EBK PHYSICS FOR SCIENTISTS AND ENGINEER
9th Edition
ISBN: 8220100654428
Author: Jewett
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Question
Chapter 27, Problem 27.82CP
(a)
To determine
To show: The resistivity is given approximately by the expression
(b)
To determine
To show: The resistivity is given approximately by the expression
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A more general definition of the temperature coefficient of resistivity is α =1ρ|dρdT|where ρ is the resistivity at temperature T.
(a) Assuming α is constant, show that ρ = ρ0eα(T−T0)
where ρ0 is the resistivity at temperature T0.
(b) Using the series expansion ex ≈ 1 + x for x << 1,
show that the resistivity is given approximately by the expression
ρ = ρ0[1 + α(T − T0)] for α(T − T0) ≪ 1
of 20.0°C and satisfies the equation p = Po[1 + a(T - T)], where po is the resistivity of
= 20.0°C. Suppose the coefficients were given the symbol B and were based on a T, of 0°C, so that they satisfied the equation p = Po*[1+ B(T - 0°C)],
The temperature coefficient of resistivity a is based on a reference temperature
the material at To
where
is the resistivity of the material at 0°C. Obtain the value for the coefficient a from this table and then determine the value of the coefficient B for silver.
Po
(°C)-1
Need Help?
Read It
If R=Ro[1+ a(T - To)], find:
(a) the temperature coefficient of resistivity, a, in terms of R, Ro, T, and To.
(b) the temperature coefficient of resistivity for a resistor with resistances of 8.2 at 33°C and 9.35
at 70°C.
Chapter 27 Solutions
EBK PHYSICS FOR SCIENTISTS AND ENGINEER
Ch. 27 - Consider positive and negative charges of equal...Ch. 27 - Prob. 27.2QQCh. 27 - Prob. 27.3QQCh. 27 - When does an incandescent lightbulb carry more...Ch. 27 - For the two lightbulbs shown in Figure 27.13, rank...Ch. 27 - Car batteries are often rated in ampere-hours....Ch. 27 - Prob. 27.2OQCh. 27 - A cylindrical metal wire at room temperature is...Ch. 27 - Prob. 27.4OQCh. 27 - A potential difference of 1.00 V is maintained...
Ch. 27 - Three wires are made of copper having circular...Ch. 27 - A metal wire of resistance R is cut into three...Ch. 27 - A metal wire has a resistance of 10.0 at a...Ch. 27 - The current-versus-voltage behavior of a certain...Ch. 27 - Two conductors made of die same material are...Ch. 27 - Two conducting wires A and B of the same length...Ch. 27 - Two lightbulbs both operate on 120 V. One has a...Ch. 27 - Wire B has twice the length and twice the radius...Ch. 27 - If you were 10 design an electric healer using...Ch. 27 - Prob. 27.2CQCh. 27 - When the potential difference across a certain...Ch. 27 - Over the lime interval after a difference in...Ch. 27 - How does the resistance for copper and for silicon...Ch. 27 - Use the atomic theory of matter to explain why the...Ch. 27 - If charges flow very slowly through a metal, why...Ch. 27 - Newspaper articles often contain statements such...Ch. 27 - Prob. 27.1PCh. 27 - A small sphere that carries a charge q is whirled...Ch. 27 - Prob. 27.3PCh. 27 - In the Bohr model of the hydrogen atom (which will...Ch. 27 - A proton beam in an accelerator carries a current...Ch. 27 - Prob. 27.6PCh. 27 - Prob. 27.7PCh. 27 - Figure P26.6 represents a section of a conductor...Ch. 27 - The quantity of charge q (in coulombs) that has...Ch. 27 - A Van de Graaff generator (see Problem 24)...Ch. 27 - The electron beam emerging from a certain...Ch. 27 - An electric current in a conductor varies with...Ch. 27 - A teapot with a surface area of 700 cm2 is to be...Ch. 27 - A lightbulb has a resistance of 240 when...Ch. 27 - Prob. 27.15PCh. 27 - A 0.900-V potential difference is maintained...Ch. 27 - An electric heater carries a current of 13.5 A...Ch. 27 - Prob. 27.18PCh. 27 - Prob. 27.19PCh. 27 - Prob. 27.20PCh. 27 - A portion of Nichrome wire of radius 2.50 mm is to...Ch. 27 - If the current carried by a conductor is doubled,...Ch. 27 - Prob. 27.23PCh. 27 - Prob. 27.24PCh. 27 - If the magnitude of the drill velocity of free...Ch. 27 - Prob. 27.26PCh. 27 - Prob. 27.27PCh. 27 - While taking photographs in Death Valley on a day...Ch. 27 - Prob. 27.29PCh. 27 - Plethysmographs are devices used for measuring...Ch. 27 - Prob. 27.31PCh. 27 - An engineer needs a resistor with a zero overall...Ch. 27 - An aluminum wire with a diameter of 0.100 mm has a...Ch. 27 - Review. Ail aluminum rod has a resistance of 1.23 ...Ch. 27 - At what temperature will aluminum have a...Ch. 27 - Assume that global lightning on the Earth...Ch. 27 - In a hydroelectric installation, a turbine...Ch. 27 - A Van de Graaff generator (see Fig. 25.23) is...Ch. 27 - A certain waffle iron is rated at 1.00 kW when...Ch. 27 - The potential difference across a resting neuron...Ch. 27 - Suppose your portable DVD player draws a current...Ch. 27 - Review. A well-insulated electric water healer...Ch. 27 - A 100-W lightbulb connected to a 120-V source...Ch. 27 - The cost of energy delivered to residences by...Ch. 27 - Prob. 27.45PCh. 27 - Residential building codes typically require the...Ch. 27 - Assuming the cost of energy from the electric...Ch. 27 - An 11.0-W energy-efficient fluorescent lightbulb...Ch. 27 - A coil of Nichrome wire is 25.0 m long. The wire...Ch. 27 - Review. A rechargeable battery of mass 15.0 g...Ch. 27 - A 500-W heating coil designed to operate from 110...Ch. 27 - Why is the following situation impossible? A...Ch. 27 - A certain toaster has a heating element made of...Ch. 27 - Make an order-of-magnitude estimate of the cost of...Ch. 27 - Review. The healing element of an electric coffee...Ch. 27 - A 120-V motor has mechanical power output of 2.50...Ch. 27 - Prob. 27.57APCh. 27 - Prob. 27.58APCh. 27 - Prob. 27.59APCh. 27 - Lightbulb A is marked 25 W 120 V, and lightbulb B...Ch. 27 - One wire in a high-voltage transmission line...Ch. 27 - An experiment is conducted to measure the...Ch. 27 - A charge Q is placed on a capacitor of capacitance...Ch. 27 - Review. An office worker uses an immersion heater...Ch. 27 - Prob. 27.65APCh. 27 - An all-electric car (not a hybrid) is designed to...Ch. 27 - Prob. 27.67APCh. 27 - Prob. 27.68APCh. 27 - An electric utility company supplies a customers...Ch. 27 - The strain in a wire can be monitored and computed...Ch. 27 - An oceanographer is studying how the ion...Ch. 27 - Why is the following situation impossible? An...Ch. 27 - Prob. 27.73APCh. 27 - A close analogy exists between the flow of energy...Ch. 27 - Review. When a straight wire is warmed, its...Ch. 27 - Prob. 27.76APCh. 27 - Review. A parallel-plate capacitor consists of...Ch. 27 - The dielectric material between the plates of a...Ch. 27 - Prob. 27.79APCh. 27 - Prob. 27.80APCh. 27 - The potential difference across the filament of a...Ch. 27 - Prob. 27.82CPCh. 27 - A spherical shell with inner radius ra and outer...Ch. 27 - Material with uniform resistivity is formed into...Ch. 27 - A material of resistivity is formed into the...
Knowledge Booster
Similar questions
- Resistivity in metals increases with temperature according to the equation: ρ(T) = ρ0[1 + α(T - T0)] where α is the temperature coeficcient of restivity, and ρ0 is the restivity at the reference temperature T0. For a particular wire, the temperature coeficcient of restivity is α = 3.83 X 10-3 °C-1, and the restivity is ρ0 = 7.71 X 10-7 Ωm at the reference temperature T0 = 297°C. Find an expression for the temperature T2, at which the resistance of a particular wire will be twice as high as it is at the reference temperature T0. (Both temperatures are in degrees Celsius) Use this expression to find the temperature in degrees Celsius for T2. If the wire has a length of 1.00m and it has a circular cross section with a radius of 1.00cm, what is the resistance in ohms, at a temperature which is twice the reference temperature, T = 2T0 ?arrow_forwardThe current I is measured through a sample of an ohmic material as a voltage V is applied. (a) What is the current when the voltage is doubled to 2V (assume the change in temperature of the material is negligible)? (b) What is the voltage applied is the current measured is 0.2I (assume the change in temperature of the material is negligible)? What will happen to the current if the material if the voltage remains constant, but the temperature of the material increases significantly?arrow_forwardConsider the following scenario: An engineering student measures the resistivity of a particular cylindrical wire for different lengths L by tapping at points the wire from 0.1 m to 1 m in steps of 0.1 m. The radius of the wire is 0.2 mm. The experiment is carried out under following circumstances: a) The best line has been drawn through the points given below and determine the resistivity of the wire from the slope of the plot between blue marked points. b) Based on the value of resistivity you calculated, what is the material wire resistor made of? Make sure everything is in ohms and meters, otherwise your units will not work out correctly in the end!arrow_forward
- Show that, according to the free-electron model of electrical conduction in metals and classical physics, the resistivity of metals should be proportional to where T is the temperature in kelvins.arrow_forwardConsider a resistor of resistivity 4.84 x 10-8 n.m. If an electric field of 18 V/m is applied across the resistor and the electron volume concetration in the conductor is 4.39 x 1028 per m3, determine the drift velocity, in mm/s, of the free electron constituting the current. In the dedicated field, enter only the value being asked in the problem. Express answers accurate to four decimal places for the final answer. Do not enter the unit of measurement as it is already indicated in the problem. This specific item DOES NOT require solutions.arrow_forwardYou plotted a graph of current vs. voltage and found the slope of the best fit line is m± Am = 4.69 ± 1.79 Amps/Volt. The resistance can be calculated from the slope by knowing: R = 1 m The fractional uncertainty in the slope is equivalent to the fractional uncertainty in the resistance: AR R = Am m Calculate the uncertainty in the resistance, AR in units of (ohms), then enter the raw value (no units) into the box below. Round to two decimal places. AR=arrow_forward
- A platinum resistance thermometer (PRT) is a transducer which measures temperature 0 by means of consequent change of electrical resistance RT between its two terminals. Such a PRT has the following quadratic characteristic: RT=Ro [1+A0+BO^2] The PRT is calibrated so that its resistance is Ro = 100 Q at a reference temperature of 0 = 0°C. The coefficients have the following values: A = +4.0 x 10-3 °C-1 B = -5.0 x 10-6 oc-2 Determine sensitivity of this transducer at temperatures of +50 °C. Select one: O a. 0.45 Q/°C Ob. -0.45 Q/°C -0.35 Ω/ΟC d. 0.4 0/°C O e. 0.35 Q/°C O f. -0.4 0/PCarrow_forwardCheap resistors are fabricated by depositing a thinlayer of carbon onto a nonconducting cylindrical substrate. If such a cylinder has radius a and length d, determine the thickness of the film required for a resistance R ifa = 1 mm R = 33 kσ = 1ρ = 2.9 MS/md = 9 mmNeglect the end surfaces of the cylinder and assumethat the thickness is much smaller than the radius.arrow_forwardThe space between two conducting concentric spheres ofradii a and b (a < b) is filled up with homogeneous poorly conductingmedium. The capacitance of such a system equals C. Find the resistivity of the medium if the potential difference between the spheres,when they are disconnected from an external voltage, decreasesn-fold during the time interval Δt.arrow_forward
- The length and diameter of an aluminum wire is twice the length and diameter of a copper wire, respectively. Find the ratio of the resistances of the two wires.arrow_forwardThe current–voltage characteristic curve for a semiconductor diode as a function of temperature T is given by I = I0(eeΔV/kBT - 1)Here the first symbol e represents Euler’s number, the base of natural logarithms. The second e is the magnitude of the electron charge, the kB stands for Boltzmann’s constant, and T is the absolute temperature. (a) Set up a spreadsheet to calculate I and R = ΔV/I for ΔV = 0.400 V to 0.600 Vin increments of 0.005 V. Assume I0 = 1.00 nA. (b) Plot R versus ΔV for T = 280 K, 300 K, and 320 K.arrow_forwardIn the classic model for electrical conduction, electron mobility u in a metal wire is defined as where v, is the drift velocity of the electrons and E is the electric field in the metal. This parameter is a measure of how freely electrons can travel through a metal when an electric field is applied, such as when the ends of a metal wire are connected to a potential difference. (a) Show that where a is the conductivity of the metal, n is the number density of the charge carriers, and q is the charge on each carrier. (Submit a file with a maximum size of 1 MB.) Choose File no file selected This answer has not been graded yet. (b) B = AVH is often written as AVH - R IB where R, is the Hall coefficient of the metal. Show that the following is true. (Submit a file with a maximum size of 1 MB.) Hyo -n (Choose File no file selected This answer has not been graded yet (c) The table below shows some measured values of Hall coefficients for some elemental materials. What is an average number…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning