Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 4, Problem 4.8PP
A tank containing liquid ammonia at
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A vertical bulkhead is 2 metres wide and 3.7 metres high. It has fresh water on one side to a depth of 3 metres and seawater on the other side to a depth of 3.5 metres. Calculate the resultant force on the door.
A vertical bulk head is 2 meters wide and 3.7 meters high. It has fresh water on one side to a depth of 3 meters and sea water on the other side to a depth of 3.5 meters. Calculate the resultant force on the door.
SOLVE THE FF, SHOW YOUR COMPLETE SOLUTION (ANSWERS MUST BE IN 3 DECIMAL PLACES).
The scow is 50 ft long, 30 ft wide and 8 ft deep. It has a draft of 5ft, when floating in an upright position. The center of gravity of the scow is on the axis of the symmetry 1ft above the water surface. Find:
(a) The initial metacentric height (at initial position)
(b) The metacentric height in tilted position when the angle of tilt is 10.
(c) The distance between weight and the buoyancy in tilted position.
(d) The moment created.
(e) Classify the kind of moment.
(f) The shifted distance of buoyancy.
Chapter 4 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 4 - figure 4.2 shows a vacuum tank with a flat...Ch. 4 - The flat left end of the tank shown in Fig. 4.21...Ch. 4 - An exhaust system for a room creates a partial...Ch. 4 - A piece of 14 -in Schedule 40 pipe is used as a...Ch. 4 - A pressure relief valve is designed so that the...Ch. 4 - A gas-powered cannon shoots projectiles by...Ch. 4 - The egress hatch of a manned spacecraft is...Ch. 4 - A tank containing liquid ammonia at 77F has a flat...Ch. 4 - The bottom of a laboratory vat has a hole in it to...Ch. 4 - A simple shower for remote locations is designed...
Ch. 4 - Calculate the total force on the bottom of the...Ch. 4 - If the length of the tank in Fig. 4.24 is 1.2m,...Ch. 4 - An observation port in a small submarine is...Ch. 4 - A rectangular gate is installed in a vertical wall...Ch. 4 - '4.15 A vat has a sloped side, as shown in Fig....Ch. 4 - The wall shown in Fig. 4.28 is 20 ft long, (a)...Ch. 4 - If the wall in Fig. 4.29 is 4m long, calculate the...Ch. 4 - Refer to Fig. 4.30Ch. 4 - Refer to Fig. 4.31Ch. 4 - Refer to Fig.4.32Ch. 4 - Refer to Fig 4.33Ch. 4 - Refer to Fig. 4.34Ch. 4 - Refer to Fig. 4.35 (?Ch. 4 - Swimming poo!WilierGlasswindow2 ft diameterFigure...Ch. 4 - 4.25 Refer to Fig 4.37Ch. 4 - Refer to Fig.4.38Ch. 4 - Refer to Fig.4.39Ch. 4 - Refer to Fig.4.40Ch. 4 - Refer to Fig 4.41Ch. 4 - figure 4.42i5 shows a gasoline tank filled into...Ch. 4 - If the tank in Fig. 4.42 is filled just to the...Ch. 4 - If the tank in Fig. 4.42 is only half full of...Ch. 4 - For the water tank shown in Fig. 4.43, compute the...Ch. 4 - For the water tank shown in Fig. 4.43, compute the...Ch. 4 - For the water tank shown in Fig. 4.43, compute the...Ch. 4 - For the orange-drink tank shown in Fig. 4.32,...Ch. 4 - For the orange-drink tank shown in Fig. 4.32,...Ch. 4 - For the oil tank shown in Fig. 4.35, compute the...Ch. 4 - For the oil tank shown in Fig. 4.35; compute the...Ch. 4 - figure 4.44 shows a rectangular gate holding water...Ch. 4 - figure 4.45 shows a gate hinged at its bottom and...Ch. 4 - figure 4.46 shows a tank of water with a circular...Ch. 4 - Repeat Problem 4.19(Fig. 4.31), except that the...Ch. 4 - Repeat Problem 4.22 (Fig. 4.32), except that the...Ch. 4 - Repeat Problem 4.26 (Fig. 4.38 ). except that the...Ch. 4 - Repeat Problem 4.28 (Fig. 4.40 ), except that the...Ch. 4 - Use Fig 4.47. The surface is 2.00m long.Ch. 4 - Use Fig.4.48. The surface is 2.50m long.Ch. 4 - Use Fig.4.49. The surface is 5.00 ft longCh. 4 - Use Fig.4.50. The surface is 4.50 ft long.Ch. 4 - Use Fig.4.51.The surface is 4.00 m long.Ch. 4 - Use Fig .4.52. The surface is 1.50m longCh. 4 - Use Fig. 4.53. The surface is 1.50m long.Ch. 4 - Use Fig. 4.54. The surface is 60 in longCh. 4 - Repeat Problem 4.47 using Fig. 4.47, except that...Ch. 4 - Repeat Problem 4.48 using Fig. 4.48, except that...Ch. 4 - The tank in Fig. 4.55 has a view port in the...Ch. 4 - Insulated concrete forms (ICFs) are becoming more...Ch. 4 - Lacks are installed in rivers to allow boats to...Ch. 4 - When a dam is installed in a river that has...Ch. 4 - A wealthy eccentric is interested in having an...Ch. 4 - A pneumatic cylinder like the one shown in Fig....Ch. 4 - Determine the magnitude and the location of the...Ch. 4 - For the hinged gate shown in Fig. 4.61, determine...Ch. 4 - Prob. 4.65PPCh. 4 - Write a program to solve Problem 4.41 with any...Ch. 4 - Write a program to solve Problem 4.42 (Fig. 4.46)...Ch. 4 - Write a program to solve curved surface problems...Ch. 4 - For Program 1, cause the depth h to vary over some...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels are 16 ft on the upstream side and zero on the downstream side. For water, use =62.4lb/ft3.arrow_forwardA man weighs 170 lb on the surface of the earth. Compute his weight in an airplane flying at an elevation of 28 000 ft.arrow_forwardThe inside surface of each thin shell carries a uniform normal pressure of intensity p0. Compute R, the magnitude of the resultant force for each case.arrow_forward
- The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.arrow_forwardThe center of gravity of the plane wire figure is located at G. Determine the lengths a and b.arrow_forwardThe hemispherical glass bowl is filled with water. Find the location y of the center of gravity of the filled bowl. Approximate the bowl as a thin shell of radius R=6.15in. Use 1=162lb/ft3 for glass and 2=62.4lb/ft3 for water.arrow_forward
- Determine the volume of the concrete arch dam.arrow_forwardThe cylindrical water tank with R = 10 ft and H = 1.6 ft has thin steel walls of uniform thickness and weighs 18000 lb when empty. Determine the depth of the water h for which the center of gravity G of the tank plus water will be located at the surface of the water. For water, use =62.4lb/ft3.arrow_forwardThe tank shown in Fig. (1) is divided into two independent chambers. Air pressure is present in both sections. A manometer measures the difference between these pressures. A sphere oi wood (s. = 0.6) is fastened into the wall as shown. a- Compute the magnitude of the resultant of horizontal forces on the sphere. b- Compute the magnitude of the resultant of vertical forces on the sphere. Note : volume of sphere is (n D^3/ 6)arrow_forward
- 10. A trapezoid with parallel bases measur 2m and 4m, respectively. Find the location of its center of gravity, measured from the longer side, if its altitude is 3m. (Solution Needed)arrow_forwardGiven that the weight density of water is 9810 N/m3, calculate the fluid force (in Newtons) on a rectangular 1.6m cross times 2m flat plate submerged horizontally in water at a depth of 4m. Give your answer correct to two decimal places without the units. Round your answer to 2 decimal places.arrow_forwardA swimming pool is filled with 2 m of water. Its bottom is square and measures 4 m on a side. Two opposite sides are vertical; one end is at 45° and the other makes an angle of 60° with the horizontal. Calculate the force of the water on (a) the bottom, (b) a vertical side, (c) the 45° end, and (d) the 60° end. Use the hydrostatic equation.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY