Bundle: Principles Of Foundation Engineering, 9th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
9th Edition
ISBN: 9781337947060
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 17, Problem 17.10P
To determine
Check the overall stability of the wall. Find the factor of safety against overturning, sliding, and bearing capacity failure.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A smooth rigid retaining wall of 6 m high carries a uniform surchargeload of 12 kN/m2. The backfill is clayey sand possessing the following properties. γ = 16.0 kN/m3 , φ = 25°, and c = 6.5 kN/m2 for a retaining wall system, the following data were available: (i) Height ofwall = 7 m. (ii) Properties of backfill: γd =16 kN/m3, φ = 35 ° (iii) Angleof wall friction, δ =20° (iv) Back of wall is inclined at 20° to the vertical(positive batter) (v) Backfill surface is sloping at 1:10. Find thefollowing(i) Active earth pressure(ii) Passive earth pressure
A cantilever retaining wall supports 2 layers of soil and surcharge as shown below. The layers have these properties:
Layer 1: 1.8m thick. γ = 17.4 kN/m3 and ϕ = 22 degrees
Layer 2: 4.2m thick. γsat = 18.1 kN/m3 and ϕ = 30 degrees
The angle of friction between the base and soil is 42 degrees. Unit weight of concrete is 23.6 kN/m3
What is the design moment (kNm / m) at the bottom of the stem?
None of the choices
819.98
478.88
363.00
299.30
Please answer this asap. For upvote. Thank you very much
Analyze the stability of the reinforced cantilever
retaining wall based on the three failure modes;
: Sliding
: Overturning
: Bearing Stress
1. Unit weight of soil Ys = 18.5 kN/m³
2. Unit weight of Conc Yc = 24 kN/m³
3. Internal friction angle = 30°
4. Coefficient of friction between soil and concrete
bass M = 0.35
%3D
5. Bearing capacity of soil = 150 kN/m2
o 45m
Soon
3.
0145m
2.am
Chapter 17 Solutions
Bundle: Principles Of Foundation Engineering, 9th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
Knowledge Booster
Similar questions
- Q4) for retaining wall shown in Figure No. 3. Find the following: 1 m+ SandSoil W1 y=18 kN/m3 D=30° 5.5 m Concrete W2 Yc=24 kN/m3 1 m Clay Soil Ca=60 kN/m2 p=0° B- 1-Width of base (B) if factor safety of sliding = factor safety of overturning 2-Find friction angle under base if factor safety of sliding = 1 and Ca=0arrow_forward6. Details of a retaining wall are shown in the figure below. The unit weight of the wall material is 23 kN/m³. Assume a reduction factor K = 2/3 to consider the cohesion and friction angle at the base slab. Check the stability of the wall in terms of overturning and sliding failure. Use Rankine's theory to compute the active earth pressure. Soil 2 Y2 = 17 kN/m³ 6.5 m Im 2 m <-1.5m - Yc = 23 kN/m³ c₂ = 10 kN/m² 92 = 25° a = 15⁰ Soil 1 Y₁ = 16 kN/m³ c₁ = 0 kN/m² P₁ = 30°arrow_forwardProblem 3: A vertical retaining wall 6 m high is supporting a horizontal backfill having a weight 16.5 kN/m and a saturated unit weight of 19 kN/m?. Angle of trictian of the backfill is 30. Ground water table is located 3 m below the ground surface. 1. Determine the at rest lateral earth force per meter length of the wall. 3.0 m 2. Determine the location of the resultant force. 3. Determine the at rest lateral earth force per meter length af the wall if it carries a surcharge of 50 kPa. 3.0 marrow_forward
- Determine the stability of the cantilever gravity retaining wall shown in figure below. The existing soil is a clay and the backfill is a coarse-grained soil. The base of the wall will rest on a 50-mm-thick, compacted layer of the backfill. The interface friction between the base and the compacted layer of backfill is 25.0°. Groundwater level is 8 m below the base. 1.0 m Batter 1:20 0.4 m 1.8 m 9, = 20 kPa 8⁰ Ysat = 18 kN/m³ cs = 25° 8 = 15⁰ Backfill Drainage blanket Y = 23.5 kN/m³ 3 m Existing soil 6.1 m 0.9 mi Ysat = 19 kN/m³ = 35° % = 25°arrow_forwardQ2 Rankine's lateral pressure distributions against the vertical wall are include the effect of a variety of water table elevations and multiple soil layers in the backfill. Figure Q2 shows a vertical retaining wall with a horizontal backfill, which may fail in active mode. The water table elevations in front of the wall and at the back of the wall are different. (a) (b) Calculate the lateral pressures act against the wall. Support the answer with relevant diagram. Determine the total thrust force or resultant force. Support the answer with relevant point of application.arrow_forwardGiven the cantilever gravity retaining wall supporting a backfill of coarse-grained soil as shown. Note: Neglect the passive force and the weight of the soil in front of the wallI. 9, = 18 kPa *** 0.5 m 8 Ysat =19 kN/m³ O = 25 6.3 m Backfill Drainage blanket 1.0 m Y. = 23,5 KN/m 0.9 m +1.8 m-+ 3 m 1) Determine the location of the resultant active force from the toe in m. 2) Calculate the total overturning moment in kN-m. 3) Determine the total righting moment in kN-m. 4) Calculate the Factor of Safety against overturning in kN-m.arrow_forward
- Soil with an internal angle of friction of 40° and a cohesion of 10 kPa is excavated to a depth of 6 m prior to the placement of a retaining wall. The stability of a trial wedge with a horizontal angle of 25° is being investigated. The soil above the wedge weighs 12 kN/m of wall. 12 kN/m 6 m as=25° What is most nearly the available shearing resistance along the indicated slip plane? O A. 70 kN/m B. 140 kN/m O C. 150 kN/m OD. 180 kN/marrow_forward15. A backfill of a retaining wall consists of y=19 kN/m³ which is 6 m high. Find the lateral earth pressure per meter length. Given coefficient of earth pressure at rest is 0.5. a) 43 kN/m² b) 57 kN/m² c) 48 kN/m² d) 76 kN/m²arrow_forwardDetermine the analytical embedment depth and the total wall depth for this conditions. Give the effect of sand friction angle on the analytical embedment depth and the maximum bending moment Surcharge Load = 10 kN/m2 0 1 2 3 4 5 6 LD 7 16 kN/m² (= 0 phi= 30 °arrow_forward
- 6. Details of a retaining wall are shown in the figure below. The unit weight of the wall material is 23 kN/m³. Assume a reduction factor K = 2/3 to consider the cohesion and friction angle at the base slab. Check the stability of the wall in terms of overturning and sliding failure. Use Rankine's theory to compute the active earth pressure. 6.5 m tu 1 2 m Yc = 23 kN/m³ 4 m -1.5m - Soil 2 Y2 = 17 kN/m³ ₂ = 10 kN/m² P2 = 25° a = 15⁰ Soil 1 Y₁ = 16 kN/m³ c₁ = 0 kN/m² 4₁ = 30°arrow_forwardA 6m retaining wall is supporting a soil with the following properties:Unit weight = 16 KN/cu.mAngle of internal friction = 25ºCohesion = 14 Kpaa. Assuming no tensile cracks occurs in the soil; determine its normal pressure acting at the back of the wall.b. If tensile crack occurs in the soil, calculate its active pressure acting on the wall.c. Find the location of tensile crack measured from the surface of horizontal backfill.arrow_forwardA retaining wall is shown below to support two layers of soil. fc' = 23 MPa and fy = 420 MPa. Use 28mm diameter bars for the transverse reinforcement and 12mm for the longitudinal reinforcement. The parameters per layer are given below: Surcharge = qs = 8.04 kPa. Layer 1: H1 = 1.96m. γ = 15.74 kN/m3. Φ = 21 degrees Layer 2: H2 = 4.98m. Gs = 2.64. e = 0.44. S = 23.32%. Φ = 31 degrees. What is the minimum wall thickness (mm)?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning