EP ENGINEERING FUNDAMENTALS-MINDTAP
5th Edition
ISBN: 9781305499508
Author: MOAVENI
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 13, Problem 3P
An elevator has a rated capacity of 2200 lb. It can transport people at the rated capacity between the first and the fifth floors, with a vertical distance of 15 ft between each floor, in 7 s. Estimate the power requirement for such an elevator.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Oil is being pumped from a truck to a tank 10 ft higher than the truck through a 2 in. galvanized pipeline 100 ft long. If the pressure of the discharge side of the pump is 15 psi, at what rate in gpm is oil flowing through the pipe? The oil has a specific gravity of 0.92 at the temperature of the pipe.
Water at 50°F is pumped from a lake at 750 gpm through a length of 3-inch schedule 40 commercial steel pipe as shown below. The inlet to the pipe is eight feet below the surface of the lake. A 25-HP gasoline engine drives the pump and the pump has an efficiency of 80%
What is the Reynolds number in the pipe? Is the flow laminar or turbulent?
What is the head added to the water by the pump?
What is the head loss due to pipe friction?
Determine the work done by an electric motor lifting an elevator weighing 4 kN through five floors; assume a distance of 3 m between each floor. Compute the power requirements for the motor to go from the first to the fifth floor ina. 5 sb. 8 sExpress your results in watts .
Chapter 13 Solutions
EP ENGINEERING FUNDAMENTALS-MINDTAP
Ch. 13.2 - Prob. 1BYGCh. 13.2 - Prob. 2BYGCh. 13.2 - Prob. 3BYGCh. 13.2 - Prob. 4BYGCh. 13.2 - Prob. 5BYGCh. 13.2 - Prob. BYGVCh. 13.4 - Prob. 1BYGCh. 13.4 - Prob. 2BYGCh. 13.4 - Prob. 3BYGCh. 13.4 - Prob. 4BYG
Ch. 13.4 - Prob. BYGVCh. 13.5 - Prob. 1BYGCh. 13.5 - Prob. 2BYGCh. 13.5 - Prob. 3BYGCh. 13.5 - Prob. 4BYGCh. 13.5 - Prob. 5BYGCh. 13.5 - Prob. BYGVCh. 13 - Prob. 1PCh. 13 - Prob. 2PCh. 13 - An elevator has a rated capacity of 2200 lb. It...Ch. 13 - Prob. 4PCh. 13 - Prob. 5PCh. 13 - Prob. 6PCh. 13 - Prob. 7PCh. 13 - Prob. 8PCh. 13 - Prob. 9PCh. 13 - Prob. 10PCh. 13 - Prob. 12PCh. 13 - Prob. 14PCh. 13 - Prob. 15PCh. 13 - Prob. 16PCh. 13 - Prob. 17PCh. 13 - Prob. 18PCh. 13 - Prob. 19PCh. 13 - Prob. 20PCh. 13 - Prob. 22PCh. 13 - Prob. 23PCh. 13 - Prob. 24PCh. 13 - Prob. 25PCh. 13 - Prob. 26P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A water tower that is 90 ft high provides water to a residential subdivision. The water main from the tower to the subdivision is 6 in. sch 40 steel, 3 miles long. If each house uses a maximum of 50 gal/h (at peak demand) and the pressure in the water main is not to be less than 30 psig at any point, how many homes can be served by the water main? Following are the number of valves and fittings: 2 standard 90-degree elbows Two completely open valves, one after the tank and the other before exiting the water main 29 standard coupling (K= 0.04) You noticed that the current piping system, which is above the ground, is vulnerable to tampering. Two couplings and two standard 90-degree elbows would be required if the water main was buried 6 feet underground. Will you be able to serve the same number of households as you did previously? Why? Please start by stating all of your assumptions and design considerations. Tips: Solve both conditions Underground and groundarrow_forwardWater is pumped thru a vertical 50mm new galvanized-iron pipe to an elevated tank on the roof of a building. The pressure on the discharge side of the pump is 1400kpa. What pressure can be expected at a point in the pipe 75mm above the pump when the flow is 9 liters/se?arrow_forwardIf you have 10 pumps of 30 HP each + 5 standby, responsible for elevating water from a ground tank to the top of a building through a pipe of 0.2 meters diameter, 0.1 friction factor and 250 meters length with a velocity of 1.2 m/s. Calculate the height of the building.arrow_forward
- Water enters and leaves a pump in pipelines of the same diameter and approximately the same elevation. If the pressure on the inlet side of the pump is 30 kPa and a pressure of 500 kPa is desired for the water leaving the pump, what is the head that must be added by the pump, and what is the power delivered to the fluid?arrow_forwardPropane is flowing in a 4-inch schedule 40 steel pipe at the minimum rate for which the flow is turbulent. Calculate the energy loss per 50 feet of pipe. Use Moody's diagram.arrow_forwardA 60 kg woman rides a 7 kg bicyle up a 3% grade at a constant speed of 2m/sec. Find the power that must be developed by the woman?arrow_forward
- A mall escalator is designed to move 50 people, 75 kg each, at a constant speed of 0.6 m/sec at 45o slope. Determine the minimum power input needed to drive this escalator. What would your answer be if the escalator velocity were to be doubled?arrow_forwardA pump lifts 60°F water from a stream to a reservoir whose surface is an unknown distance above the free surface of the stream. The suction pipe (from the stream to the pump) is 250 ft of 8-in Schedule 40 steel pipe, while the discharge pipe (from the pump to the reservoir) is 2250 ft of 8-in Schedule 40 PVC (plastic) pipe. The pump consumes 150 hp and has an estimated efficiency of 85%. The suction inlet of the pump is located 2.5 ft below the surface of the stream, while the discharge port of the pump is located at the same elevation as the surface of the stream. A differential manometer connected to the suction and discharge sides of the pump measures a pressure difference of 128 psi. Consider the friction loss in the piping (using the Darcy-Weisbach equation), but neglect other (minor) losses. Flow Reservoir Pump 2.5 ft Streamarrow_forwardIf the velocity of water is 8m/s and the pressure is 140kPa on the discharge side of a pump. How much power (in horsepower) is required to drive it if the diameter of the suction side is 600mm? If the pump is rated at 190hp, what is the efficiency of the pump neglecting energy losses in the system? Use diameter of pipe on discharge side equal to 50cm and the pressure on the suction side of the pump is 90kPa.arrow_forward
- Freight car A with a gross weight of 174000 Ib is moving along the horizontal track in a switching yard at 1.5 mi/hr. Freight car B with a gross weight of 157000 Ib and moving at 2.2 mi/hr overtakes car A and is coupled to it. Determine (a) the common velocity V of the two cars as they move together after being coupled and (b) the loss of energy |AE| due to the impact. 2.2 mi/hr 1.5 mi/hr В A Answers: (a) V = i mi/hr (b) ΔΕΙ- i ft-lbarrow_forwardGasoline (T=50 degrees F) is pumped from the gas tank of an automobile to the carburetor through a 1/4 in fuel line of drawn tubing 10 ft long. The line has five 90 degree smooth bends with an r/d of 6. The gasoline discharges through a 1/32 in jet in the carburetor to a pressure of 14 psia. The pressure in the tank is 14.7 psia. The pump is 80% efficient. What power must be supplied to the pump if the automobile is consuming fuel at a rate of 0.12 gpm. S=0.68, 2ft Pump 1/4 in line (ID) Carburetor tularrow_forwardCalculate the stopping sight disance for a design speed of 1000 kmph. Take the total reaction time 2.5 secs and the coefficient of friction = 0.35arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning
What Is A Construction Takeoff? | Are They Still Necessary In Quantity Surveying?; Author: Metroun Quantity Surveying;https://www.youtube.com/watch?v=uTWoDPtcOjg;License: Standard Youtube License