PROGRAMMABLE LOGIC CONTROLLERS (LOOSE PA
5th Edition
ISBN: 9781264206216
Author: Petruzella
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Question
Chapter 13, Problem 3P
Program Plan Intro
Programmable Logic Controller (PLC):
- PLC is a specialized computer used in industrial segments to control machines and process.
- PLC is program that consists of a set of instructions which resembles the controlling functions needed to perform specific tasks.
- The function of PLC is similar to that of a relay and hence, in an industrial segment a relay is greatly replaced by a suitable PLC.
- When compared to general Personal Computer (PC), a PLC is available in small and tiny sizes.
- The basic architecture of a PLC consists of an input-output interface module and a small Central Processing Unit (CPU) that runs by controlling
programming language.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Describe How a Time-driven sequence PLC program operates.
Design a PLC program and prepare a typical I/O
connection diagram and ladder logic program for
the following motor control specifications:
• Three starters are to be wired so that each starter
is operated from its own start/stop pushbutton
station.
• A master stop station is to be included that will
trip out all starters when pushed.
What is the difference between modes of operation (run,prog,rem)in plc
Chapter 13 Solutions
PROGRAMMABLE LOGIC CONTROLLERS (LOOSE PA
Ch. 13 - Prob. 1RQCh. 13 - Prob. 2RQCh. 13 - Prob. 3RQCh. 13 - List three potential noise-generating inductive...Ch. 13 - Prob. 5RQCh. 13 - Prob. 6RQCh. 13 - Prob. 7RQCh. 13 - Under what condition can a ground loop circuit be...Ch. 13 - Prob. 9RQCh. 13 - What operating state will cause an inductive load...
Ch. 13 - Prob. 11RQCh. 13 - Prob. 12RQCh. 13 - Prob. 13RQCh. 13 - Prob. 14RQCh. 13 - Prob. 15RQCh. 13 - List four uses for the data monitor function.Ch. 13 - Prob. 17RQCh. 13 - Prob. 18RQCh. 13 - Prob. 19RQCh. 13 - Prob. 20RQCh. 13 - Prob. 21RQCh. 13 - Prob. 22RQCh. 13 - Prob. 23RQCh. 13 - Prob. 24RQCh. 13 - Prob. 25RQCh. 13 - Prob. 26RQCh. 13 - Prob. 27RQCh. 13 - Prob. 28RQCh. 13 - Prob. 29RQCh. 13 - Prob. 30RQCh. 13 - Prob. 1PCh. 13 - A fuse is blown in an output module. Suggest two...Ch. 13 - Prob. 3PCh. 13 - Prob. 4PCh. 13 - Prob. 5PCh. 13 - Prob. 6PCh. 13 - A specific output is forced on, but the LED module...Ch. 13 - An electronic-based input sensor is wired to a...Ch. 13 - Prob. 9PCh. 13 - Prob. 11PCh. 13 - Prob. 12PCh. 13 - Prob. 13PCh. 13 - The program of Figure 13-39 is supposed to execute...
Knowledge Booster
Similar questions
- MENG444 Programmable language controller Please help me in 3 and 4 ???arrow_forwardanswer this question,pleasearrow_forward5 lamps are lit at intervals of 2 seconds with the start button. When all 5 lamps are lit, it waits for 5 seconds and continues to light up with 2 second intervals from the 1st lamp. If sensor 1 is active while lamp 1 is on, lamp 3 will continue to operate as above, without lamp number 2 turning on. with stop buttonlamps will be turned off at any time.draw the plc ladder diagram accordingly.arrow_forward
- PLCs use two basic types of instructions: contacts coilsDifferentiate the two types of instruction.arrow_forwardWhat is considered as a proper grounding system? a. None of the choices O b. All of the choices OC. Provides a high impedance path to earth ground O d. The complete PLC installation are all connected to a single low impedance ground e. The grounding path must be soldered to the PLC installationarrow_forwardPlease give the correct answer, else I dislikearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning