Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 12, Problem 15RQ
To determine
The effect of nominal and tolerance values in manufacturing process.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What are the significance of tolerance and allowance in production process? Diagram?
What is the size obtained in the manufacture of parts and which is measured with an acceptable accuracy?
1) limit 2) actual 3) nominal
What is the testing plan for universal testing machines? How are the tests to be done is planned in the beginning to the end?
Chapter 12 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 12 - Define accuracy or precision in terms of a...Ch. 12 - What does the nature of the process refer to?Ch. 12 - Suppose you have a pistol�shooting process that...Ch. 12 - Review the steps required to make a PC study of a...Ch. 12 - Why do not standard tables exist detailing the...Ch. 12 - Here are some common, everyday processes with...Ch. 12 - Why might the diameter measurements for holes...Ch. 12 - What are some common manufactured items that may...Ch. 12 - What are common reasons for sampling inspection...Ch. 12 - Fill in this table with one of the four following...
Ch. 12 - Now explain why when we sample, we cannot avoid...Ch. 12 - Which error can lead to legal action from the...Ch. 12 - Define and explain the difference between andX and...Ch. 12 - What is Cp, and why is a value of 0.80 not good?...Ch. 12 - Prob. 15RQCh. 12 - What are some of the alternatives available to you...Ch. 12 - Cpk is another process capability index. How does...Ch. 12 - In a sigma chart, are σ values for the samples...Ch. 12 - What is an assignable cause, and how is it...Ch. 12 - Why is the range used to measure variability when...Ch. 12 - How is the standard deviation of a distribution of...Ch. 12 - In the last two decades, the quality in...Ch. 12 - Figure 12.15 shows a bimodal check sheet...Ch. 12 - Control charts use upper and lower control limits....Ch. 12 - In Figure 12.10, what are the USL and the LSL,...Ch. 12 - What are four major branches (fishbones) on a...Ch. 12 - How does variation in the measuring device...Ch. 12 - What are Taguchi or factorial experiments, and how...Ch. 12 - How does the Taguchi approach differ from the...Ch. 12 - Why are Taguchi experiments so important compared...Ch. 12 - Explain what happed to improve the process inÂ...Ch. 12 - In Table 12.1, explain MOâ€�COâ€�MOO....Ch. 12 - What is a quality circle, and how might you apply...Ch. 12 - Which of the seven QC tools is being used inÂ...Ch. 12 - Go to a subway restaurant and develop a process...Ch. 12 - What do you estimate the standard deviation of...Ch. 12 - Is the dashed line in the figure labeled mean the...Ch. 12 - From the information given in the discussion and...Ch. 12 - What is the most glaring error in the figure, and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How do expectations about future economic conditions influence the speed of adjustment in the error correction model (ECM)? Are there any other factors that might affect the speed of adjustment?arrow_forwardWhich order arranges the following manufacturing processes from the least precise to the most precise tolerance limits?POSSIBLE ANSWERS1 . Turning, grinding, casting2 . Casting, turning, grinding3 . Casting. grinding, turning4 . Turning, casting, grindingarrow_forwardWhat are codes and standards?arrow_forward
- Q:02 Write Down the application of manufacturing processes in the field of mechanical Engineering?arrow_forwardA critical part has a manufacturing specification of 4.5 cm ± 0.10. If this measurement is larger than 4.6 or smaller than 4.4, the product fails at a cost of $150.a. Calculate the k value for Taguchi loss function. What is the Taguchi loss function for this part?b. Using the above Taguchi loss function, determine the estimated loss for when the actual part dimension is 4.46 cm.arrow_forwardA customer has recently tightened the specs for a part your company supplies. The specs are nowmuch tighter than the machine being used for the job is capable of. Briefly identify alternativesyou might consider to resolve this problem.arrow_forward
- What do you mean by reliability factor (KR) in machine design" What kind of functional relationship exist between KR and reliability. Please write typed. Handwriting is difficult to understand and I have to repeat the question.arrow_forwardOn what produced part below, show a simple sketch on how the flatness on the part may be verified and how the resultant flatness tolerance zone is defined. Please refer to attached image.arrow_forwardWhat is the need for calibration of instruments? Write the steps followed in industries for calibrationarrow_forward
- What is the 95% confidence interval for each of the three measured parameters?arrow_forwardResearch and identify one type of geometric tolerances (besides obvious specs like length, distance, diameter, etc.) that can be called out on a technical drawing. Explain how this tolerance is definedarrow_forwardOM A customer has recently tightened the specs for a part your company supplies. The specs are now much tighter than the machine being used for the job is capable of. Briefly identify alternatives you might consider to resolve this problem.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning