylene glycol at 77F is...
Ch. 11 - Water at 15C is flowing downward in a vertical...Ch. 11 - Turpentine at 77F is flowing from A to B in a 3...Ch. 11 - ]11.13 A device designed to allow cleaning of...Ch. 11 - Kerosene at 25C is flowing in the system shown in...Ch. 11 - Water at 40C is flowing from A to B through the...Ch. 11 - Oil with a specific gravity of 0.93 and a dynamic...Ch. 11 - Determine the required size of new Schedule 80...Ch. 11 - What size of standard hydraulic copper tube from...Ch. 11 - Water at 60F is to flow by gravity between two...Ch. 11 - The tank shown in Fig. 11.24 is to be drained to a...Ch. 11 - Figure 11.25 depicts gasoline flowing from a...Ch. 11 - For the system in Fig. 11.26, compute the pressure...Ch. 11 - For the system in Fig. 11.26, compute the total...Ch. 11 - For the system in Fig. 11.26 specify the size of...Ch. 11 - A manufacturer of spray nozzles specifies that the...Ch. 11 - Specify the size of new Schedule 40 steel pipe...Ch. 11 - Refer to Fig. 11.27. Water at 80C is being pumped...Ch. 11 - For the system shown in Fig. 11.27 and analyzed in...Ch. 11 - In a water pollution control project, the polluted...Ch. 11 - Repeat Problem 11.29, but use a 3-in Schedule 40...Ch. 11 - Water at 10C is being delivered to a tank on the...Ch. 11 - If the pressure at point A in Fig. 11.29 is 300...Ch. 11 - Change the design of the system in Fig. 11.29 to...Ch. 11 - It is desired to deliver 250 gal/min of ethyl...Ch. 11 - For the system shown in Fig. 11.30, compute the...Ch. 11 - Repeat Problem 11.35, but consider the valve to be...Ch. 11 - Repeat Problem 11.35, but consider the valve to be...Ch. 11 - Figure 11.31 depicts a DN 100 Schedule 40 steel...Ch. 11 - Repeat Problem 11.38 but replace the globe valve...Ch. 11 - Repeat Problem 11.38 but use a DN 125 Schedule 40...Ch. 11 - Repeat Problem 11.38, but replace the globe valve...Ch. 11 - It is desired to drive a small,...Ch. 11 - Figure 11.32 shows a pipe delivering water to the...Ch. 11 - Repeat Problem 11.43, except consider that there...Ch. 11 - A sump pump in a commercial building sits in a...Ch. 11 - For the system designed in Problem 11.45, compute...Ch. 11 - Figure 11.33 shows a part of a chemical processing...Ch. 11 - For the system described in Problem 11.47, and...Ch. 11 - For the system described in Problem 11.47, and...Ch. 11 - For the system described in Problem 11.47, and...Ch. 11 - Analyze the system shown in Fig. 11.11 with...Ch. 11 - Create a program or a spreadsheet for analyzing...Ch. 11 - Create a program or a spreadsheet for determining...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Fluid Mechanich As shown in the figure above, the water flows from the ground floor of a three-story house to the second floor through pipes of 20 mm diameter (average roughness of the pipe material ɛ = 0.0015 mm) with a volumetric flow rate of 0.75 L / s. Water is discharged from the system to atmospheric pressure through a tap with a 12 mm diameter outlet. There are 4 winged elbows, one ball valve and one faucet throughout the installation. Calculate the effective pressure at point 1. (pwater = 998 kg / m3 , uwater = 1.12x10-3 Pa s, g = 9.81 m / s2 )arrow_forward10.) A horizontal pipe gradually reduces from 300 mm diameter section to 100 mm diameter section. The pressure at the 300 mm section is 100 kPa and at the 100 mm section is 70 kPa. If the flow rate is 15 liters/sec of water, compute the head lost between the two sections. Answer: 2.872m Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flowarrow_forwardWater at 15°C is transported from a large open tank to the bottom of another open tank above. The surfaces of the two tanks are kept at 160 ft apart vertically. The pipes used have an ID of 3.5 inches, and a total length of the pipe used is 150 ft. In the system, there are two fully open gate valves, 6 90° elbows, and 2 standard tees. The pump used has a mechanical efficiency of 60%, and the volumetric flow rate of water is at 35 (ft^3)/s. Frictional losses due to sudden contraction and expansion are negligible. Determine the Reynolds number of the flowarrow_forward
- Question 8 Two reservoirs are connected by a pipe whose total length is 360m.From the upper reservoir the pipe is 300mm in diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water levels between the two reservoirs are 8m.Take f=0.006 for the smaller pipe and f=0.005 for the larger pipe.If all the changes in pipe sections are sharp and sudden, calculate the flow rate which can be delivered.arrow_forwardAssume the bore and rod diameters of the single-rod double-actuating cylinder in the differential two-speed cylinder circuits depicted in fig below are 120 and 90 mm, respectively. If the line-relief valve sets the maximum system operating pressure at 10 MPa and the pump supplies a maximum flow of 100 L/min flow, what are the cylinder speed and the load-carrying capacity int he regular and differential extension strokes?arrow_forwardin a given setup, distilled water at 75 degree f has been found to be transported through a one and a half diameter horizontally oriented galvanized iron pipe running 1500 feet with a given flow rate of 0.1 cubic feet per second. what is the pressure drop in the given length of pipe assuming that the friction factor is take as 0.023?arrow_forward
- Calculate the minimum velocity of flow in ft/s of water at 160°F in a 2-in steel tube with a wall thickness of 0.065 in for which the flow is turbulent.arrow_forwardDraw a simple flowchart of a hypothetical oxygen piping system, which has two branches with diameters different from the diameter of the main branch, containing the following components: 1 pressure swing adsorption (PSA) generator. 1 compressor to pressurize the oxygen that will be transported in the tubes. 1 storage tank to retain oxygen before use. 1 industrial combustion process to serve as an energy consumer 2 heat exchangers to control the oxygen temperature. 4 pumps to move oxygen through the piping system. Required quantity of pressure relief valves, flow valves, drains and vents.arrow_forwardwater is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir height=220ft length of pipe= 1500ft final aubdivisiion= 24ft, 20psi 1)determine the normal pipe size 2) if the pipe size is not avalible what size combination will work 3) if we used a 8 inch pipe determine the min thickness 4)determine the max pressure that can deelope in the 8in systemarrow_forward
- A pump is used to lift water at ambient temperature from one tank to another at a rate of 08/50 m3/min. If the pipe diameter is 4 in, calculate the power required to run the pump (efficiency 70%). The pipe material is commercial steel and contains 3 standard radius elbows. Assume h=1 cP. Calculate the Reynolds number and the friction head loss using the Moody chart attached, Using Colebrook equation. Calculate the other losses and the total loss, (Calculate the required power. Flow rate is not necessary for answering the question.arrow_forwardA manufacturer lists the flow coefficient for a certain control valve as 3.5 at a flow rate of 40 gal/min and a fluid Sg of 0.92 when the machine is at operating temperature. What would be the pressure drop across the valve?arrow_forwardFind the air flow rate in the duct. Data: Air pressure: 17 psia air temperature at the inlet: 65 F air temperature at the exit: 125 F duct wall temperature 230 F duct cross section is 1.5 ft by 1 ft length of the heated segment is: 8 ftarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License