Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 12.13PP
Work Problem 12.4 using PIPE-FLO® software. Display the volume flow rate in each branch and all other relevant values on the FLO-Sheet®.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Benzene (SG=0.86) at 60°C is flowing at 25 L/min in a DN 25 Schedule 80 steel pipe. Is the flow laminar or turbulent? Explain.
Calculatethe energy loss for water flowing at 8m/sthrough a standard tee fitting withan18-in ductile iron pipeif the flow is through the run of the tee.
Thermal power plant burns 200 kilolitres diesel per day. In ideal conditions, burning of 1.0 kg diesel requires 14.2 kg of air. Parallel plate type ESP is installed to remove the particulates. If the height of channels is 4.5 m and the spacing between electrodes is 0.25 m, calculate:
(i) Flue gas discharge in m3 per day
(ii) The number of channels required
(iii) Number of discharge electrodes provided
(iv) Number of chambers required
Chapter 12 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 12 - Figure 12.7 shows a branched system in which the...Ch. 12 - Using the system shown in Fig. 12.2 and the data...Ch. 12 - In the branched pipe system shown in Fig. 12.8...Ch. 12 - In the branched-pipe system shown in Fig. 12.9...Ch. 12 - A 160mm pipe branches into a 100mm and a 50mm pipe...Ch. 12 - For the system shown in Fig. 12.11 the pressure at...Ch. 12 - Solve Problem 12.4 using the Cross technique.Ch. 12 - Solve Problem 12.3 using the Cross techniqueCh. 12 - Find the flow rate of water at 60Fin each pipe of...Ch. 12 - Figure 12.13 represents a spray rinse system in...
Ch. 12 - Figure 12.14 represents the water distribution...Ch. 12 - Figure 12.15 represents the network for delivering...Ch. 12 - Work Problem 12.4 using PIPE-FLO software. Display...Ch. 12 - 2. Enhance the program from Assignment 1 so that...Ch. 12 - Write a program or a spreadsheet for analyzing...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine the smallest metric hydraulic copper tube size that will carry 4L/min of thefollowing fluids while maintaining laminar flow: (a) water at 40°C, (b) gasoline(SG=0.68) 25°C, (c) ethyl alcohol (SG=0.79) at 0°C, and (d) heavy fuel oil at 25°C. answer correctly the last part only please thank youarrow_forwardTractor mounted sprayer having 14 nozzles 60 cm apart is moving at a forward speed of 35 km/h. The chemical mixed with water is to be applied at the rate of 75 lit /ha, at pressure of 500 kPa calculate the following-a) The rate of spray per nozzle in litminb) Pump efficiency if liquid lost in the system is 10%.c) Horsepower of engine if the pump and Power required for agitating the water 1/10th of rated power of engine c) height of Spray from the ground if the spray angle is 60 degrees & each nozzle should Spray 25 % more than nozzle Spacingarrow_forwardDetermine the power requirements for 3 m diameter, six-blade flatblade turbine impeller mixer running at 15 rpm in a 10 m diametermixing tank. Assume the fluid being mixed is water.arrow_forward
- A machined entrance cone venture tube that has been fabricated according to ASME standards is fit to a 7 cm ID water pipe. The minimum diameter is 4 cm. If the pressure drop across the venture is 19 kPa, calculate the water flow rate.arrow_forward1) If the electrical power required for a house is assumed to be 5kW, the requirement of 150044 houses.A HES with the installed capacity to meet the needs will be established. This installed power includes 7 generators and it will be provided from the penstock pair. Net water head 190 m and penstock calculated for the facility 91% efficiency, 85% turbine efficiency, 96% generator efficiency, transformer efficiency.It is calculated to be 93%. Calculate the required water flow for each force. (ρ: specific weight: 1000 kg /m³, g: Gravitational acceleration: 9.81 m/s²) 2)In this example, if the total efficiency of the system could be increased to 85%, how would the required water flow rate?would be affected? Show by calculatingarrow_forwardA flexible tube peristaltic pump operates at 100 rpm, with a lobe volume of approximately 3 ml. What is the flow rate?arrow_forward
- 10. What hose I.D. would be required to deliver 50 gal/min , assuming no friction losses at a maximum velocity of 8.5 ft/sec?arrow_forwardDraw a simple flowchart of a hypothetical oxygen piping system, which has two branches with diameters different from the diameter of the main branch, containing the following components: 1 pressure swing adsorption (PSA) generator. 1 compressor to pressurize the oxygen that will be transported in the tubes. 1 storage tank to retain oxygen before use. 1 industrial combustion process to serve as an energy consumer 2 heat exchangers to control the oxygen temperature. 4 pumps to move oxygen through the piping system. Required quantity of pressure relief valves, flow valves, drains and vents.arrow_forwardHow long would it take to purge a 10mm section of a 20 cm dia.eter pipe using a flow rate 17L/min?arrow_forward
- Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following fluids while maintaining laminar flow: (a) water at 40°C, (b) gasoline (SG=0.68) 25°C, (c) ethyl alcohol (SG=0.79) at 0°C, and (d) heavy fuel oil at 25°C.arrow_forwardSpecifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe in the one inch branch is 8 ft. Brine (sg=1.04, m=10-3Pa*s) flows at 250gpm through the entrance at point A. Assume fully turbulent flow in both branches (f=ft). Pipes are standard Schedule 40 steel pipes. Assume the globe valve is partially shut so its equivalent L/D is 1000. For Part 1 of this project, you are tasked with determining the following: The flow rate in both branches The pressure drop in both branches The overall resistance coefficientarrow_forwardCalculate the power supplied to the pump shown if its efficiency is 75%. Water is at 25 degrees Celsius is flowing at the rate of 50.0 m3/h. The suction linf is a standard DN 100 Schedule 40 steel pip, 15m long. The total length of DN 50 Schedule 40 steel pipe in the discharge line is 200m. The elbows are tight, the entrance to the pipe is flush and the globe valve is completely open. Draw the line of total and piezometric heights.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License