Fundamentals of Geotechnical Engineering (MindTap Course List)
5th Edition
ISBN: 9781305635180
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 13, Problem 13.21P
(a)
To determine
Find the critical height of the slope in case (a).
(b)
To determine
Find the critical height of the slope in case (c).
(c)
To determine
Find the critical height of the slope in case (d).
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Q.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ,
ɣ = 20 kN/m3
, Ø = 33 ͦ,
and c’ = 47 kN/m2
. Find the height, H, such that a factor of safety, Fs = 3.1 is maintained
against sliding along the soil-rock interface.
For the infinite slope shown in Figure 15.46, determine the height, H, for critical equilibrium. Given: β = 27°, γ = 19.5 kN/m3, ϕ′ = 18°, and c′ = 35.9 kN/m3.
Figure 2 shows a slope with an inclination of : β = 58 ͦ. If AC represents a trial failure plane inclined at an angle θ = 32 ͦ with the horizontal, determine the factor of safety against sliding for the wedge ABC. Given: H = 6 m; ɣ = 19 kN/m3, Ø =21 ͦ, and c’= 38 kN/m2
Chapter 13 Solutions
Fundamentals of Geotechnical Engineering (MindTap Course List)
Ch. 13 - Prob. 13.1PCh. 13 - Prob. 13.2PCh. 13 - Prob. 13.3PCh. 13 - Prob. 13.4PCh. 13 - Prob. 13.5PCh. 13 - Prob. 13.6PCh. 13 - Prob. 13.7PCh. 13 - Prob. 13.8PCh. 13 - Prob. 13.9PCh. 13 - Prob. 13.10P
Ch. 13 - Prob. 13.11PCh. 13 - Prob. 13.12PCh. 13 - Prob. 13.13PCh. 13 - Prob. 13.14PCh. 13 - Prob. 13.15PCh. 13 - Prob. 13.16PCh. 13 - Prob. 13.17PCh. 13 - Prob. 13.18PCh. 13 - Prob. 13.19PCh. 13 - Prob. 13.20PCh. 13 - Prob. 13.21PCh. 13 - Prob. 13.22PCh. 13 - Prob. 13.23PCh. 13 - Prob. 13.25PCh. 13 - Prob. 13.26PCh. 13 - Prob. 13.27CTPCh. 13 - Prob. 13.28CTPCh. 13 - Prob. 13.29CTP
Knowledge Booster
Similar questions
- An infinite slope consists of bed rock inclined at 15° to the horizontal that is covered by 4 m (measured vertically) soil with ?′=10?N/?2, ?′=24° and ?=19.0?N/?3.a. What is the factor of safety of this slope?b. If there is steady state seepage through the soil, with the water table coinciding with the ground level, what would be the factor of safety? Assume ?sat = 19.0?N/?3.arrow_forwardA cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the stability factor?arrow_forwardA 45° slope as shown in figure has been excavated to a depth of 6 m in a saturated clay having the following properties Cu= 50 kN/m², qu=0° and y = 19 kN/m³ Determine the factor of safety. [Take area of wedge = 39 m²]arrow_forward
- 3. An infinite slope has shear strength parameters at the interface: c = 30 kPa, φ = 30°, γ = 17 kN/m3 (Assume 1 m strip perpendicular to the paper and 1 m strip along the inclination of the infinite slope). a. If H = 5 m, and β = 20°, find the sliding force. b. If H = 5 m, and β = 20°, find the force that resist sliding on the rock surface. c. If HCR = 8 m, find the minimum angle β so that the slope is stable.arrow_forwardA long slope is made up of a cohesionless soil with the internal friction angle of 34°. If the water table rises to the surface of the slope, then determine the maximum possible value of the slope angle to get a factor of safety of 1.5. Take saturated unit weight as 18 kN/m3 and the unit weight of water as 10 kN/m3.arrow_forwardGiven an infinite slope with the following properties: γ = 17 kN/m3, H = 5 m, β = 34°, φ = 25° and c = 20 kPa. a. Determine the normal stress. b. Determine the shear stress. c. Determine the factor of safety.arrow_forward
- A cut slope was excavated in saturated clays as shown in the figure. The soil has a unit weight of 17 kN/m³ and an undrained shear strength cᵤ = 20 kPa. The slope make an angle of 60° with the horizontal. Assume stability number m = 0.185. Slope failure occurs along the plane AC with BC = 8 m. Which of the following most nearly gives the maximum depth in meters up to which the cut could be made?arrow_forwardQ.1. Refer to the infinite slope shown in Figure 1. Given: β = 19 ͦ, ɣ = 20 kN/m3 , Ø = 33 ͦ, and c’ = 47 kN/m2 . Find the height, H, such that a factor of safety, Fs = 3.1 is maintained against sliding along the soil-rock interface. Also Determine the thrust on the wall if the water table rises to a level 2 m below the surface of the sand. The saturated unit weight of the sand is 20 kN/m3 .arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning