Principles of Instrumental Analysis, 6th Edition
6th Edition
ISBN: 9788131525579
Author: Douglas A. Skoog, F. James Holler, Stanley R. Crouch
Publisher: Cenage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 29, Problem 29.10QAP
Interpretation Introduction
Interpretation:
The recovery process of analytes after an SFE is to be discussed.
Concept introduction:
When there is a use of supercritical fluid as an extracting solvent, the extraction process is termed as the supercritical fluid extraction method.
This type of extraction method is applied for separating essential oils, flavors, fat and other ingredients from the mixtures.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
analyte
concentration(C)(mg/ml)
injection volume (ul)
elution time (time)
peak DAD signal(mAU)
caffeine
1
1
4.67
302.85
aspartame
5
1
7.53
15.83
benzoic acid
1
1
8.14
89.98
saccharin
1
1
1.91
84.86
mixture(add everything above with 1:1:1:1 ratio)
1
4.47
69.58
How to get the concentration of the mixture in this case?
How analytes are recovered from SFC and SFE
How are analytes usually recovered after SFC or SFE?
Chapter 29 Solutions
Principles of Instrumental Analysis, 6th Edition
Knowledge Booster
Similar questions
- What can labs do to reduce error in GC- ms??arrow_forwardSuppose that a lead determination has a standard deviation of 3 mg. If the sample has a mean value of 60 mg, the CV is 5%. For a sample containing only 15 mg, the CV isarrow_forward▪ In a blood alcohol analysis by GC-FID, methanol elutes at 1 min, ethanol at 2 min, IPA at 3 min, and IS at 4 min. In the patient sample, the analyte elutes t 2 min and the IS at 8 min. What is the relative retention time and the analyte in the patient? A) methanol B) Ethanol chu C) IPAarrow_forward
- ■ True or False: in a TOF analyzer, a fragment of low mass reaches the detector first ▪ In GCMS when we know what analytes we are measuring we use not know what analytes are in the sample we use than scan. ▪ A) Scan; SIM ■ B)SIM; scan • C) SIM; SIM mode. When we do mode. SIM allows greater sensitivityarrow_forwardIf Jotaro Kujo measured the amount of current that passes through a sample to measure the amount of analyte in the sample, what kind of method did he use? Volumetric method Spectroscopic method Gravimetric method Electroanalytical methodarrow_forwardWhy chromatography is an important tool for analysis of organic compounds?arrow_forward
- 1) Titrant 5 mg H2O/ mL Resolution 2.5 µg H2O/step Detection limit is 125 µg H2O for a 5 g sample (= 25 ppm) 2) Titrant 2 mg H2O/ mL Resolution 1 µg H2O/step Detection limit is 50 µg H2O for a 5 g sample (= 10 ppm) You have a 10 g sample which is expected to contain 200 µg H2O. True or false? 1. Titrant 5mg/mL is the preferred system over 2. Titrant 2mg/mL for this sample. True Falsearrow_forwardwhat is the concentration of the unknown sample using serial diluitions: 0.05M 1.7472nm, 0.025M 0.8569nm, 0.0125M 0.4167nm, 0.00625M 0.1958nm the epsilon value is 0.0101 and l is 1 cmarrow_forwardA sample of explosives residue is dissolved in an appropriate solvent and is injected into HPLC. The column contains a non- polar stationary phase. The sample revealed three chemical compounds that are commonly present in homemade explosives. ТAТP DADP HMTD 1 2 3 4 5 6 7 8 Retention time (minutes) a) determine the retention time of TATP. b) which one elute first :DADP,TATP or HMTD? c) State and explain which compound is most polar. d) If you are investigating this terrorist attacks, state one way in which the information in the chromatogram would be useful.arrow_forward
- What is the percent error of the Ksp of Ca(OH)2 if the experimental value is 9.1 x 10^-5 and the accepted value is 5.5 x 10^-6?arrow_forwardWhat are the differences between systematic and random errors and how do they effect accuracy and precision? In what circumstances would you use standard addition (versus a normal calibration curve) to determine the amount of an analyte in a sample? A urine sample, containing analyte Z is analysed by the standard addition method where 5 mL of the original sample was mixed with increasing amounts of a Z standard and each solution diluted to a volume of 50 mL prior to analysis. A plot of the final concentration of the standard in each of the 50 mL samples (x axis) versus The measured signal from the analysis of each 50 mL sample (on y axis) produced a straight line with the general equation: y = 44.72x + 4.06 what was the final concentration of Z in the 50 mL standard addition sample? what was the initial concentration of Z in the original urine sample?arrow_forwardData Collection Kinetic Data Collection Time, t (s) Volume of added base (mL) First addition 40 0.50 Second addition 101 1.00 Third addition 160 1.52 Fourth addition 224 1.99 Fifth addition 278 2.49 Sixth addition 334 3.01 Seventh additlon 389 3.48 Calculations Concentration of NaOH stock solution: 0.01 M Concentration of t-BuCl stock solution: 0.2 M Volume of t-BuCl solution: 10 mL stock stock solution added to 25 mL acetone Table view List view Kinetic Data Volume of Moles of Amount of t-Bucl (mol) [-Buc] In[-BuC Time, t (s) added base added base (mL) (mol) First addition 40 0.50 Second additlon 101 1.00 Third addition 160 1.52 Fourth addition 224 1.99 Flfth additlon 278 2.49 Sixth additlon 334 3.01 Seventh addition 389 3.48 Use the data in the table above to plot In[t-BuC]]; vs time (s). Include labelled axis, a title, and a linear trendline. Upload your plot here.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
