Concept explainers
(a)
The voltage and current amplitudes for the light bulb connected to an ac generator.
Answer to Problem 80QAP
For the bulb connected to the ac generator, the voltage amplitude is found to be 13 V and the current amplitude is 1.53 A.
Explanation of Solution
Given:
Magnetic field applied
Number of turns
Length of a side of the square coil
Frequency of the generator
Resistance of the bulb
Formula used:
The voltage amplitude is given by the expression,
Here, A is the area of the square coil, given by,
Therefore,
The current amplitude is given by,
Calculation:
Substitute the known values of variables in equation (1) and calculate the voltage amplitude.
Calculate the current amplitude by substituting the value of R and the calculated value of
Conclusion:
Thus, for the bulb connected to the ac generator, the voltage amplitude is found to be 13 V and the current amplitude is 1.53 A.
(b)
The average rate at which heat is generated in the bulb connected to the ac generator.
Answer to Problem 80QAP
The average rate at which heat is generated in the bulb connected to the ac generator is 9.99 W.
Explanation of Solution
Given:
The current amplitude
Resistance of the bulb
Formula used:
The average rate at which heat is generated in the bulb is equal to the power dissipated by the bulb. This is given by,
Here,
Therefore,
Calculation:
Substitute the values of the variables in equation (3) and calculate the rate at which heat is generated in the bulb.
Conclusion:
Thus, the average rate at which heat is generated in the bulb connected to the ac generator is 9.99 W.
(c)
The energy consumed by the bulb every hour.
Answer to Problem 80QAP
The energy consumed by the bulb every hour is
Explanation of Solution
Given:
Average power
Time interval
Formula used:
The energy consumed by the bulb every hour is given by,
Calculation:
Substitute the values of variables in the formula and calculate the energy consumed in one hour.
Conclusion:
Thus, the energy consumed by the bulb every hour is
Want to see more full solutions like this?
Chapter 21 Solutions
COLLEGE PHYSICS,VOLUME 1
- A toroidal coil has a mean radius of 16 cm and a cross-sectional area of 0.25 cm2; it is wound uniformly with 1000 turns. A second toroidal coil of 750 turns is wound uniformly over the first coil. Ignoring the variation of the magnetic field within a toroid, determine the mutual inductance of the two coils.arrow_forwardA flat, square coil of 20 turns that has sides of length 15.0 cm is rotating in a magnetic field of strength 0.050 T. If tlie maximum emf produced in die coil is 30.0 mV, what is the angular velocity of the coil?arrow_forwardA 50-turn coil has a diameter of 15 cm. The coil is placed in a spatially uniform magnetic field of magnitude 0.50 T so that the face of the coil and the magnetic field are perpendicular. Find the magnitude of the emf induced in the coil if the magnetic field is reduced to zero uniformly in (a) 0.10 s, (b) 1.0 s, and (c) 60 s.arrow_forward
- Suppose that a rectangular toroid has 2000 windings and a self-inductance of 0.040 H. If h = 0.10 m, what is the current flowing through a rectangular toroid when the energy in its magnetic field is 2.0 × 10-6 J?arrow_forwardThe self-inductance and capacitance of an LC circuit e 0.20 mH and 5.0 pF. What is the angular frequency at which the circuit oscillates?arrow_forwardTo monitor the breathing of a hospital patient, a thin belt is girded around the patients chest as in Figure P20.21. The belt is a 200-turn coil. When the patient inhales, the area encircled by the coil increases by 39.0 cm2. The magnitude of Earths magnetic field is 50.0 T and makes an angle of 28.0 with the plane of the coil. Assuming a patient takes 1.80 s to inhale, find the magnitude of the average induced emf in the coil during that time. Figure P20.21arrow_forward
- Review. Figure P31.31 shows a bar of mass m = 0.200 kg that can slide without friction on a pair of rails separated by a distance = 1.20 m and located on an inclined plane that makes an angle = 25.0 with respect to the ground. The resistance of the resistor is R = 1.00 and a uniform magnetic field of magnitude B = 0.500 T is directed downward, perpendicular to the ground, over the entire region through which the bar moves. With what constant speed v does the bar slide along the rails?arrow_forwardIn Figure P20.65 the rolling axle of length 1.50 m is pushed along horizontal rails at a constant speed v = 3.00 m/s. A resist or R = 0.400 is connected to the rails at points a and b, directly opposite each other. (The wheels make good electrical contact with the rails, so the axle, rails, and R form a closed-loop circuit. The only significant resistance in the circuit is R.) A uniform magnetic field B = 0.800 T is directed vertically downward. (a) Find the induced current I in the resistor. (b) What horizontal force F is required to keep the axle rolling at constant speed? (c) Which end of the resistor, a or b. is at the higher electric potential? (d) Alter the axle rolls past the resistor, does the current in R reverse direction? Explain your answer. Figure P20.65arrow_forwardShow that Equation 32.28 in the text Ls Kirchhoffs loop rule as applied to the circuit in Figure P32.56 with the switch thrown to position b.arrow_forward
- A circular loop of wire with a radius of 4.0 cm is in a uniform magnetic field of magnitude 0.060 T. The plane of the loop is perpendicular to the direction of the magnetic field. In a time interval of 0.50 s, the magnetic field changes to the opposite direction with a magnitude of 0.040 T. What is the magnitude of the average emf induced in the loop? (a) 0.20 V (b) 0.025 V (c) 5.0 mV (d) 1.0 mV (e) 0.20 mVarrow_forwardWhen a wire carries an AC current with a known frequency, you can use a Rogowski coil to determine the amplitude Imax of the current without disconnecting the wire to shunt the current through a meter. The Rogowski coil, shown in Figure P23.8, simply clips around the wire. It consists of a toroidal conductor wrapped around a circular return cord. Let n represent the number of turns in the toroid per unit distance along it. Let A represent the cross-sectional area of the toroid. Let I(t) = Imax sin t represent the current to be measured. (a) Show that the amplitude of the emf induced in the Rogowski coil is Emax=0nAImax. (b) Explain why the wire carrying the unknown current need not be at the center of the Rogowski coil and why the coil will not respond to nearby currents that it does not enclose. Figure P23.8arrow_forwardA thin conducting bar (60.0 cm long) aligned in the positive y direction is moving with velocity v=(1.25m/s)i in a region with a spatially uniform 0.400-T magnetic field directed at an angle of 36.0 above the xy plane. a. What is the magnitude of the emf induced along the length of the moving bar? b. Which end of the bar is positively charged?arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning