EBK ACTIVITIES MANUAL FOR PROGRAMMABLE
5th Edition
ISBN: 8220102795983
Author: Petruzella
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 12, Problem 19RQ
Program Plan Intro
BSL instruction:
- BSL is the abbreviation for Bit Shift Left.
- BSL shifts the bit status from a lower address number to a higher address number.
- First it loads the data into an array, then shifts the data pattern through the array to the left, and finally unloads the last bit of data in the array.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Explain the operation of POP CX instruction.
(d) The table below shows the ALUcontrol signal of the datapath we discussed in class.
Instruction
Funct
ALU
Орсode
ALUop
ALU action
operation
field
control
Iw
00
load word
XXXXXX
add
0010
Sw
00
store word
XXXXXX
add
0010
beq
01
branch equal
subtract
0110
XXXXXX
R-type
10
add
100000
add
0010
R-type
10
subtract
100010
subtract
0110
R-type
10
AND
100100
AND
0000
R-type
10
OR
100101
OR
0001
R-type
10
set on less than
101010
set on less than
0111
You want to add the bne instruction into the datapath, which already includes the
required hardware for the instruction. Write out the ALUop for bne and how you can
determine whether the bne results in the branch to be taken.
What happens to the Carry flag when the SHR AX,1 instruction is executed?
Chapter 12 Solutions
EBK ACTIVITIES MANUAL FOR PROGRAMMABLE
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- What is wrong with a MOV [BX],[DI] instruction?arrow_forward4. Which segment will be accessed for the instruction MOV [BX],AH.arrow_forwardCategory: CPU Wiring Look at the following (incomplete) diagram of the Hack CPU taken from figure 5.9 of the textbook. ALU output outM instruction AM inM writeM A addressM inc reset PC po Match the wires A, B, C, D and E with the logic expression that describes the signal they should carry. The logic expressions use the operators not (!), and (&&) and or (I). The 16 wire instruction is named instr. The A and C instruction formats are: A-instruction: 0 V. V. V C-instruction: 1 1 1 a c1 c2 c3 c5 c6 d1 d2 d3 j1 j2 j3 Mire number: 15 14 13 12 11 10 9 8 6. 4 3 1 instr[15) && instr[3] B. instr[14] ALUarrow_forward
- This R format instruction adds the four bytes that the source register holds and puts the sum into the lower two bytes of the destination register.arrow_forwardIn the event an instruction is refused, what would be the result? In the following cases, a software-managed TLB is faster than a hardware-managed TLB:arrow_forwardSelect an instruction that tests bit position 8 of register CH. Select the correct response: None of the choices BT CH, 8 TEST CH, 128 a or barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning