College Physics
10th Edition
ISBN: 9781285737027
Author: Raymond A. Serway, Chris Vuille
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 11, Problem 68AP
(a)
To determine
The mass of waxy material required to conduct the bacteriological test.
(b)
To determine
Why the calculation can be done without knowing the mass of the test samples or of the insulation.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Does the temperature of an ideal gas increase, decrease, or stay the same during (a) an isothermal expansion, (b) an expansion at constant pressure, (c) an adiabatic expansion, and (d) an increase in pressure at constant volume?
How much fiberglass insulation (k = 0.035 W/m*K) is needed to guarantee that the outside temperature of a kitchen oven will not exceed 43 degrees Celsius? The maximum oven temperature to be maintained by the conventional type of thermostatic control is 290 degrees Celsius, the kitchen temperature may vary from 15 to 33 degrees Celsius, and the average heat transfer coefficient between the oven surface and the kitchen is 12 W/m2*K.
A cylinder contains 0.100 mol of an ideal monatomic gas. Initially ,the gas is at a pressure of 1.00 x 10^5 Pa and occupies a volume of 2.50 x 10^ -3 cubic meter. If the gas is allowed to expand to twice the initial volume, what is the final temperature if the expansion is adiabatic?
Chapter 11 Solutions
College Physics
Ch. 11.2 - Prob. 11.1QQCh. 11.4 - Prob. 11.2QQCh. 11.5 - Will an ice cube wrapped in a wool blanket remain...Ch. 11.5 - Two rods of the same length and diameter are made...Ch. 11.5 - Stars A and B have the same temperature, but star...Ch. 11 - Prob. 1WUECh. 11 - Physics Review An athlete lifts a 175-kg barbell...Ch. 11 - Prob. 3WUECh. 11 - Convert 3.50 103 cal to the equivalent number of...Ch. 11 - Prob. 5WUE
Ch. 11 - Prob. 6WUECh. 11 - A large room in a house holds 975 kg of dry air at...Ch. 11 - A wooden wall 4.00 cm thick made of pine with...Ch. 11 - A granite ball of radius 2.00 m and emissivity...Ch. 11 - Rub the palm of your hand on a metal surface for...Ch. 11 - In winter, why did the pioneers store an open...Ch. 11 - In warm climates that experience an occasional...Ch. 11 - Prob. 4CQCh. 11 - On a clear, cold night, why does frost tend to...Ch. 11 - The U.S. penny is now made of copper-coated zinc....Ch. 11 - Cups of water for coffee or tea can be warmed with...Ch. 11 - Prob. 8CQCh. 11 - A tile floor may feel uncomfortably cold to your...Ch. 11 - On a very hot day, its possible to cook an egg on...Ch. 11 - Concrete has a higher specific heat than does...Ch. 11 - You need to pick up a very hot cooking pot in your...Ch. 11 - A poker is a stiff, nonflammable rod used to push...Ch. 11 - Star A has twice the radius and twice the absolute...Ch. 11 - Prob. 15CQCh. 11 - The highest recorded waterfall in the world is...Ch. 11 - The temperature of a silver bar rises by 10.0C...Ch. 11 - Lake Erie contains roughly 4.00 1011 m3 of water....Ch. 11 - An aluminum rod is 20.0 cm long at 20.0C and has a...Ch. 11 - A 3.00-g copper coin at 25.0C drops 50.0 m to the...Ch. 11 - Prob. 6PCh. 11 - A 75-kg sprinter accelerates from rest to a speed...Ch. 11 - A sprinter of mass m accelerates uniformly from...Ch. 11 - Prob. 9PCh. 11 - Prob. 10PCh. 11 - Prob. 11PCh. 11 - A 1.5-kg copper block is given an initial speed of...Ch. 11 - A certain steel railroad rails 13 yd in length and...Ch. 11 - Prob. 14PCh. 11 - What mass of water at 25.0C must be allowed to...Ch. 11 - Lead pellets, each of mass 1.00 g, are heated to...Ch. 11 - Prob. 17PCh. 11 - In a showdown on the streets of Laredo, the good...Ch. 11 - Prob. 19PCh. 11 - A 1.50-kg iron horseshoe initially at 600C is...Ch. 11 - A student drops two metallic objects into a 120-g...Ch. 11 - When a driver brakes an automobile, the friction...Ch. 11 - Equal 0.400-kg masses of lead and tin at 60.0C are...Ch. 11 - Prob. 24PCh. 11 - A 75-g ice cube al 0C is placed in 825 g of water...Ch. 11 - Prob. 26PCh. 11 - Prob. 27PCh. 11 - Prob. 28PCh. 11 - Prob. 29PCh. 11 - Prob. 30PCh. 11 - Prob. 31PCh. 11 - Prob. 32PCh. 11 - A high-end gas stove usually has at least one...Ch. 11 - Prob. 34PCh. 11 - Steam at 100.C is added to ice at 0C. (a) Find the...Ch. 11 - The excess internal energy of metabolism is...Ch. 11 - A 3.00-g lead bullet at 30.0C is fired at a speed...Ch. 11 - A glass windowpane in a home is 0.62 cm thick and...Ch. 11 - A pond with a flat bottom has a surface area of...Ch. 11 - The thermal conductivities of human tissues vary...Ch. 11 - A steam pipe is covered with 1.50-cm-thick...Ch. 11 - The average thermal conductivity of the walls...Ch. 11 - Consider two cooking pots of the same dimensions,...Ch. 11 - A thermopane window consists of two glass panes,...Ch. 11 - A copper rod and an aluminum rod of equal diameter...Ch. 11 - A Styrofoam box has a surface area of 0.80 m and a...Ch. 11 - A rectangular glass window pane on a house has a...Ch. 11 - Prob. 48PCh. 11 - Measurements on two stars indicate that Star X has...Ch. 11 - The filament of a 75-W light bulb is at a...Ch. 11 - The bottom of a copper kettle has a 10.0-cm radius...Ch. 11 - A family comes home from a long vacation with...Ch. 11 - A 0.040.-kg ice cube floats in 0.200 kg of water...Ch. 11 - The surface area of an unclothed person is 1.50...Ch. 11 - A 200-g block of copper at a temperature of 90C is...Ch. 11 - Prob. 56APCh. 11 - A student measures the following data in a...Ch. 11 - Prob. 58APCh. 11 - A class of 10 students; taking an exam has a power...Ch. 11 - A class of 10 students taking an exam has a power...Ch. 11 - A bar of gold (Au) is in thermal contact with a...Ch. 11 - An iron plate is held against an iron, wheel so...Ch. 11 - Prob. 63APCh. 11 - Three liquids are at temperatures of 10C, 20C, and...Ch. 11 - Prob. 65APCh. 11 - A wood stove is used to heat a single room. The...Ch. 11 - Prob. 67APCh. 11 - Prob. 68APCh. 11 - The surface of the Sun has a temperature of about...Ch. 11 - The evaporation of perspiration is the primary...Ch. 11 - Prob. 71APCh. 11 - An ice-cube tray is filled with 75.0 g of water....Ch. 11 - An aluminum rod and an iron rod are joined end to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- An aluminum rod 0.500 m in length and with a cross-sectional area of 2.50 cm2 is inserted into a thermally insulated vessel containing liquid helium at 4.20 K. The rod is initially at 300 K. (a) If one-half of the rod is inserted into the helium, how many liters of helium boil off by the time the inserted half cools to 4.20 K? Assume the upper half does not yet cool. (b) If the circular surface of the upper end of the rod is maintained at 300 K, what is the approximate boil-off rate of liquid helium in liters per second after the lower half has reached 4.20 K? (Aluminum has thermal conductivity of 3 100 W/m K at 4.20 K; ignore its temperature variation. The density of liquid helium is 125 kg/m3.)arrow_forwardIn 1993, the U.S. government instituted a requirement that all room air conditioners sold in the United States must have an energy efficiency ratio (EER) of 10 or higher. The EER is defined as the ratio of the cooling capacity of the air conditioner, measured in British thermal units per hour, or Btu/h, to its electrical power requirement in watts. (a) Convert the EER of 10.0 to dimensionless form, using the conversion 1 Btu = 1 055 J. (b) What is the appropriate name for this dimensionless quantity? (c) In the 1970s, it was common to find room air conditioners with EERs of 5 or lower. State how the operating costs compare for 10 000-Btu/h air conditioners with EERs of 5.00 and 10.0. Assume each air conditioner operates for 1 500 h during the summer in a city where electricity costs 17.0 per kWh.arrow_forwardA sample of a monatomic ideal gas occupies 5.00 L at atmospheric pressure and 300 K (point A in Fig. P17.68). It is warmed at constant volume to 3.00 atm (point B). Then it is allowed to expand isothermally to 1.00 atm (point C) and at last compressed isobarically to its original state. (a) Find the number of moles in the sample. Find (b) the temperature at point B, (c) the temperature at point C, and (d) the volume at point C. (e) Now consider the processes A B, B C, and C A. Describe how to carry out each process experimentally. (f) Find Q, W, and Eint for each of the processes. (g) For the whole cycle A B C A, find Q, W, and Eint. Figure P17.68arrow_forward
- (a) The inside of a hollow cylinder is maintained at a temperature Ta, and the outside is at a lower temperature, Tb (Fig. P19.45). The wall of the cylinder has a thermal conductivity k. Ignoring end effects, show that the rate of energy conduction from the inner surface to the outer surface in the radial direction is dQdt=2Lk[TaTbln(b/a)] Suggestions: The temperature gradient is dT/dr. A radial energy current passes through a concentric cylinder of area 2rL. (b) The passenger section of a jet airliner is in the shape of a cylindrical tube with a length of 35.0 m and an inner radius of 2.50 m. Its walls are lined with an insulating material 6.00 cm in thickness and having a thermal conductivity of 4.00 105 cal/s cm C. A heater must maintain the interior temperature at 25.0C while the outside temperature is 35.0C. What power must be supplied to the heater? Figure P19.45arrow_forwardCompare the charge in internal energy of an ideal gas for a quasi-static adiabatic expansion with that for a quasi-static isothermal expansion. What happens to the temperature of an ideal gas in an adiabatic expansion?arrow_forwardFor a temperature increase of 10 at constant volume, what is the heat absorbed by (a) 3.0 mol of a dilute monatomic gas; (b) 0.50 mol of a dilute diatomic gas; and (c) 15 mol of a dilute polyatomic gas?arrow_forward
- During a long sleepless night, you wonder about the thermodynamic properties of the air in your room. If your room has a volume of 24 m3, the pressure is 9.9x 104 Pa and the temperature is 20°C, what is the total translational kinetic energy of the air molecules in your room?arrow_forwardThe human body must maintain its core temperature inside a rather narrow range around 37°C. Metabolic processes, notably muscular exertion, convert potential energy into internal energy deep in the interior. From the interior, energy must flow out to the skin or lungs to be expelled to the environment. During moderate exercise, an 80-kg man can metabolize food energy at the rate 300 kcal/h, do 60 kcal/h of mechanical work, and put out the remaining 240 kcal/h of energy by heat. Most of the energy is carriedfrom the body interior out to the skin by forced convection, whereby blood is warmed in the interior and then cooled at the skin, which is a few degrees cooler than the body core. Without blood flow, living tissue is a good thermal insulator, with thermal conductivity about 0.210 W/m · °C. Show that blood flow is essential to cool the man’s body by calculatingthe rate of energy conduction in kcal/h through the tissue layer under his skin. Assume that its area is 1.40 m2, its…arrow_forwardAssume a person has lungs that can hold V = 4.9 L of air (at 1 atm), and their body temperature is currently T = 38° C. How many moles of air does the average human have in their lungs when they breath in?arrow_forward
- An automobile wheel contains air with a pressure of 3x10^5 Pa at 25 C. The sipop cover was removed and the air was allowed to expand adiabatically against an external pressure of 10^5 Pa. What is the final temperature of the gas in the wheel? (It should be taken into account that the gas behaves ideally and the Cp value for air is 7/2R)arrow_forwardAir enters an adiabatic nozzle at 60 psia, 5408F, and 200 ft/s and exits at 12 psia. Assuming air to be an ideal gas with variable specific heats and disregarding any irreversibilities, determine the exit velocity of the air.arrow_forwardHow much energy must be transferred as heat for a reversible isothermal expansion of an ideal gas at 132 degrees Celcius if the enthropy of the gas increases by 46.0 J/Karrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning