For the given data, weight percentage of manganese is to be determined, where Mn to Ba count ratio is 0.936 considering barium as internal standard. Concept introduction: Weight percentage of Mn is calculated by plotting the graph between ratio of fluorescence intensity and weight percentage of Mn. The values used for this graph will be obtained by using a spreadsheet for the given data and calculation between cells of spreadsheet. Unknown quantities and required quantities are obtained by the calculation which will be done between cells of spreadsheet.

Question

Quinine in a 1.939-g tablet was to be analyzed by dissolving it with 0.10 M HCl to a final volume of exactly 500 mL. This solution was diluted by adding 50.00 mL to a 100.0 mL flask and diluting to the mark. Afterwards the fluorescence intensity was found to be 394 in arbitrary units. Under identical experimental conditions, a standard 150.0-ppm had an intensity of 184.Quinine in a 1.939-g tablet was to be analyzed by dissolving it with 0.10 M HCl to a final volume of exactly 500 mL. This solution was diluted by adding 50.00 mL to a 100.0 mL flask and diluting to the mark. Afterwards the fluorescence intensity was found to be 394 in arbitrary units. Under identical experimental conditions, a standard 150.0-ppm had an intensity of 184. Calculate the number of milligrams in the original sample.

Answer 1

Question

Chapter 12, Problem 12.12QAP

Interpretation Introduction

Interpretation:

For the given data, weight percentage of manganese is to be determined, where Mn to Ba count ratio is 0.936 considering barium as internal standard.

Concept introduction:

Weight percentage of Mn is calculated by plotting the graph between ratio of fluorescence intensity and weight percentage of Mn. The values used for this graph will be obtained by using a spreadsheet for the given data and calculation between cells of spreadsheet. Unknown quantities and required quantities are obtained by the calculation which will be done between cells of spreadsheet.

Expert Solution & Answer

Trending nowThis is a popular solution!

See solution

Check out sample textbook solution

Students have asked these similar questions

Quinine in a 1.939-g tablet was to be analyzed by dissolving it with 0.10 M HCl to a final volume of exactly 500 mL. This solution was diluted by adding 50.00 mL to a 100.0 mL flask and diluting to the mark. Afterwards the fluorescence intensity was found to be 394 in arbitrary units. Under identical experimental conditions, a standard 150.0-ppm had an intensity of 184.Quinine in a 1.939-g tablet was to be analyzed by dissolving it with 0.10 M HCl to a final volume of exactly 500 mL. This solution was diluted by adding 50.00 mL to a 100.0 mL flask and diluting to the mark. Afterwards the fluorescence intensity was found to be 394 in arbitrary units. Under identical experimental conditions, a standard 150.0-ppm had an intensity of 184. Calculate the number of milligrams in the original sample.

The nickel level in a soil sample was determined using AAS. A 3.0 g sample was dissolved in acid and then diluted to a total volume of 100.0 mL. The absorbance of this solution determined at a wavelength of 232 nm, was found to be0.3. Several standard solutions were tested under the same conditions and a calibration curve shown below was obtained. Calculate the mass of nickel in mg.

In order to measure riboflavin in a breakfast cereal, a 5.00-gram sample of the cereal was extracted with acetic acid and filtered. The extract was transferred to a 50.0 mL volumetric flask and diluted to the mark. The sample was transferred to a cuvette and the fluorescence was measured. The instrument read 59 units (Fluorescence units –an arbitrary scale). 24.00 mL of the cereal extract was sample was mixed with 1.0 mL of a riboflavin standard that was 0.500 ug/mL. The fluorescence of this mixture was measured and read 94 fluorescence units. Calculate the concentration of riboflavin per gram of cereal (use µg/gram of cereal).