Physics for Scientists and Engineers with Modern Physics
4th Edition
ISBN: 9780131495081
Author: Douglas C. Giancoli
Publisher: Addison-Wesley
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 13, Problem 65P
(I) Engine oil (assume SAE 10, Table 13–3) passes through a fine 1.80-mm-diameler tube that is 8.6 cm long. What pressure difference is needed to maintain a flow rate of 6.2 mL/min?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionChapter 13 Solutions
Physics for Scientists and Engineers with Modern Physics
Ch. 13.3 - Prob. 1AECh. 13.3 - A dam holds hack a lake that is 85 m deep at the...Ch. 13.7 - On the hydrometer of Example 1311, will the marks...Ch. 13.7 - Which of the following objects, submerged in...Ch. 13.7 - Which of the following objects, submerged in...Ch. 13.9 - As water in a level pipe passes from a narrow...Ch. 13.10 - Return to Chapter-Opening Question 2, page 339,...Ch. 13 - If one material has a higher density than another,...Ch. 13 - Airplane travelers sometimes note that their...Ch. 13 - The three containers in Fig. 1343 are filled with...
Ch. 13 - Consider what happens when you push both a pin and...Ch. 13 - A small amount of water is boiled in a 1-gallon...Ch. 13 - Prob. 6QCh. 13 - An ice cube floats in a glass of water filled to...Ch. 13 - Will an ice cube float in a glass of alcohol? Why...Ch. 13 - A submerged can of Coke will sink, but a can of...Ch. 13 - Why dont ships made of iron sink?Ch. 13 - Explain how the tube in Fig. 1344, known as a...Ch. 13 - A barge filled high with sand approaches a low...Ch. 13 - Explain why helium weather balloons, which are...Ch. 13 - A row boat floats in a swimming pool, and the...Ch. 13 - Will an empty balloon have precisely the same...Ch. 13 - Why do you float higher in salt water than in...Ch. 13 - If you dangle two pieces of paper vertically, a...Ch. 13 - Why does the stream of water from a faucet...Ch. 13 - Prob. 19QCh. 13 - A tall Styrofoam cup is filled with water. Two...Ch. 13 - Why do airplanes normally lake off into the wind?Ch. 13 - Two ships moving in parallel paths close to one...Ch. 13 - Prob. 23QCh. 13 - Prob. 24QCh. 13 - (I) The approximate volume of the granite monolith...Ch. 13 - (I) What is the approximate mass of air in a...Ch. 13 - (I) If you tried to smuggle gold bricks by filling...Ch. 13 - (I) State your mass and then estimate your volume....Ch. 13 - (II) A bottle has a mass of 35.00g when empty and...Ch. 13 - (II) If 5.0L of antifreeze solution (specific...Ch. 13 - Prob. 7PCh. 13 - (I) Estimate the pressure needed to raise a column...Ch. 13 - (I) Estimate the pressure exerted on a floor by...Ch. 13 - (I) What is the difference in blood pressure...Ch. 13 - (II) How high would the level be in an alcohol...Ch. 13 - (II) In a movie, Tarzan evades his captors by...Ch. 13 - (II) The maximum gauge pressure in a hydraulic...Ch. 13 - (II) The gauge pressure in each of the four tires...Ch. 13 - (II) (a) Determine the total force and the...Ch. 13 - (II) A house at the bottom of a hill is fed by a...Ch. 13 - (II) Water anti then oil (which dont mix) are...Ch. 13 - (II) In working out his principle, Pascal showed...Ch. 13 - (II) What is the normal pressure of the atmosphere...Ch. 13 - (II) A hydraulic press for compacting powdered...Ch. 13 - (II) An open-tube mercury manometer is used to...Ch. 13 - (III) A beaker of liquid accelerates from rest, on...Ch. 13 - (III) Water stands at a height h behind a vertical...Ch. 13 - (III) Estimate the density of the water 5.4 km...Ch. 13 - (III) A cylindrical bucket of liquid (density ) is...Ch. 13 - (I) What fraction of a piece of iron will he...Ch. 13 - (I) A geologist finds that a Moon rock whose mass...Ch. 13 - (II) A crane lifts the 16,000-kg steel hull of a...Ch. 13 - (II) A spherical balloon has a radius of 7.35 m...Ch. 13 - (II) A 74-kg person has an apparent mass of 54 kg...Ch. 13 - (II) What is the likely identity of a metal (see...Ch. 13 - (II) Calculate the true mass (in vacuum) of a...Ch. 13 - Prob. 33PCh. 13 - (II) A scuba diver and her gear displace a volume...Ch. 13 - (II) The specific gravity of ice is 0.917, whereas...Ch. 13 - (II) Archimedes principle can be used not only to...Ch. 13 - (II) (a) Show that the buoyant force FB on a...Ch. 13 - (II) A cube of side length 10.0 cm and made of...Ch. 13 - (II) How many helium-filled balloons would it take...Ch. 13 - Prob. 40PCh. 13 - (III) If an object floats in water, its density...Ch. 13 - (III) A 3.25-kg piece of wood (SG = 0.50) floats...Ch. 13 - (I) A 15-cm-radius air duct is used to replenish...Ch. 13 - Prob. 44PCh. 13 - (I) How fast does water flow from a hole at the...Ch. 13 - (II) A fish tank has dimensions 36 cm wide by 1.0...Ch. 13 - (II) What gauge pressure in the water mains is...Ch. 13 - Prob. 48PCh. 13 - (II) A 180-km/h wind blowing over the flat roof of...Ch. 13 - (II) A 6.0-cm-diameter horizontal pipe gradually...Ch. 13 - (II) Estimate the air pressure inside a category 5...Ch. 13 - (II) What is the lift (in newtons) due to...Ch. 13 - (II) Show that the power needed to drive a fluid...Ch. 13 - (II) Water at a gauge pressure of 3.8 atm at...Ch. 13 - (II) In Fig. 1355, take into account the speed of...Ch. 13 - (II) Suppose the top surface of the vessel in Fig....Ch. 13 - (II) You are watering your lawn with a hose when...Ch. 13 - (III) Suppose the opening in the tank of Fig. 1355...Ch. 13 - Prob. 59PCh. 13 - (III) (a) Show that the flow speed measured by a...Ch. 13 - Prob. 61PCh. 13 - (III) A fire hose exerts a force on the person...Ch. 13 - (II) A viscometer consists of two concentric...Ch. 13 - Prob. 64PCh. 13 - (I) Engine oil (assume SAE 10, Table 133) passes...Ch. 13 - Prob. 66PCh. 13 - (II) What diameter must a 15.5-m-long air duct...Ch. 13 - (II) What must be the pressure difference between...Ch. 13 - (II) Poiseuilles equation does not hold if the...Ch. 13 - Prob. 70PCh. 13 - (III) A patient is to be given a blood...Ch. 13 - (I) If the force F needed to move the wire in Fig....Ch. 13 - (I) Calculate the force needed to move the wire in...Ch. 13 - (II) The surface tension of a liquid can be...Ch. 13 - (III) Estimate the diameter of a steel needle that...Ch. 13 - (III) Show that inside a soap bubble, there must...Ch. 13 - (III) A common effect of surface tension is the...Ch. 13 - A 2.8-N force is applied to the plunger of a...Ch. 13 - Intravenous infusions are often made under...Ch. 13 - A beaker of water rests on an electronic balance...Ch. 13 - Estimate the difference in air pressure between...Ch. 13 - A hydraulic lift is used to jack a 920-kg car 42...Ch. 13 - When you ascend or descend a great deal when...Ch. 13 - Giraffes are a wonder of cardiovascular...Ch. 13 - Suppose a person can reduce the pressure in his...Ch. 13 - Airlines are allowed to maintain a minimum air...Ch. 13 - A simple model (Fig. 13-57) considers a continent...Ch. 13 - A ship, carrying fresh water to a desert island in...Ch. 13 - During ascent, and especially during descent,...Ch. 13 - A raft is made of 12 logs lashed together. Each is...Ch. 13 - Estimate the total mass of the Earths atmosphere,...Ch. 13 - Prob. 92GPCh. 13 - Four lawn sprinkler heads are fed by a...Ch. 13 - A bucket of water is accelerated upward at 1.8 g....Ch. 13 - The stream of water from a faucet decreases in...Ch. 13 - You need to siphon water from a clogged sink. The...Ch. 13 - An airplane has a mass of 1.7 106 kg, and the air...Ch. 13 - A drinking fountain shoots water about 14 cm up in...Ch. 13 - A hurricane-force wind of 200 km/h blows across...Ch. 13 - Blood from an animal is placed in a bottle 1.30 m...Ch. 13 - Prob. 101GPCh. 13 - Prob. 102GPCh. 13 - A two-component model used to determine percent...Ch. 13 - (III) Air pressure decreases with altitude. The...
Additional Science Textbook Solutions
Find more solutions based on key concepts
A. In the space below, sketch a possible ticker tape resulting from motion with varying speed and write a descr...
Tutorials in Introductory Physics
If acceleration is proportional to the net force or is equal to net force.
Conceptual Physics (12th Edition)
14. A rifle is aimed horizontally at a target 50 m away. The bullet hits the target 2.0 cm below the aim point....
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
A particles position as a function of time is given by x = x0 sint, where x0 and are constants, (a) Find expre...
Essential University Physics: Volume 1 (3rd Edition)
Determine the average density of Earth. What data did you use? What assumptions did you make?
College Physics
Write each number in decimal form.
38. 4.05 × 100
Applied Physics (11th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A 2.50-kg steel gasoline can holds 20.0 L of gasoline when full. What is the average density of gas can, taking into account be volume occupied by steel as well as by gasoline?arrow_forwardA fire hose has an inside diameter of 6.40 cm. Suppose such a hose caries a flow of 40.0 L/s starting at a gauge pressure of 1.62106 N/m2. The hose goes 10.0 m up a ladder to a nozzle having an inside diameter of 3.00 cm. Calculate the Reynolds numbers for flow in the fire hose and nozzle to show that flow in each must be turbulent.arrow_forwardUsing the equation of the previous problem, find the viscosity of motor oil in which a steel ball of radius 0.8 mm falls a terminal speed of 4.32 cm/s. The densities of the ball and the oil are 7.86 and 0.88 g/mL, respectively.arrow_forward
- Water supplied to a house by a water main has a pressure of 3.00105N/m2 early on a summer day when neighborhood use is low. This pressure produces a flow of 20.0 L/min through a garden hose. Later in the day, pressure at the exit of the water main and entrance to the house drops, and a flow of only 8.00 L/min is obtained through the same hose. (a) What pressure is now being supplied to the house, assuming resistance is constant? (b) By what factor did the flow rate be water main increase in order to cause this decrease in delivered pressure? The pressure at the entrance of the water main is 5.00105N/m2 , and the original rate was 200 L/min. (c) How many more users are there, assuming each would consume 20.0 L/min in be morning?arrow_forwardWill the same ship float higher in salt water than in freshwater? Explain you answer.arrow_forwardA small artery has a length of 1.1103m and a radius of 2.55105m . If the pressure drop across the artery is 1.3 kPa, what is the flow rate through artery? (Assume Eat the temperature 37°C)arrow_forward
- Check Your Understanding Would a hydraulic press still operate properly if a gas is used instead of a liquid?arrow_forwardLook back to figure 14.29. Answer the following two question. Why is poless than atmospheric? Why is pogreater than pi?arrow_forwardIf be pressure reading of your pitot tube is 15.0 mm Hg at a speed of 200 km/h, what will it be at 700 km/h at the same altitude?arrow_forward
- A frequency quoted rule of thumb aircraft design is that wings should produce about 1000 N of lift per square meter of wing. (The fact that a wing has a top and bottom surface does not double its area.) (a) At takeoff, an aircraft travels at 60.0 m/s, so that the air speed relative to the bottom of the wing is 60.0 m/s. Given be sea level density of air as 1.29kg/m3, how fast must it move over be upper surface to create the ideal lift? (b) How fast must air move over the upper surface at a cruising speed of 245 m/s and at an altitude where air density is one-fourth that at sea level? (Note that his not all of be aircraft's lift—some comes from be body of the plane, some from engine thrust, and so on. Furthermore, Bernoulli's principle gives approximate answer because flow over wing creates turbulence.)arrow_forwardIf the pressure reading of your pitot tube is 15.0 mm Hg at a speed of 200 km/h, what will it be at 700 km/h at the same altitude?arrow_forwardConcrete is pumped from a cement mixer to the place it is being lad, instead of being carried wheelbarrows. The flow rate is 200 L/min through a 50.0-m-long, 8.00-cm-diameter hose, and he pressure it the pump is 8.00106 N/m2. (a) Calculate the resistance of the hose. (b) What is the viscosity of the concrete, assuming the flow is laminar? (c) How much power is being supplied, assuming the point of use is at the same level as the pump? You may neglect the power supplied to increase be concrete's velocity.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegePrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
College Physics
Physics
ISBN:9781938168000
Author:Paul Peter Urone, Roger Hinrichs
Publisher:OpenStax College
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Fluids in Motion: Crash Course Physics #15; Author: Crash Course;https://www.youtube.com/watch?v=fJefjG3xhW0;License: Standard YouTube License, CC-BY