Fundamentals Of Physics - Volume 1 Only
11th Edition
ISBN: 9781119306856
Author: Halliday
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 26, Problem 16P
Copper and aluminium are being considered for a high-voltage transmission line that must carry a current of 60.0 A. The resistance per unit length is to be 0.150 Ω/km. The densities of copper and aluminum are 8960 and 2600 kg/m3, respectively. Compute (a) the magnitude J of the current density and (b) the mass per unit length λ for a copper cable and (c) J and (d) λ for an aluminium cable.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Copper and aluminum are being considered for a high-voltage transmission line that must carry a current of 60.0 A. The resistance per unit length is to be 0.150 /km.The densities of copper and aluminum are 8960 and 2600 kg/m3, respectively. Compute (a) the magnitude J of the current density and (b) the mass per unit length l for a copper cable and (c) J and (d) l for an aluminum cable.
1) A copper cable is designed to carry a current of 330 A with a power loss of 2.00 W/m. What is the required radius of this cable? pcopper = 1.7 x 10-8
0.0103 m
0.0009 m
0.0446 m
0.0172 m
2) An electric utility company supplies a customer’s house from the main power lines (120 V) with two copper wires, each of which is 110.0 m long and has a resistance of 0.12 per 400 m. Find the power delivered to the customer and assume that a load current at the customer’s house is 140 A.
32,340 W
16,800 W
16,153 W
15,506 W
A high voltage transmission line of diameter 2.55 cm and length 3.42167 km carries a steady current of 2 x103 A. If the conductor is copper with a free charge density of 7 x 1028 electrons/m3, how long (in seconds ) does it take one electron to travel the full length of the cable? (e = 1.6 x 10−19 C).For this problem use scientific/exponential notation to represent your answer.
Chapter 26 Solutions
Fundamentals Of Physics - Volume 1 Only
Ch. 26 - Figure 26-15 shows cross sections through three...Ch. 26 - Figure 26-16 shows cross sections through three...Ch. 26 - Figure 26-17 shows a rectangular solid conductor...Ch. 26 - Figure 26-18 shows plots of the current i through...Ch. 26 - Figure 26-19 shows four situations in which...Ch. 26 - In Fig. 26-20, a wire that carries a current...Ch. 26 - Figure 26-21 gives the electric potential Vx...Ch. 26 - The following table give the lengths of three...Ch. 26 - Prob. 9QCh. 26 - Three wires, of the same diameter, are connected...
Ch. 26 - Figure 26-23 gives, for three wires of radius R,...Ch. 26 - During the 4.0 min a 5.0 A current is set up in a...Ch. 26 - An isolated conducting sphere has a 10 cm radius....Ch. 26 - A charged belt, 50 cm wide, travels at 30 m/s...Ch. 26 - The United States National Electric Code, which...Ch. 26 - SSM WWW A beam contains 2.0 108 doubly charged...Ch. 26 - A certain cylindrical wire carries current. We...Ch. 26 - A fuse in an electric circuit is a wire that is...Ch. 26 - Prob. 8PCh. 26 - The magnitude Jr of the current density in a...Ch. 26 - The magnitude J of the current density in a...Ch. 26 - What is the current in a wire of radius R = 3.40...Ch. 26 - Near Earth, the density of protons in the solar...Ch. 26 - Prob. 13PCh. 26 - A human being can be electrocuted if a current as...Ch. 26 - SSM A coil is formed by winding 250 turns of...Ch. 26 - Copper and aluminium are being considered for a...Ch. 26 - Prob. 17PCh. 26 - A wire 4.00 m long and 6.00 mm in diameter has a...Ch. 26 - SSM What is the resistivity of a wire of 1.0 mm...Ch. 26 - Prob. 20PCh. 26 - ILW A common flashlight bulb is rated at 0.30 A...Ch. 26 - Kiting during a storm. The legend that Benjamin...Ch. 26 - Prob. 23PCh. 26 - GO Figure 26-25a gives the magnitude Ex of the...Ch. 26 - SSM ILW A wire with a resistance of 6.0 is drawn...Ch. 26 - In Fig. 26-26a. a 9.00 V battery is connected to a...Ch. 26 - SSM WWW Two conductors are made of the same...Ch. 26 - GO Figure 26-27 gives the electric potential Vx...Ch. 26 - Prob. 29PCh. 26 - Prob. 30PCh. 26 - Prob. 31PCh. 26 - Prob. 32PCh. 26 - Prob. 33PCh. 26 - GO Figure 26-29 shows wire section 1 of diameter...Ch. 26 - GO In Fig. 26-30, current is set up through a...Ch. 26 - GO Swimming during a storm. Figure 26-31 shows a...Ch. 26 - Prob. 37PCh. 26 - In Fig. 26-32a, a 20 resistor is connected to a...Ch. 26 - A certain brand of hot-dog cooker works by...Ch. 26 - Thermal energy is produced in a resistor at a rate...Ch. 26 - SSM A 1220 V potential difference is applied to a...Ch. 26 - In Fig. 26-33, a battery of potential difference V...Ch. 26 - ILW An unknown resistor is connected between the...Ch. 26 - A student kept his 6.0 V, 7.0 W radio turned on at...Ch. 26 - SSM ILW A 1250 W radiant heater is constructed to...Ch. 26 - A copper wire of cross-sectional area 2.00 106 m2...Ch. 26 - A heating element is made by maintaining a...Ch. 26 - Exploding shoes. The rain-soaked shoes of a person...Ch. 26 - A 100 W lightbulb is plugged into a standard 120 V...Ch. 26 - GO The current through the battery and resistors 1...Ch. 26 - GO SSM WWW Wire C and wire D are made from...Ch. 26 - GO The current-density magnitude in a certain...Ch. 26 - A 120 V potential difference is applied to a space...Ch. 26 - Go Figure 26-36a shows a rod of resistive...Ch. 26 - SSM A Nichrome heater dissipates 500 W when the...Ch. 26 - Prob. 56PCh. 26 - An 18.0 W device has 9.00 V across it. How much...Ch. 26 - An aluminum rod with a square cross section is 1.3...Ch. 26 - A cylindrical metal rod is 1.60 m long and 5.50 mm...Ch. 26 - The chocolate crumb mystery. This story begins...Ch. 26 - SSM A steady beam of alpha particles q = 2e...Ch. 26 - A resistor with a potential difference of 200 V...Ch. 26 - A 2.0 kW heater element from a dryer has a length...Ch. 26 - cylindrical resistor of radius 5.0 mm and length...Ch. 26 - A potential difference V is applied to a wire of...Ch. 26 - The headlights of a moving car require about 10 A...Ch. 26 - A 500 W heating unit is designed to operate with...Ch. 26 - The copper windings of a motor have a resistance...Ch. 26 - How much electrical energy is transferred to...Ch. 26 - A caterpillar of length 4.0 cm crawls in the...Ch. 26 - Prob. 71PCh. 26 - A steel trolley-car rail has a cross-sectional...Ch. 26 - A coil of current-carrying Nichrome wire is...Ch. 26 - Prob. 74PCh. 26 - A certain x-ray tube operates at a current of 7.00...Ch. 26 - A current is established in a gas discharge tube...Ch. 26 - Prob. 77PCh. 26 - An insulating belt moves at speed 30 m/s and has a...Ch. 26 - In a hypothetical fusion research lab, high...Ch. 26 - When a metal rod is heated, not only its...Ch. 26 - A beam of 16 MeV deuterons from a cyclotron...Ch. 26 - A linear accelerator produces a pulsed beam of...Ch. 26 - An electric immersion heater normally takes 100...Ch. 26 - A 400 W immersion heater is placed in a pot...Ch. 26 - A 30 F capacitor is connected across a programmed...
Additional Science Textbook Solutions
Find more solutions based on key concepts
76 ** EST In the situation of Problem 4.75, estimate (a) the maximum speed of the book and (b) the clock readin...
College Physics
The ratio of the turns of turns on the primary coil to turns on the secondary coil in a transformer.
Physics (5th Edition)
31. Your forehead can withstand a force of about 6.0 kN before fracturing, while your cheekbone can withstand o...
Physics for Scientists and Engineers: A Strategic Approach with Modern Physics (4th Edition)
The newly discovered element .
Glencoe Physical Science 2012 Student Edition (Glencoe Science) (McGraw-Hill Education)
If one of three lamps blows out when connected in parallel, what happens to the current in the other two?
Conceptual Physics: The High School Physics Program
An a water counter flowing heat exchanger has one line with 2kg/s at 125kPa,1000K entering, and the a is leavin...
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A copper wire is dCu = 0.0500 cm in diameter, 3.00 m long, and has a charge carrier density of 8.50x10^28 electrons/m3. The copper wire is attached to an equal length of aluminum wire with diameter dAl = 0.0100 cm and charge carrier density of 6.02x10^28 electrons/m3. A current of 0.400 A flows through the copper wire. a. The ratio of current densities in the two wires, JCu/JAl is:___. b. The ratio of drift velocities in the two wires, vd–Cu/vd–Al is:____.arrow_forwardEnergy is to be transmitted over a pair of copper wires in a transmission line at the rate of 20.0 kW with only a 1.00% loss over a distance of 18.0 km at potential difference ΔVrms = 1.50 × 103 V between the wires. Assuming the current density is uniform in the conductors, what is the diameter required for each of the two wires?arrow_forwardThe magnitude J of the current density in a certain wire with a circular cross section of radius R = 2.21 mm is given by J = (3.18 × 108)r2, with J in amperes per square meter and radial distance r in meters. What is the current through the outer section bounded by r = 0.927R and r = R?arrow_forward
- A high voltage transmission line of diameter 3.73 cm and length 3.76189 km carries a steady current of 1.9 x103 A. If the conductor is copper with a free charge density of 6 x 1028 electrons/m3, how long (in seconds ) does it take one electron to travel the full length of the cable? (e = 1.6 x 10−19 C).For this problem use scientific/exponential notation to represent your answer. Eg., -0.0001 can be written as 1.0e-4 or as 1.0E-4. Spaces are not allowed.arrow_forwardThe magnitude J(r) of the current density in a certain cylindrical wire is given as a function of radial distance from the center of the wire’s cross section as J(r) = Br, where r is in meters, J is in amperes per square meter, and B =2.00 * 10^5 A/m3.This function applies out to the wire’s radius of 2.00 mm. How much current is contained within the width of a thin ring concentric with the wire if the ring has a radial width of 10.0 mm and is at a radial distance of 1.20 mm?arrow_forwardAn 8.00-ft extension cord has two 18-gauge copper wires, each having a diameter of 1.024 mm. At what rate is energy delivered to the resistance in the cord when it is carrying a current of (a) 1.00 A and (b) 10.0 A?arrow_forward
- Six copper wires are characterized by their dimensions and by the current they carry. Rank the wires in order of decreasing drift velocity. Use ">" or "=" symbols (a) diameter 4 mm, length 16 m, current 40 mA(b) diameter 2 mm, length 2 m, current 160 mA(c) diameter 1 mm, length 4 m, current 20 mA(d) diameter 1 mm, length 1 m, current 80 mA(e) diameter 2 mm, length 1 m, current 40 mA(f) diameter 2 mm, length 2 m, current 80 mAarrow_forwardA copper wire is carrying 5.0 A of current. Given that the electric field between the ends of the cable has a value of 0.75 V/m. (a) find the current density in the wire. (b) the drift speed of the mobile charges. (c) If a potential difference of 20.0 V is applied. Find the resistance, length and cross-sectional area of the cable. Note: the density of copper D=8960 kg/m3, and the molar mass of the copper is m=0.063 kg/mol. Assume each atom of contributes with one electron.arrow_forwardThree resistors connected in series carry currents labeled I1, I2, and I3, respectively. Which of the following expresses the total current, It, in the system made up of the three resistors in series? a It= I1 + I2 + I3 b It= (1I1 + 1/I2 + 1/I3) c It= I1 = I2 = I3 d It= (1I1 + 1/I2 + 1/I3)–1arrow_forward
- A high voltage transmission line with a diameter of 2 cm carries a steady current of 980 A. The conductor is copper with a free charge density of 8×1028 electrons/m3. If it takes 8×108 s for one electron to travel the full length of the cable, how long is the cable (in m)? (e = 1.6×10-19 C)arrow_forwardAt room temperature, what is the strength of the electric field in a 12 gauge copper wire (diameter 2.05 mm) that is needed to cause a 3.90 A current to flow? Use the resistivity at room temperature for copper ρ = 1.72×10−8 Ω⋅m. Express your answer with the appropriate units. What field would be needed if the wire were made of silver instead? Use the resistivity at room temperature for silver ρ = 1.47×10−8 Ω⋅m. Express your answer with the appropriate units.arrow_forwardYou connect a battery, resistor, and capacitor as in (Figure 1), where R = 14.0 Ω and C = 3.00 ×10^-6 F. The switch S is closed at t = 0. When the current in the circuit has magnitude 3.00 A, the charge on the capacitor is 40.0 × 10^−6 C. At what time t after the switch is closed is the charge on the capacitor equal to 40.0 x 10^-6 C? When the current has magnitude 3.00 A, at what rate is energy being stored in the capacitor?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Ohm's law Explained; Author: ALL ABOUT ELECTRONICS;https://www.youtube.com/watch?v=PV8CMZZKrB4;License: Standard YouTube License, CC-BY