Concept explainers
Casting molten metal is important in many industrial processes. Centrifugal casting is used for manufacturing pipes, bearings, and many other structures. A variety of sophisticated techniques have been invented, but the basic idea is as illustrated in Figure P4.35. A cylindrical enclosure is rotated rapidly and steadily about a horizontal axis. Molten metal is poured into the rotating cylinder and then cooled, forming the finished product. Turning the cylinder at a high rotation rate forces the solidifying metal strongly to the outside. Any bubbles are displaced toward the axis, so unwanted voids will not be present in the casting. Sometimes it is desirable to form a composite casting, such as for a bearing. Here a strong steel outer surface is poured and then inside it a lining of special low-friction metal. In some applications, a very strong metal is given a coating of corrosion-resistant metal. Centrifugal casting results in strong bonding between the layers.
Suppose a copper sleeve of inner radius 2.10 cm and outer radius 2.20 cm is to be cast. To eliminate bubbles and give high structural integrity, the centripetal acceleration of each bit of metal should be at least 100g. What rate of rotation is required? State the answer in revolutions per minute.
Trending nowThis is a popular solution!
Chapter 4 Solutions
EBK PHYSICS FOR SCIENTISTS AND ENGINEER
- You're out in space, on a rotating wheel-shaped space station of radius 1426 m. You feel planted firmly on the floor due to artificial gravity. The gravity you experience is Earth-normal, that is, g = 9.81 m/s^2. How fast is the space station rotating in order to produce this much artificial gravity? Express your answer in revolutions per minute (rpm). 0.083 rpm 118.3 rpm 0.554 rpm 0.792 rpmarrow_forwardAn object moving in a circular trajectory experiences both centripetal and tangential accelerations. Can the two accelerations ever cancel each other out? a No. b You're kidding, right? c Yes. d Only if the plane of the trajectory makes an angle with the vertical.arrow_forwardA motorist travels along a vertical circle with a diameter of 10.0 m. After one successful revolution, he notices that his speed at the bottom of the pathway is 6.50 m/s. The mass of the motorists is 70.0 kg. What is the radial acceleration of the motorist at the bottom of the pathway?arrow_forward
- Modern wind turbines are larger than they appear, and despite their apparently lazy motion, the speed of the blades tips can be quite high—many times higher than the wind speed. A typical modern turbine has blades 56 m long that spin at 13 rpm. At the tip of a blade, what are (a) the speed and (b) the centripetal acceleration?arrow_forwardYou are working in a biology lab and learning to use a new ultracentrifuge for blood tests. The specifications for the centrifuge say that a red blood cell rotating in the ultracentrifuge moves at 470 m/s and has a radial acceleration of 150,000 g's (150,000 times the freefall acceleration of 9.8 m/s2). The radius of the centrifuge is 0.15 m. You wonder if this claim is correct. Support your answer with a calculation.arrow_forwardOn the International Space Station an object with mass m = 440 g is attached to a massless string of length L = 0.61 m. The string can handle a tension of T = 5.8 N before breaking. The object undergoes uniform circular motion, being spun around by the string horizontally.What is the maximum speed v the mass can have before the string breaks? Give your answer in units of m/s.arrow_forward
- A light, rigid rod is 50.2 cm long. Its top end is pivoted on a frictionless horizontal axle. The rod hangs straight down at rest with a small, massive ball attached to its bottom end. You strike the ball, suddenly giving it a horizontal velocity so that it swings around in a full circle. What minimum speed at the bottom is required to make the ball go over the top of the circle? m/sarrow_forwardA green car starts off at the finish line at 0 m/s (initial velocity). The green race car does a complete rotation around the track. The track is 800 meters in length. When the race car reaches the finish line, it is driving at 30m/s in the west direction (final velocity). A second car, which is red, now pulls up to the finish line. The red car starts off at rest (initial velocity) and then speeds around the track at a velocity of 40 m/s west (final velocity), which flashed on the screen after the first lap. This took 20 seconds for the car to complete a full rotation.Compare the displacement of the green car to the displacement of the red car for 1 lap around the track.arrow_forwardQuestion 4. A single bead can slide without friction on a vertical hoop of radius r. The hoop rotates about its vertical axis and makes one complete revolution in T seconds. The position of the bead is described by the angle 0. At what 0 > 0 can the bead stay stationary while the hoop rotates? rarrow_forward
- Hi, today I had my engineering mechanics 1 test which I completely screwed up. I was quite confident in the uniform circular motion, but I had this problem in my exam which completely confused me. When I read "upward vertical acceleration" my head just start to spin as I couldn't understand what force could cause an upward acceleration. Could you help me with this problem? I bet it is easier than it looks, but still, I am confused about what is asking me and most importantly about the input it is giving me. I don't have my exam paper with me, but on my body diagram, I knew that on the aeroplane were exerted the Force of Contact Fn1 and the Force m1g in the y opposite direction. On the pilot was acting the Force of Contact with the seat of the aeroplane Fn2 and the m2g in the y opposite direction. Here is the problem: During an air show an aircraft comes out of a dive at the bottom of a circular arc at a horizontal speed of 97m/s. In the cockpit the aircraft pilot of mass 58kg…arrow_forwardI got 200 meters on this one.arrow_forwardA Ferris wheel has a radius of 30 m and its centre is 32 m above the ground. It rotates once every 48 s. Ethan gets on the Feris wheel at the lowest point and then the wheel starts to rotate. The amount of time it takes Ethan to reach 38 m above the ground for the first time, to the nearest tenth of a second, is S. Your answerarrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning