Fox And Mcdonald's Introduction To Fluid Mechanics
9th Edition
ISBN: 9781118921876
Author: Pritchard, Philip J.; Leylegian, John C.; Bhaskaran, Rajesh
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 2, Problem 77P
A supersonic aircraft travels at 2700 km/hr at an altitude of 27 km. What is the Mach number of the aircraft? At what approximate distance measured from the leading edge of the aircraft’s wing does the boundary layer change from laminar to turbulent?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
MA
The Mach number at the maximum velocity
point on the upper surface of an airfoil is 0.6 for the
freestream conditions of M = 0.5. Calculate the Mach
MA = 0.6
number at the same point for the freestream conditions
of M = 0.7. Use the convenient similarity rule.
М,- 0.7
M= 0.5
2. A particle is moving in air at sea level where the
temperature is 18°C. The two disturbance spheres
created by the particle at points A and B are shown in the
figure below. Determine the Mach no. and velocity of the
particle. (Hint: For different time intervals choose the first
sphere i.e. the bigger)
Ans: 0.5, 171 m-s?.
9m
3m
Particle <
With the aid of diagrams, explain what are Mach waves and how they are formed. From your understanding, how can the speed of a fighter aircraft model inside the wind tunnel can be estimatedby observing the Mach wave angle using optical measurements?
Chapter 2 Solutions
Fox And Mcdonald's Introduction To Fluid Mechanics
Ch. 2 - For the velocity fields given below, determine:...Ch. 2 - For the velocity fields given below, determine:...Ch. 2 - A viscous liquid is sheared between two parallel...Ch. 2 - For the velocity field V=Ax2yi+Bxy2j, where A = 2...Ch. 2 - A fluid flow has the following velocity...Ch. 2 - When an incompressible, nonviscous fluid flows...Ch. 2 - For the free vortex flow the velocities are t =...Ch. 2 - For the forced vortex flow the velocities are t =...Ch. 2 - A velocity field is specified as V=axyi+by2j,...Ch. 2 - A velocity field is given by V=ax3i+bxy3j, where a...
Ch. 2 - The velocity for a steady, incompressible flow in...Ch. 2 - The flow field for an atmospheric flow is given by...Ch. 2 - For the velocity field V=AxiAyj,, where A = 2s 1....Ch. 2 - A velocity field in polar coordinates is given...Ch. 2 - The flow of air near the Earths surface is...Ch. 2 - A velocity field is given by V=aytibxj, where a =...Ch. 2 - Air flows downward toward an infinitely wide...Ch. 2 - Consider the flow described by the velocity field...Ch. 2 - Consider the velocity field V = axi + by(1 + ct)...Ch. 2 - Consider the flow field given in Eulerian...Ch. 2 - A velocity field is given by V=axti+byj, where A =...Ch. 2 - Consider the garden hose of Fig. 2.5. Suppose the...Ch. 2 - Consider the velocity field of Problem 2.18. Plot...Ch. 2 - Streaklines are traced out by neutrally buoyant...Ch. 2 - Consider the flow field V=axti+bj, where a = 1/s2...Ch. 2 - A flow is described by velocity field V=ay2i+bj,...Ch. 2 - Tiny hydrogen bubbles are being used as tracers to...Ch. 2 - A flow is described by velocity field V=ai+bxj,...Ch. 2 - A flow is described by velocity field V=ayi+btj,...Ch. 2 - A flow is described by velocity field V=ati+bj,...Ch. 2 - The variation with temperature of the viscosity of...Ch. 2 - The variation with temperature of the viscosity of...Ch. 2 - Some experimental data for the viscosity of helium...Ch. 2 - The velocity distribution for laminar flow between...Ch. 2 - What is the ratio between the viscosities of air...Ch. 2 - Calculate velocity gradients and shear stress for...Ch. 2 - A very large thin plate is centered in a gap of...Ch. 2 - A female freestyle ice skater, weighing 100 lbf,...Ch. 2 - A block of mass 10 kg and measuring 250 mm on each...Ch. 2 - A 73-mm-diameter aluminum (SG = 2.64) piston of...Ch. 2 - A vertical gap 25 mm wide of infinite extent...Ch. 2 - A cylinder 8 in. in diameter and 3 ft long is...Ch. 2 - Crude oil at 20C fills the space between two...Ch. 2 - The piston in Problem 2.40 is traveling at...Ch. 2 - A block of mass M slides on a thin film of oil....Ch. 2 - A block 0.1 m square, with 5 kg mass, slides down...Ch. 2 - A torque of 4 N m is required to rotate the...Ch. 2 - A circular disk of diameter d is slowly rotated in...Ch. 2 - The fluid drive shown transmits a torque T for...Ch. 2 - A block that is a mm square slides across a flat...Ch. 2 - In a food-processing plant, honey is pumped...Ch. 2 - SAE 10W-30 oil at 100C is pumped through a tube L...Ch. 2 - The lubricant has a kinematic viscosity of 2:8105...Ch. 2 - Calculate the approximate viscosity of the oil....Ch. 2 - Calculate the approximate power lost in friction...Ch. 2 - Fluids of viscosities 1 = 0.1 Ns/m2 and 2 = 0.15...Ch. 2 - A concentric cylinder viscometer may be formed by...Ch. 2 - A concentric cylinder viscometer is driven by a...Ch. 2 - A shaft with outside diameter of 18 mm turns at 20...Ch. 2 - A shock-free coupling for a low-power mechanical...Ch. 2 - A proposal has been made to use a pair of parallel...Ch. 2 - The cone and plate viscometer shown is an...Ch. 2 - A viscometer is used to measure the viscosity of a...Ch. 2 - A concentric-cylinder viscometer is shown. Viscous...Ch. 2 - Design a concentric-cylinder viscometer to measure...Ch. 2 - A cross section of a rotating bearing is shown....Ch. 2 - Small gas bubbles form in soda when a bottle or...Ch. 2 - You intend to gently place several steel needles...Ch. 2 - According to Folsom [6], the capillary rise h...Ch. 2 - Calculate and plot the maximum capillary rise of...Ch. 2 - Calculate the maximum capillary rise of water...Ch. 2 - Calculate the maximum capillary depression of...Ch. 2 - Water usually is assumed to be incompressible when...Ch. 2 - The viscous boundary layer velocity profile shown...Ch. 2 - In a food industry process, carbon tetrachloride...Ch. 2 - What is the Reynolds number of water at 20C...Ch. 2 - A supersonic aircraft travels at 2700 km/hr at an...Ch. 2 - SAE 30 oil at 100C flows through a 12-mm-diameter...Ch. 2 - A seaplane is flying at 100 mph through air at...Ch. 2 - An airliner is cruising at an altitude of 5.5 km...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A spring of stiffness k = 500 N/m is mounted against the 10-kg block. If the block is subjected to the force of...
Engineering Mechanics: Dynamics (14th Edition)
Figure 3.23 shows a closed tank that contains gasoline floating on water. Calculate the air pressure above the ...
Applied Fluid Mechanics (7th Edition)
Do the previous problem if the water is heated to the boiling point at 200 kPa.
Fundamentals Of Thermodynamics
Replace the two forces and one couple acting on the rigid pipe frame by their equivalent resultant force R acti...
Engineering Mechanics: Statics
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Which type of oxyfuel flame is most commonly used?
DeGarmo's Materials and Processes in Manufacturing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Consider a cone at zero angle of attack in a hypersonic flow. (Hypersonic flow is very high-speed flow, generally defined as any flow above a Mach number of 5.) The half-angle of the cone is θc, as shown inthe figure. An approximate expression for the pressure coefficient on the surface of ahypersonic body is given by the newtonian sine-squared law : Cp = 2 sin2 θcNote that Cp, hence, p, is constant along the inclined surface of the cone. Along the base of the body, we assume that p = p∞. Neglecting the effect of friction, obtain an expression for the drag coefficient of the cone, where CD is based on the area of the base Sb.arrow_forwardThe stagnation pressure in a Mach 2 wind tunnel operating with air is 750 kPa. A 4-cm-diameter sphere positioned in the wind tunnel has a drag coefficient of 0.95. Calculate the drag force on the sphere. FD Narrow_forwardOn March 16, 1990, an Air Force SR-71 set a new continental speedrecord, averaging a velocity of 2112 mi/h at an altitude of 80,000 ft.Calculate the temperature (in degrees Fahrenheit) at a stagnation point onthe vehicle.arrow_forward
- The shock waves on a vehicle in supersonic flight cause a component ofdrag called supersonic wave drag Dw. Define the wave-drag coefficient asCD,w = Dw/q∞S, where S is a suitable reference area for the body. Insupersonic flight, the flow is governed in part by its thermodynamicproperties, given by the specific heats at constant pressure cp and atconstant volume cv. Define the ratio cp/cv ≡ γ . Using Buckingham’spi theorem, show that CD,w = f (M∞, γ ). Neglect the influence of friction.arrow_forwardDetermine the lift coefficient of a supersonic aerofoil, approximated by a flat plate. It is flying at Ma 3.4 at an angle of attack of 7°. Assume the fluid to be air as a perfect gas with k=1.4.arrow_forwardHelp me solve this problem of dynamic gases Choose the correctarrow_forward
- I need the answer quicklyarrow_forwardA particle is moving in air at sea level where the temperature is 15°c. The two disturbance spheres created by the particle at points A and B are shown in the figure below. Determine the Mach number and the velocity of particle. 6m; 3m particle FEnginee ineeringarrow_forwardA straight-tapered flying-wing aircraft has the following characteristics: span, 20 ft; area, 100 ft2 ; root chord, 6 ft; tip chord, 4 ft; leading-edge sweep angle, 40 deg; sweep angle of line of maximum thickness, 24 deg; and Airfoil NACA 2412. Determine the wing's lift-curve slope and induced drag k value. Assume the flight Mach number is 0.25 in standard sea-level conditions.arrow_forward
- Consider a 6,670-N airplane in level flight at 5,000 m altitude with a Mach number of 0.42. The area of the wing is 15 m2. Solve for the lift coefficient. Assume standard sea level condition. Hint: At level flight, lift is equal to weight.arrow_forwardAn airplane fl ies at 555 mi/h. At what altitude in the standardatmosphere will the airplane’s Mach number beexactly 0.8?arrow_forwardThe temperature of a flat plate is Tw = 3Te , where Te is the static temperature of the high Reynolds flow outside the boundary layer, parallel to the plate. What is the minimum value of mach number for the aerodynamic heating to become more relevant than the convective cooling for the plate?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License