Concept explainers
Consider an aluminum pan used to cook stew on top of an electric range. The bottom section of the pan is
The electric heating unit on the range top consumes 900 W of power during cooking, and 90 percent of the heat generated in the heating element is transferred to the pan. During steady operation, the temperature of the inner surface of the pan is measured to be
Want to see the full answer?
Check out a sample textbook solutionChapter 2 Solutions
HEAT+MASS TRANSFER:FUND...-CONNECTPLUS
- The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is increased by a gearbox that has an efficiency of 0.93. In turn, the gearbox output shaft drives an electric generator with an efficiency of 0.95. The cylindrical nacelle, which houses the gearbox, generator, and associated equipment, is of length L = 6 m and diameter D = 3 m. If the turbine produces P = 2.5 MW of electrical power, and the air and surroundings temperatures are T = 25 oC and Tsur = 20 oC, respectively, determine the minimum possible operating temperature inside the nacelle. The emissivity of the nacelle is 0.83, and the convective heat transfer coefficient is h = 35 W/m2 .K. The surface of the nacelle that is adjacent to the blade hub can be considered to be adiabatic, and solar irradiation may be neglected. Use Fin or N number of fins to reduce the Ts of the nacelle less than 143 oCarrow_forwardA 75-hp (shaft output) motor that has an efficiency of 91.0 percent is worn out and is replaced by a high-efficiency 75-hp motor that has an efficiency of 95.4 percent. Determine the reduction in the heat gain of the room due to higher efficiency under full-load conditions.arrow_forwardAn exercise room has 6 weight-lifting machines that have no motors and 7 treadmills each equipped with a 2.5-hp (shaft output) motor. The motors operate at an average load factor of 0.7, at which their efficiency is 0.77. During peak evening hours, all 12 pieces of exercising equipment are used continuously, and there are also two people doing light exercises while waiting in line for one piece of the equipment. Assuming the average rate of heat dissipation from people in an exercise room is 600 W, determine the rate of heat gain of the exercise room from people and the equipment at peak load conditions.arrow_forward
- A 10 hp fan is used in a room for circulation purposes. Assuming a sealed room. that is well insulated, determine the internal energy increase in Btu after 2 h of operation.arrow_forwardA student living in a 4-m x 6-m x 6-m dormitory room turns on her 150-W fan before she leaves the room on a summer day, hoping that the room will be cooler when she comes back in the evening. Assuming all the doors and windows are tightly closed and disregarding any heat transfer through the walls and the windows, determine the temperature in the room when she comes back 10 h later. Use specific heat values at room temperature, and assume the room to be at 100 kPa and 15°C in the morning when she leaves.arrow_forwardA student living in a 4-m x 6-m x 6-m dormitory room turns on her 150-W fan before she leaves the room on a summer day, hoping that the room will be cooler when she comes back in the evening. Assuming all the doors and windows are tightly closed and disregarding any heat transfer through the walls and the windows, determine the temperature in the room when she comes back 10 h later. Use specific heat values at room temperature, and assume the room to be at 100 kPa and 15°C in the morning when she leaves. ANS. 58.2 Carrow_forward
- An inventor claims to have developed a resistance heater that supplies 1.2 kWh of energy to a room for each kWh of electricity it consumes. Is this a reasonable claim, or has the inventor developed a perpetual-motion machine? Explain.arrow_forwardIf H is the work output of a heat engine and Q is the total heat input of an engine, then determine its thermal efficiency.arrow_forwardA cylindrical fuel rod (k = 30 W/m•K) of 2 cm in diameter is encased in a concentric tube and cooled by water. The fuel rod generates heat uniformly at a rate of 100 MW/m3, and the average temperature of the cooling water is 115°C with a convection heat transfer coefficient of 2500 W/m2.k. The operating pressure of the cooling water is such that the surface temperature of the fuel rod must be kept below 200°C to avoid the cooling water from reaching the critical heat flux (CHF). The critical heat flux is a thermal limit at which a boiling crisis can occur Determine the temperature at the surface of the rod. What can you do to lower the temperature aty the surface?arrow_forward
- A 300-ft-long section of a steam pipe whose outer diameter is 4 in passes through an open space at 50°F. The average temperature of the outer surface of the pipe is measured to be 280°F, and the average heat transfer coefficient on that surface is determined to be 6 Btu/h·ft2·°F. Determine (a) the rate of heat loss from the steam pipe and (b) the annual cost of this energy loss if steam is generated in a natural gas furnace having an efficiency of 86 percent, and the price of natural gas is $1.10/therm (1 therm = 100,000 Btu).arrow_forward10 m long pipe is being used to deliver steam through a processing plant. The inner radius of the pipe is r1 = 6 cm and the thickness of the pipe is 2 cm. Thermal conductivity k = 8 W/m⋅K and the average temperature steam flowing through the pipe is 160°C, the average convection heat transfer coefficient on the inner surface is given to be h = 20 W/m2⋅K. If the average temperature on the outer surfaces of the pipe is T2 = 70°C, (a) express the differential equation and the boundary conditions for steady operating conditions, (b) determine a relation for the variation of temperature in the pipe, and (c) evaluate the rate of heat loss (heat of conduction) from the steam through the pipe.arrow_forwardRequires Solution:Determine the power required providing 3 kw of colling at -10 degrees celcius while the surrounding air is at 24 degrees celcius. Answer: 0.39 kWarrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning