Concept explainers
Which bicyclist is more likely to go faster: one who keeps his head and his body in the most upright position or one who leans down and brings his body closer to his knees? Why?
Whether bicyclist who keeps his head and his body in the most upright position is faster than the one who leans down and brings his body closer to his knees.
Explanation of Solution
Write the expression for the drag force.
Here, the coefficient of the drag is
The frontal area of the body is directly proportional to the drag force on the body. If the head of the bicyclist and his body is in the most upright position then the frontal area will also increase. Due to increase in the frontal area, the drag force will also increase. The increase in the drag force results in an increase in the resistance to the free movement of the bicyclist. The increase in the resistance will decrease the velocity of the body.
But, if the bicyclist leans down and brings his body closer to his knees, then the frontal area will decrease. Due to a decrease in the frontal area, the drag force will also decrease. The decrease in the drag force results in the decrease in the resistance to the free movement of the bicyclist. The decrease in the resistance will increase the velocity of the body.
Therefore, the bicyclist one who leans down and brings his body closer to his knees goes faster.
Want to see more full solutions like this?
Chapter 11 Solutions
Fluid Mechanics Fundamentals And Applications
- A ball has a diameter of 28 mm and falls in honey with a terminal velocity of 0.3 m/s. For honey, take ρh = 1360 kg/m3 and νh = 0.04 m2/s. Note: The volume of a sphere is V ¯¯¯=43πr3arrow_forwardDuring major windstorms, high vehicles such as RVs and semis may be thrown off the road and boxcars off their tracks, especially when they are empty and in open areas. Consider a 5000-kg semi that is 9 m long, 2.5 m high, and 2 m wide. The distance between the bottom of the truck and the road is 0.75 m. Now the truck is exposed to winds from its side surface. Determine the wind velocity that will tip the truck over to its side. Take the air density to be 1.1 kg/m3 and assume the weight to be uniformly distributed.arrow_forwardA ski lift has a one-way length of 1 km and a vertical rise of 200 m. The chairs are spaced 20 m apart, and each chair can seat three people. The lift is operating at a steady speed of 10 km/h. Neglecting friction and air drag and assuming that the average mass of each loaded chair is 250 kg, determine the power required to operate this ski lift. Also estimate the power required to accelerate this ski lift in 5 s to its operating speed when it is first turned on.arrow_forward
- What is the difference between streamlined and bluff bodies? Is a tennis ball a streamlined or bluff body?arrow_forwardA U-tube open at both ends is partially filled with water. Oil having a density of 750 kg/m3 is then poured into the right arm and forms a column L = 10.00 cm high. The density of air is 1.29 kg/m3.The right arm is then shielded from any air motion while air is blown across the top of the left arm until the surfaces of the two liquids are at the same height. (d) Determine the pressure difference between the water and oil columns(e) Determine the speed of the air being blown across the left arm.arrow_forwardIt is proposed to meet the water needs of a recreational vehicle (RV) by installing a 3-m-long, 0.5-m-diameter cylindrical tank on top of the vehicle. Determine the additional power requirement of the RV at a speed of 80 km/h when the tank is installed such that its circular surfaces face (a) the front and back (as sketched) and (b) the sides of the RV. Assume atmospheric conditions are 87 kPa and 20°C.arrow_forward
- The 1.5-in (0.125-ft) gap between two large plane surfaces is filled with SAE-30 oil at 80 °F (μ=0.0063 lb.s/ft2). What force is required to drag a very thin plate of 5-ft2 area between the surfaces at a speed of 0.5 ft/s if this plate is equally spaced between the two surfaces.arrow_forwardFind the Power exerted by air on the plate when the drag force on the plate is 42.2 N and the plate moves at a velocity of 17 m/s. 1434.8 W 2.5 W 717.4 W 59.2 W Clear my choicearrow_forwardAt highway speeds, about half of the power generated by the car’s engine is used to overcome aerodynamic drag, and thus the fuel consumption is nearly proportional to the drag force on a level road. Determine the percentage increase in fuel consumption of a car per unit time when a person who normally drives at 55 mi/h now starts driving at 70 mi/h.arrow_forward
- An airport escalator is designed to move 40 people, 75 kg each, upward at a constant speed of 0.6 m/s at 45o slope. Determine the minimum power input needed to drive this escalator. Neglect friction and drag. Please give your answer in kW.arrow_forwardIf a 20 hp fishing boat motor can pull a 1150 kg boat with passengers of total mass 120 kg at a constant velocity of 13 m/s, what is the drag force on the boat by the water?arrow_forwardThe weight of a thin flat plate 50 cm × 50 cm in size is balanced by a counterweight that has a mass of 2 kg, as shown. Now a fan is turned on, and air at 1 atm and 25°C flows downward over both surfaces of the plate (front and back in the sketch) with a free-stream velocity of 10 m/s. Determine the mass of the counterweight that needs to be added in order to balance the plate in this case.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY