Manufacturing Engineering And Technology
7th Edition
ISBN: 9789810694067
Author: Stephen R. Schmid (author) Serope Kalpakjian (author)
Publisher: Pearson Education Orphans
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 35, Problem 17QLP
Why are the words “accuracy” and “precision” often incorrectly interchanged?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
If you were manufacturing a component with a minimum thickness of 1mm and a
tolerance of 0.1mm (or better) which method may be appropriate to achieve this?
Which is a more precise (or exact) measuring tool, the top-loading balance or the graduated cylinder?
What part provides the most manufacturing tolerance and is easiest to work with, part 1 or part 2? Explain why.
Chapter 35 Solutions
Manufacturing Engineering And Technology
Ch. 35 - What is metrology?Ch. 35 - Explain how a meter is defined and measured.Ch. 35 - Explain what is meant by standards for...Ch. 35 - What is the basic difference between...Ch. 35 - What is meant by comparative length measurement?Ch. 35 - Explain how flatness is measured. What is an...Ch. 35 - Describe the principle of an optical comparator.Ch. 35 - Why have coordinate measuring machines...Ch. 35 - What is the difference between a plug gage and...Ch. 35 - What are dimensional tolerances? Why is their...
Ch. 35 - Prob. 11RQCh. 35 - Explain the difference between tolerance and...Ch. 35 - What is the difference between bilateral and...Ch. 35 - How is straightness measured?Ch. 35 - When is a clearance fit desirable? An interference...Ch. 35 - What factors contribute to deviations in the...Ch. 35 - Why are the words accuracy and precision...Ch. 35 - Prob. 18QLPCh. 35 - Prob. 19QLPCh. 35 - Prob. 20QLPCh. 35 - Dimensional tolerances for nonmetallic parts...Ch. 35 - Prob. 22QLPCh. 35 - Review Fig. 35.20, and comment on the range...Ch. 35 - In the game of darts, is it better to be accurate...Ch. 35 - What are the advantages and limitations of GO...Ch. 35 - Comment on your observations regarding Fig. 35.19.Ch. 35 - What are gage blocks? Explain three methods...Ch. 35 - Why is it important to control temperature during...Ch. 35 - Describe the characteristics of electronic gages.Ch. 35 - What method would you use to measure the...Ch. 35 - Prob. 31QLPCh. 35 - Review Fig. 35.21 and give reasons that there is a...Ch. 35 - Assume that a steel rule expands by 0.07% due to...Ch. 35 - If the same steel rule as in Problem 35.33 is used...Ch. 35 - A shaft must meet a design requirement of being at...Ch. 35 - Describe your thoughts on the merits and...Ch. 35 - Take an ordinary vernier micrometer (see Fig....Ch. 35 - Obtain a digital micrometer and a steel ball of,...Ch. 35 - Prob. 41SDPCh. 35 - Prob. 42SDPCh. 35 - Inspect various parts and components in...Ch. 35 - Prob. 45SDPCh. 35 - Prob. 46SDPCh. 35 - Prob. 47SDPCh. 35 - Conduct an Internet search, and make a list of...Ch. 35 - Prob. 49SDP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which order arranges the following manufacturing processes from the least precise to the most precise tolerance limits?POSSIBLE ANSWERS1 . Turning, grinding, casting2 . Casting, turning, grinding3 . Casting. grinding, turning4 . Turning, casting, grindingarrow_forwardA machine that produces ball bearings has initially been set so that the true averagediameter of the bearings it produces is .500 in. A bearing is acceptable if itsdiameter is within .004 in. of this target value. Suppose, however, that the settinghas changed during the course of production, so that the bearings have normallydistributed diameters with mean value .499 in. and standard deviation .002 in.What percentage of the bearings produced will not be acceptable?Step by Step Full procedure required.arrow_forwardName some mechanical testing methods?arrow_forward
- Why might a 50 division vernier caliper not be more advantageous, in terms of measurement accuracy, than a 10 division vernier caliper?arrow_forwardOrthogonal cutting, in a machining process,The attacking team sawdust (α) is 10 ̊. operationchip (t0) 0.5 mm and machining beforeAfter the chip coating (tc) is 1,125 mm.Accordingly, in machining;a) Slip plane (ϕ),b) Shear strain (γ) calculatorarrow_forwardWhat is Direct Measurement? - Give 3 Instruments for every basic process variables, its description operation and preffered applicationarrow_forward
- What is the testing plan for universal testing machines? How are the tests to be done is planned in the beginning to the end?arrow_forwarda) What is vibration and vibration analysis of a machine? List the methods used to eliminate vibration from a machine or a structure.arrow_forwardWhat are the significance of tolerance and allowance in production process? Diagram?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY