EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Question
Chapter 12, Problem 5RQ
To determine
Why are ribs useful for flat surfaces?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
For symmetric and large circular section which pattern is preferred? Explain with figures
Comparing the processes of tube drawing and tube sinking:
a
tube sinking use a mandrel
b
tube sinking preciously controls the inside diameter
c
tube drawing uses a mandrel
d
tube drawing is used with thick walled tubes
When are the thin-walled tubes of the noncircular cross-section often used to construct?
Chapter 12 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 12 - Why are steels more difficult to cast than cast...Ch. 12 - What is the significance of hot spots in metal...Ch. 12 - What is shrinkage allowance? Machining allowance?Ch. 12 - Explain the reason for drafts in molds.Ch. 12 - Prob. 5RQCh. 12 - What are light castings and where are they used...Ch. 12 - Name the types of cast irons generally available,...Ch. 12 - Comment on your observations regarding Fig. 12.5.Ch. 12 - Describe the difference between a runner and a...Ch. 12 - What is the difference between machining allowance...
Ch. 12 - What is dross? Can it be eliminated?Ch. 12 - Describe your observation concerning the design...Ch. 12 - If you need only a few castings of the same...Ch. 12 - Do you generally agree with the cost ratings in...Ch. 12 - Describe the nature of the design differences...Ch. 12 - Note in Fig. 12.5 that the ductility of some cast...Ch. 12 - Do you think that there will be fewer defects in a...Ch. 12 - Explain the difference in the importance of drafts...Ch. 12 - What type of cast iron would be suitable for...Ch. 12 - Explain the advantages and limitations of sharp...Ch. 12 - Explain why the elastic modulus, E, of gray cast...Ch. 12 - If you were to incorporate lettering or numbers on...Ch. 12 - The general design recommendations for a well in...Ch. 12 - The heavy regions of parts typically are placed in...Ch. 12 - What are the benefits and drawbacks to having a...Ch. 12 - When designing patterns for casting, patternmakers...Ch. 12 - Using the information given in Table 12.2, develop...Ch. 12 - The part in Figure P12.28 is to be cast of 10% Sn...Ch. 12 - Describe the general design considerations...Ch. 12 - Add more examples of applications to those shown...Ch. 12 - Explain how ribs and serrations are helpful in...Ch. 12 - List casting processes that are suitable for...Ch. 12 - Small amounts of slag and dross often persist...Ch. 12 - If you need only a few units of a particular...Ch. 12 - For the cast metal wheel illustrated in Fig....Ch. 12 - Assume that the introduction to this chapter is...Ch. 12 - In Fig. P12.37, the original casting design shown...Ch. 12 - An incorrect and a correct design for casting are...Ch. 12 - Using the method of inscribed circles, shown in...Ch. 12 - A growing trend is the production of patterns and...Ch. 12 - Repeat Problem 12.40 for the case where (a) a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- some examples about deep drwing?arrow_forward4) In the deep drawing of cups, blanks show a tendency to wrinkle up around the periphery (flange). The most likely cause and remedy of the phenomenon are respectively: Buckling due to circumferential compression; Increase blank holder pressure. High blank holder pressure and high friction; Reduce blank holder pressure and apply lubricant. High temperature causing an increase in circumferential length; Apply coolant to blank. Buckling due to circumferential compression; decrease blank holder pressure.arrow_forwardExplain when we use sectional views and how they are made?arrow_forward
- Properties of areas of common shapes. INCLUDE ALL THE REFERENCE (LINKS)arrow_forwardQuestion 2. It is reduced to 80 mm with forging by stacking a part with a height of 120 mm and a diameter of 75 mm. The friction coefficient between the workpiece and the mold is 0.13. The flow curve of the workpiece is defined by a strength coefficient of 165 MPa and a ping-top of 0.24. Calculate the force during the process at the moments given below and obtain the force-workpiece height graph (1) as soon as it reaches the flow point (flow unit shape change = 0.002), (2) height h = 115 mm, (3) height h = 110 mm, (4) height h = 105 mm, (5) height h = 100 mm, (6) height h = 95 mm, (7) height h = 90 mm, (8) height h = 85 mm, (9) height h = 80 mm,arrow_forwardWhat two hot forming processes can convert steel skelp into pipe?arrow_forward
- 144 About industrial piping, answer questions: WHAT IS THE PURPOSE OF THE FORM COEFFICIENT FOR THE CALCULATION OF FLEXIBILITY?arrow_forwardIndustrial pipes Expansion joints are fragile elements and therefore should be avoided as much as possible in the project, only when there is no space to place expansion joints or curves in sufficient quantity to give flexibility to the section?arrow_forward10 Fig. (6) 8 MPaarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Relationship Between Elastic Constants and Connecting Equations; Author: Engineers Academy;https://www.youtube.com/watch?v=whW5PnM7Pug;License: Standard Youtube License