AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
6th Edition
ISBN: 9780135257418
Author: Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Question
Chapter 12, Problem 4RQ
To determine
The list of gaps or clearance that can be measured using a feeler gauge.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
what are plug gauges ? how to use them to judge a qualified part?
advantage and disadvantages of using STRAIN GAUGE
36) (SI units) A GO/NO-GO plug gauge will be designed to inspect a 60.00 +/- 0.40mm diameter hole. A wear allowance of 3% of the total tolerance band is applied to the GO side of the gauge. Determine the nominal sizes of the NO-GO gauge. Round your answer to the nearest thousandth of a mm
Chapter 12 Solutions
AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
Ch. 12 - Explain how a micrometer is read.Ch. 12 - Describe how to check a crankshaft journal for...Ch. 12 - List engine components that can be measured with...Ch. 12 - Prob. 4RQCh. 12 - Prob. 5RQCh. 12 - Prob. 1CQCh. 12 - Prob. 2CQCh. 12 - Prob. 3CQCh. 12 - Prob. 4CQCh. 12 - To directly measure the diameter of a valve guide...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- (USCS UNITS) A GO/NO GO PLUG GAUGE WILL BE DESIGNED TO INSPECT A 2.000 +/- 0.002mm DIAMETER HOLE. A WEAR ALLOWANCE OF 5% OF THE TOTAL TOLERANCE BAND IS APPLIED TO THE GO SIDE OF THE GAUGE. DETERMINE THE NOMINAL SIZES OF THE GO GAUGE. ROUND YOUR ANSWER TO THE NEAREST TENTH OF A THOUSANDTH OF AN INCHarrow_forwarddimension the distance between the holes, using bilateral tolerancearrow_forwardBriefly discuss the concept behind each of the following measuring devices:a. LVDTb. strain gaugec. proving ringd. load cellarrow_forward
- An improved verity of surface gauge is universal surface gauge and a marking tool. Select one: True Falsearrow_forwardMeasuring Thickness of the Sheetmetal is possible with the following device Select one: a. Steel gauge b. Circumference Rule gauge c. Folding Rule d. Sheet metal gaugearrow_forwardIn charpy test specimen, the angle of v-notch section is_- a. 60 degrees o b. 30 degrees O c. 90 degrees o d. 45 degreesarrow_forward
- What is the minimum distance from the holes at each end of the part? 2x Ø 1.375-1.390 +ø010 DABC 2x Ø.010 @ LMC Tolerance zones 2.000-2.020 1.000 1.000 4.000 - 6.000-6.020 - Your answerarrow_forwardDiscuss thoroughly the causes of deviation in the readings between the true reading and the gage reading.arrow_forwardAll form tolerances are surface controls except for Form tolerances are independent of all other andarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY