Manufacturing Engineering And Technology -- Access Card
7th Edition
ISBN: 9780133131109
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 35, Problem 13RQ
What is the difference between bilateral and unilateral tolerance?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Explain what is meant by the tolerance percent defective ?
Limits and tolerances
a) Name two groups of standards in addition to national, industry-wide standards and where they are valid.
b) Which three options exist for defining dimensional tolerances in a technical drawing?
Chapter 35 Solutions
Manufacturing Engineering And Technology -- Access Card
Ch. 35 - What is metrology?Ch. 35 - Explain how a meter is defined and measured.Ch. 35 - Explain what is meant by standards for...Ch. 35 - What is the basic difference between...Ch. 35 - What is meant by comparative length measurement?Ch. 35 - Explain how flatness is measured. What is an...Ch. 35 - Describe the principle of an optical comparator.Ch. 35 - Why have coordinate measuring machines...Ch. 35 - What is the difference between a plug gage and...Ch. 35 - What are dimensional tolerances? Why is their...
Ch. 35 - Prob. 11RQCh. 35 - Explain the difference between tolerance and...Ch. 35 - What is the difference between bilateral and...Ch. 35 - How is straightness measured?Ch. 35 - When is a clearance fit desirable? An interference...Ch. 35 - What factors contribute to deviations in the...Ch. 35 - Why are the words accuracy and precision...Ch. 35 - Prob. 18QLPCh. 35 - Prob. 19QLPCh. 35 - Prob. 20QLPCh. 35 - Dimensional tolerances for nonmetallic parts...Ch. 35 - Prob. 22QLPCh. 35 - Review Fig. 35.20, and comment on the range...Ch. 35 - In the game of darts, is it better to be accurate...Ch. 35 - What are the advantages and limitations of GO...Ch. 35 - Comment on your observations regarding Fig. 35.19.Ch. 35 - What are gage blocks? Explain three methods...Ch. 35 - Why is it important to control temperature during...Ch. 35 - Describe the characteristics of electronic gages.Ch. 35 - What method would you use to measure the...Ch. 35 - Prob. 31QLPCh. 35 - Review Fig. 35.21 and give reasons that there is a...Ch. 35 - Assume that a steel rule expands by 0.07% due to...Ch. 35 - If the same steel rule as in Problem 35.33 is used...Ch. 35 - A shaft must meet a design requirement of being at...Ch. 35 - Describe your thoughts on the merits and...Ch. 35 - Take an ordinary vernier micrometer (see Fig....Ch. 35 - Obtain a digital micrometer and a steel ball of,...Ch. 35 - Prob. 41SDPCh. 35 - Prob. 42SDPCh. 35 - Inspect various parts and components in...Ch. 35 - Prob. 45SDPCh. 35 - Prob. 46SDPCh. 35 - Prob. 47SDPCh. 35 - Conduct an Internet search, and make a list of...Ch. 35 - Prob. 49SDP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is a part's tolerance?arrow_forwardWhich type of feature doesn't belong to form tolerances? a)The profile of a surface b)Circularity c)Cilindricity d)Flatnessarrow_forwardTo which of the following geometric tolerance families does perpendicularly belong? Form Tolerance. Location tolerance. Profile tolerance. Orientation tolerancearrow_forward
- What circumstances necessitate recalibration and replacement of the measuring device?arrow_forwardRound off to 3 significant figures, and the tolerance is ±1 in the 3rd significant digit. Thank you.arrow_forwardKindly provide a full solution, an answer in 3 significant figures, and tolerance is ± 1 in the 3rd significant digit. Thank you.arrow_forward
- A GO/NO-GO snap gage is required to inspect the diameter of a shaft that is 1.000 ± 0.020. A wear allowance of 2% of the entire tolerance band is applied to the GO side. Determine (a) the nominal sizes of (a) the GO gage and (b) the NO-GO gagearrow_forwardNote: The number of significant digits is set to 3. The tolerance is +/- 1 in the 3rd significant digit Subject: statics of rigid bodies// mechanical engineeringarrow_forwardQuestion 1(a)Given the measured value is 20.04mm and the true value of the measured dimensionis +-(plus minus) 20.02. Calculate the percentage of errors on this dimension.(b)Some errors in the measurement can be avoided. List 3 of the avoidable errors inmeasuring of component.(c)Named the 4 classifications of the Tolerance and briefly explain each of it.arrow_forward
- Having trouble with review activity 10-2 (pg 209) regarding calculating tolerance????arrow_forwardFor the following statements, answer True or False and explain the answer briefly. The tolerance of standard mass used must be smaller than the uncertainty of analytical balance to be calibrated.arrow_forwardWhat other geometric tolerance is automatically controlled when parallelism is applied to a surface? Position. Symmetry. Flatness. Profile.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY