LogixPro PLC Lab Manual for Programmable Logic Controllers
5th Edition
ISBN: 9781259680847
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 13, Problem 11RQ
Program Plan Intro
Voltage spike:
- Voltage spike refers to a sudden increase in voltage which lasts for less than 3 nanoseconds.
- It is also known as voltage surge.
- A corresponding increase in current is produced by the effect of a voltage spike.
- Some voltage spikes are also created by current sources.
Diode:
- Diode refers to a two-terminal electrical device which conducts current primarily in one direction.
- It has ideally zero resistance in one direction and ideally infinite in the other direction.
Inductive loads:
- The function of an inductive load is to convert the current into a magnetic field.
- Inductive reactance will resist changes in current, and, when measuring current, it lags the voltage.
- Motors, transformers, and chokes are some of the example devices that produce inductive loads.
- Inductance is measured in Henry.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
In CMOS circuit when the pullup part is "on" and the pulldown is "on" then the logic output is
Bipolar junction transistors (BJTs) are considered “normally-off” devices, because their natural state with no signal applied to the base is no ........... between emitter and collector, like an open switch. * Your answer
Explain the steps in designing Combinational Circuits
Chapter 13 Solutions
LogixPro PLC Lab Manual for Programmable Logic Controllers
Ch. 13 - Prob. 1RQCh. 13 - Prob. 2RQCh. 13 - Prob. 3RQCh. 13 - List three potential noise-generating inductive...Ch. 13 - Prob. 5RQCh. 13 - Prob. 6RQCh. 13 - Prob. 7RQCh. 13 - Under what condition can a ground loop circuit be...Ch. 13 - Prob. 9RQCh. 13 - What operating state will cause an inductive load...
Ch. 13 - Prob. 11RQCh. 13 - Prob. 12RQCh. 13 - Prob. 13RQCh. 13 - Prob. 14RQCh. 13 - Prob. 15RQCh. 13 - List four uses for the data monitor function.Ch. 13 - Prob. 17RQCh. 13 - Prob. 18RQCh. 13 - Prob. 19RQCh. 13 - Prob. 20RQCh. 13 - Prob. 21RQCh. 13 - Prob. 22RQCh. 13 - Prob. 23RQCh. 13 - Prob. 24RQCh. 13 - Prob. 25RQCh. 13 - Prob. 26RQCh. 13 - Prob. 27RQCh. 13 - Prob. 28RQCh. 13 - Prob. 29RQCh. 13 - Prob. 30RQCh. 13 - Prob. 1PCh. 13 - A fuse is blown in an output module. Suggest two...Ch. 13 - Prob. 3PCh. 13 - Prob. 4PCh. 13 - Prob. 5PCh. 13 - Prob. 6PCh. 13 - A specific output is forced on, but the LED module...Ch. 13 - An electronic-based input sensor is wired to a...Ch. 13 - Prob. 9PCh. 13 - Prob. 11PCh. 13 - Prob. 12PCh. 13 - Prob. 13PCh. 13 - The program of Figure 13-39 is supposed to execute...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- There are many different process technologies used to achieve PLDs' programmable connections; provide six examples.arrow_forwardIntegrated circuits are fabricated from______________ materials that have ptoperties of a conductor and an insulator.arrow_forwardExplain Add Drop Multiplexers (ADM) and Terminal Multiplexers (TM), as well as their applications.arrow_forward
- Mode 9 design asynchronous direct reset up counter circuit with T Type ffs(clock, negative edge trigger)arrow_forwardThe output dc level of the output waveform 4 points for the bellow networkis .....ccccccecueecurnnnee %arrow_forward(Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)* Decoder 74hc138Or you can use 74HCxx versions.) Task 3: Design a Binary Ripple Carry Adder for 5+3 summation in BCDcoding system. Draw the the circuit diagram by using FullAdder Blocks. Simulate the circuit.arrow_forward
- a) Build your circuit Design and build a state machine that will control the transition between light settings of a traffic light unit as shown in Figure 1. The design should include 3 positive edge triggered D flip-flops. Use 1 flip-flop to control the on and off of a given light, and the state machine should switch from Red (100) -> Red and Amber (110) - > Green (001) -> Amber (010) and repeat the cycle again, with the transition table below.arrow_forwardDesign an appropriate combinational circuit that implements a digital system with the following output functions an AC remote: ON, OFF, MODE, SHIFT, FAN, SMART, SWING, ECO using a decoder.arrow_forwardWrite the difference between TTL and CMOS logic families according to the following table: SPECIFICATION TTL CMOS Components AND Basic Gate Noise Immunity Fan-out tp in ns Noise Margin Power/gate in mWatt Figure of Meritarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage LearningPrinciples of Information Systems (MindTap Course...Computer ScienceISBN:9781305971776Author:Ralph Stair, George ReynoldsPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning
Principles of Information Systems (MindTap Course...
Computer Science
ISBN:9781305971776
Author:Ralph Stair, George Reynolds
Publisher:Cengage Learning