Cell Membrane Resistance
The capacitance of biological membranes is about 1.0 μF per cm2 of membrane area, so investigators can determine the surface area of a cell membrane by using intracellular electrodes to measure the membrane’s capacitive reactance. An investigator applies a 1.0 μA peak current at 40 kHz to a cell and measures the peak out-of-phase voltage—that is, the component of the voltage due to the capacitive reactance of the cell membrane—to be 0.16 V.
What is the approximate capacitance of the cell membrane?
A. 20 × 10–11 F
B. 10 × 10–11 F
C. 5.0 × 10–11 F
D. 2.5 × 10–11 F
Want to see the full answer?
Check out a sample textbook solutionChapter 26 Solutions
Student Workbook for College Physics: A Strategic Approach Volume 1 (Chs 1-16)
Additional Science Textbook Solutions
An Introduction to Thermal Physics
The Cosmic Perspective
College Physics
Essential University Physics: Volume 2 (3rd Edition)
Essential University Physics (3rd Edition)
- Unreasonable Results In a recording of voltages due to brain activity (an EEG), a 10.0 mV signal with a 0.500 Hz frequency is applied to a capacitor, producing a current of 100 mA. Resistance is negligible. (a) What is the capacitance? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?arrow_forwardThe capacitor in Figure 23.55(a) is designed to filter low—frequency signals, impeding their transmission between circuits. (a) What capacitance is needed to produce a 100 k reactance at a frequency of 120 Hz? (b) What would its reactance be at 1.00 MHz? (c) Discuss the implications of your answers to (a) and (b).arrow_forwardA battery has an emf and internal resistance r. A variable load resistor R is connected across the terminals of the battery. (a) Determine the value of R such that the potential difference across the terminals is a maximum. (b) Determine the value of R so that the current in the circuit is a maximum. (c) Determine the value of R so that the power delivered to the load resistor is a maximum. Choosing the load resistance for maximum power transfer is a case of what is called impedance matching in general. Impedance matching is important in shifting gears on a bicycle, in connecting a loudspeaker to an audio amplifier, in connecting a battery charger to a bank of solar photoelectric cells, and in many other applications.arrow_forward
- Figure P27.48 shows a circuit model for the transmission of an electrical signal such as cable TV to a large number of subscribers. Each subscriber connects a load resistance RL between the transmission line and the ground. The ground is assumed to be at zero potential and able to carry any current between any ground connections with negligible resistance. The resistance of the transmission line between the connection points of different subscribers is modeled as the constant resistance RT. Show that the equivalent resistance across the signal source is Req=12[(4RTRL+RT2)1/2+RT] Suggestion: Because the number of subscribers is large, the equivalent resistance would not change noticeably if the first subscriber canceled the service. Consequently, the equivalent resistance of the section of the circuit to the right of the first load resistor is nearly equal to Req. Figure P27.48arrow_forward(a) What is the resistance of a light bulb that uses an average power of 75.0 W when connected to a 60.0-Hz power source having a maximum voltage of 170. V? (b) What is the resistance of a 100.-W lightbulb?arrow_forwardAn electronic apparatus may have large capacitors at high voltage in the power supply section, presenting a shock hazard even when the apparatus is switched off. A “bleeder resistor" is therefore placed across such a capacitor, as shown schematically in Figure 21.50, to bleed the charge from it after the apparatus is off. Why must the bleeder resistance be much greater than the effective resistance of the rest of the circuit? How does this affect the time constant for discharging the capacitor?arrow_forward
- Figure P32.4 shows three lightbulbs connected to a 120-V AC (rms) household supply voltage. Bulbs 1 and 2 have a power rating of 150 W, and bulb 3 has a 100-W rating. Find (a) the rms current in each bulb and (b) the resistance of each bulb. (c) What is the total resistance of the combination of the three lightbulbs? Figure P32.4arrow_forwardThe capacitance of biological membranes is about 1.0 μF per cm2 of membrane area, so investigators can determine the surface area of a cell membrane by using intracellular electrodes to measure the membrane's capacitive reactance. An investigator applies a 1.0 μA peak current at 40 kHz to a cell and measures the peak out-of-phase voltage--that is, the component of the voltage due to the capacitive reactance of the cell membrane--to be 0.16 V. What is the approximate capacitance of the cell membrane? A. 20×10−11F B. 10×10−11F C. 2.5×10−11F D. 5.0×10−11Farrow_forwardImpedance plethysmography is a technique that can be used to detect thrombosis—the presence of clots in a blood vessel—by measuring the electrical resistance of a limb, such as the calf of the leg. In a typical clinical setting, a current of 200 mA is passed through the leg from the upper thigh to the foot. The voltage is measured at two points along the calf separated by 13 cm.a. If the voltage measured is 17 mV, what is the resistance of the calf between the electrodes?b. If the average calf diameter between the electrodes is 12 cm, what is the average resistivity of this part of the leg?arrow_forward
- Q.1 When a parallel plate capacitor was connected to a 80Hz AC supply, it was found to have a reactance of 410 ohms. Calculate the value of the capacitance in microfarad.arrow_forwardThe capacitor in 23.55(a) is designed to filter lowfrequency signals, impeding their transmission between circuits. (a) What capacitance is needed to produce a 100 kΩ reactance at a frequency of 120 Hz? (b) What would its reactance be at 1.00 MHz? (c) Discuss theimplications of your answers to (a) and (b).arrow_forwardIn order to measure the capacitance of a capacitor a physicist connects it to an oscillating source of emf of amplitude 4.0 x 10-3 V and of frequency f = 318.3 s-1. She finds that the maximum instantaneous current in the capacitor is 8.0 x 10-9 A. What is the capacitance? (Hint: You need to find the reactance first.)arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegePhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning