(III) In the process of taking a gas from state a to state c along the curved path shown in Fig. 19–32, 85 J of heat leaves the system and 55 J of work is done on the system. (a) Determine the change in internal energy. Eint, a – Eint, c (b) When the gas is taken along the path cda, the work done by the gas is W = 38 J. How much heat Q is added to the gas in the process cda? (c) If Pa = 2.2Pd, how much work is done by the gas in the process abc? (d) What is Q for path abc? (e) If Eint, a – Eint, b = 15 J, what is Q for the process be? Here is a summary of what is given:
Want to see the full answer?
Check out a sample textbook solutionChapter 19 Solutions
PHYSICS F/SCI.+ENGINEERS W/MOD.PHYSICS
Additional Science Textbook Solutions
Essential University Physics: Volume 1 (3rd Edition)
University Physics (14th Edition)
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Life in the Universe (4th Edition)
Modern Physics
Introduction to Electrodynamics
- In a diesel engine, the fuel is ignited without a spark plug. Instead, air in a cylinder is compressed adiabatically to a temperature above the ignition temperature of the fuel; at the point of maximum compression, the fuel is injected into the cylinder. Suppose that air at 20 C is taken into the cylinder at a volume V1 and then compressed adiabatically and quasi-statically to a temperature of 600 C and a volume V2 . If =1.4 , what is the ratio V1/V2 ? (Note: static. In an operating diesel engine, the compression is not quasi-arrow_forwardCompare the charge in internal energy of an ideal gas for a quasi-static adiabatic expansion with that for a quasi-static isothermal expansion. What happens to the temperature of an ideal gas in an adiabatic expansion?arrow_forwardA cylinder containing three moles of a monatomic ideal gas is heated at a constant pressure of 2 atm. The temperature of the gas changes from 300 K to 350 K as a result of the expansion. Find work done (a) on the gas; and (b) by the gas.arrow_forward
- A mole of ideal monatomic gas at 0 and 1.00 atm is warmed up to expand isobarically to triple its volume. How much heat is transferred during the process?arrow_forwardTwo moles of nitrogen gas, with =7/5 for ideal diatomic gases, occupies a volume of 102 m3 in an insulated cylinder at temperature 300 K. The gas is adiabatically and reversibly compressed to a volume of 5 L. The piston of the cylinder is locked in its place, and the insulation around the cylinder is removed. The heat-conducting cylinder is then placed in a 300-K bath. Heat from the compressed gas leaves the gas, and the temperature of the gas becomes 300 K again. The gas is then slowly expanded at the fixed temperature 300 K until the volume of the gas becomes 102 m3, thus making a complete cycle for the gas. For the entire cycle, calculate (a) the work done by the gas, (b) the heat into or out of the gas, (c) the change in the internal energy of the gas, and (d) the change in entropy of the gas.arrow_forwardIn a quasi-static isobaric expansion, 500 J of work are done by the gas. The gas pressure is 0.80 atm and it was originally at 20.0 L. If the internal energy of the gas increased by 80 J in the expansion, how much heat does the gas absorb?arrow_forward
- When 400 J of heat are slowly added to 10 mol of an ideal monatomic gas, its temperature rises by 10 . What is the work done on the gas?arrow_forwardIt is found that, when a dilute gas expands quasi-statically from 0.50 to 4.0 L, it does 250 J of work. Assuming that the gas temperature remains constant at 300 K, how many moles of gas are present?arrow_forwardThe energy output of a heat pump is greater than the energy used to operate the pump. Why doesn't this statement violate the first law of thermodynamics?arrow_forward
- A sealed, rigid container of 0.560 mol of an unknown ideal gas at a temperature of 30.0 is cooled to 40.0 . In the process, 980 J of heat are removed from the gas. Is the gas monatomic, diatomic, or polyatomic?arrow_forwardIn an adiabatic process, oxygen gas in a container is compressed along a path that can be described by the following pressure in atm as a function of volume V, with V0=1L:P=(3.0atm)(V/V)1.2 . The initial and final volumes during the process were 2 L and 1.5 L, respectively. Find the amount of work done on the gas.arrow_forwardAn ideal diatomic gas at 80 K is slowly compressed adiabatically to one-third its original volume. What is its final temperature?arrow_forward
- Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning