Manufacturing Engineering And Technology
7th Edition
ISBN: 9789810694067
Author: Stephen R. Schmid (author) Serope Kalpakjian (author)
Publisher: Pearson Education Orphans
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 4, Problem 10RQ
Explain what is meant by “severity of quenching.”
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is quenching ? Why should quenched still be tempered ? Discuss .
What is quenching? Why should quenched steel be tempered?
Explain the reason for the quenching cracking that may occur when hardening some parts. Describe the alternative methods applied to prevent this situation by showing them on a single figure.
Chapter 4 Solutions
Manufacturing Engineering And Technology
Ch. 4 - Describe the difference between a solute and a...Ch. 4 - What is a solid solution?Ch. 4 - Prob. 3RQCh. 4 - Describe the difference between a single-phase and...Ch. 4 - What is an induction heater? What kind of part...Ch. 4 - Describe the major features of a phase diagram.Ch. 4 - What do the terms equilibrium and constitutional,...Ch. 4 - Prob. 8RQCh. 4 - What is tempering? Why is it performed?Ch. 4 - Explain what is meant by severity of quenching.
Ch. 4 - What are precipitates? Why are they significant in...Ch. 4 - Prob. 12RQCh. 4 - Prob. 13RQCh. 4 - Prob. 14RQCh. 4 - Prob. 15RQCh. 4 - You may have seen some technical literature on...Ch. 4 - Prob. 17QLPCh. 4 - What is the difference between hardness and...Ch. 4 - Prob. 19QLPCh. 4 - Prob. 20QLPCh. 4 - Prob. 21QLPCh. 4 - Describe the characteristics of (a) an alloy, (b)...Ch. 4 - Explain why carbon, among all elements, is so...Ch. 4 - Prob. 24QLPCh. 4 - In Section 4.8.2, several fluids are listed in...Ch. 4 - Why is it important to know the characteristics of...Ch. 4 - Explain why, in the abscissa of Fig. 4.16c, the...Ch. 4 - Prob. 28QLPCh. 4 - Prob. 29QLPCh. 4 - Prob. 30QLPCh. 4 - Design a heat-treating cycle for carbon steel,...Ch. 4 - Using Fig. 4.4, estimate the following quantities...Ch. 4 - Prob. 33QTPCh. 4 - Prob. 34QTPCh. 4 - Prob. 35SDPCh. 4 - Figure 4.18b shows hardness distributions in...Ch. 4 - Throughout this chapter, you have seen specific...Ch. 4 - Refer to Fig. 4.24, and think of a variety of...Ch. 4 - Inspect various parts in your car or home, and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe the process conditions necessary to create a)a cored microstructure and b) a non- cored microstructure.?arrow_forwardBriefly explain the heat treatment steps of a tool steel by use of proper drawings and explainwhy multiple tempering is applied during heat treatment?arrow_forwardGive information about tempering heat treatment temperature stages, microstructures formed and effects on mechanical properties.arrow_forward
- 1.Mention four quenchants and describe how each of them affect the strength of the material being quenched arranging them in a decending ordrer. 2. Draw a typical time temperature transformation diagram showing how a material is cooled under critical cooiling rate. 3. explain non equilibrium coolingarrow_forwardUse the TTT diagram for O1 Tool steel provided above to estimate the amounts ofpearlite and martensite formed in the quenched heat-treated samples.arrow_forwardPlease explain and solve the following question and do any skecthes as needed for me to understand. explain the distinguishing features of eutectoid and martensitic transformations in steel have? Compare and contrast them in briefarrow_forward
- Explain the concept and procedures involved in a case hardening process of a low carbon steel and provide an example of the application of this technique to solving engineering problemsarrow_forwardEstimate the quench rate (in °C/s) needed to avoid pearlite formation in 1.13 wt % C steel. Note that the quench rate is ΔT/tarrow_forwardWhy is the formation of martensite a problem when welding on high carbon steels?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Chemical and Phase Equilibrium; Author: LearnChemE;https://www.youtube.com/watch?v=SWhZkU7e8yw;License: Standard Youtube License