MACROSCALE+MICRO.ORG...-OWLV2 ACCESS
7th Edition
ISBN: 9781305884175
Author: Williamson
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Question
Chapter 4, Problem 11Q
Interpretation Introduction
Interpretation:
The reason to avoid the use of beaker for recrystallization should be determined.
Concept introduction:
Recrystallization is a technique that is used to purify the impure compounds. It is based on the principle that the solubility of substances increases with the increase in temperature.
Following are some of the types of recrystallization:
- Single-solvent recrystallization
- Multi-solvent recrystallization
- Hot filtration-recrystallization
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Explain different ways to induce recrystallization.
Make a Flow chart diagram of the PROCESS OF RECRYSTALLIZATION
Describe the steps involved in recrystallization.
Chapter 4 Solutions
MACROSCALE+MICRO.ORG...-OWLV2 ACCESS
Knowledge Booster
Similar questions
- Draw an outline of the recrystallization process- Assume all types of Impurities(Soluble, Insoluble and colored) are present.arrow_forwardWhy is it important to cool slowly during recrystallizationarrow_forwardBriefly explain why crystals form as the solvent cools during recrystallization.arrow_forward
- Ratio of peppermint water to make 60ml? What is the stepwise procedure for preparation of peppermint water?arrow_forwardIn an experiment, is a 100% yield possible in recrystallization? Please explain.arrow_forward6. What are the factors affect that decrease the percent yield during a recrystallization?arrow_forward
- 2. When performing the recrystallization of an impure solid, why is it advised to use the minimal amount of solvent possible? Group of answer choices To minimize the amount of pure solid lost due to its solubility. To minimize the cost of the recrystallization. To reduce the time needed to filter the pure solid from the solvent after recrystallization. To minimize the amount of hazardous materials used.arrow_forwardIn a test tube, dissolve 10 drops of methanol in 3 ml. of water. Oxidize a copper wire spiral by passing it through a Bunsen burner. Plunge the red-hot wire into the alcohol solution several times, cooling the solution under the tap (faucet) so as not to evaporate too much of it. Next, add 1 drop of 0.5% resorcinol solution. Measure 2 ml. of concentrated sulfuric acid (CAUTION!) and pour this carefully down the sides of the test tube containing the mixture. Note the color of the zone intermediate between the acid and the solution. RESULT:arrow_forwardWeigh out 5g of table salt. Dissolve it in 50mL of distilled water in a container using a stirrer and label appropriately. Calculate the concentration in terms of percent mass per volume.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Chemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage LearningChemistry: Matter and ChangeChemistryISBN:9780078746376Author:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl WistromPublisher:Glencoe/McGraw-Hill School Pub Co
Chemistry: The Molecular Science
Chemistry
ISBN:9781285199047
Author:John W. Moore, Conrad L. Stanitski
Publisher:Cengage Learning
Chemistry: Matter and Change
Chemistry
ISBN:9780078746376
Author:Dinah Zike, Laurel Dingrando, Nicholas Hainen, Cheryl Wistrom
Publisher:Glencoe/McGraw-Hill School Pub Co