Package: Programmable Logic Controllers with Activities Manual
5th Edition
ISBN: 9781259717550
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 5, Problem 21RQ
Program Plan Intro
NO limit switch:
- Normally Open (NO) limit switch refers to a commonly used industrial control device.
- It is used to operate when a predetermined limit is reached.
- It is actuated by contact with an object such as a cam.
- An electrical symbol used to represent NO limit switch is given below
Solenoid:
- The working of solenoid is based on the principle of magnetic induction.
- It contains a coil, frame, and a plunger known as armature.
- The main function of solenoid is to convert electrical signals into
mechanical motion. - Due to its magnetic movement, solenoid is used in different areas such as locking of two devices, interlocking of gear wheel in automobiles and some other medical application.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Design the hardwired control unit using sequence counter method for 8 instructions. Consider 2 control signals are REQuired for futch operation.
RB4 is connected to a pulse generator and pin RB1 is connected to a led, write a program to toggle the led on the falling and rising edge of the pulse (using interrupts).
Describe How a Time-driven sequence PLC program operates.
Chapter 5 Solutions
Package: Programmable Logic Controllers with Activities Manual
Ch. 5 - What does the memory map for a typical PLC...Ch. 5 - Compare the function of the PLC program and data...Ch. 5 - Prob. 3RQCh. 5 - Prob. 4RQCh. 5 - a. What information is stored in the input image...Ch. 5 - a. What information is stored in the output image...Ch. 5 - Prob. 7RQCh. 5 - List four factors that enter into the length of...Ch. 5 - Prob. 9RQCh. 5 - Prob. 10RQ
Ch. 5 - Prob. 11RQCh. 5 - Answer the following with regard to the Examine If...Ch. 5 - Answer the following with regard to the Examine If...Ch. 5 - Answer the following with regard to the Output...Ch. 5 - A normally closed pushbutton is connected to a PLC...Ch. 5 - Prob. 16RQCh. 5 - Prob. 17RQCh. 5 - Prob. 18RQCh. 5 - Prob. 19RQCh. 5 - Prob. 20RQCh. 5 - Prob. 21RQCh. 5 - Explain the purpose of Windows based programming...Ch. 5 - Prob. 23RQCh. 5 - Prob. 24RQCh. 5 - Prob. 25RQCh. 5 - Prob. 26RQCh. 5 - Assign each of the following discrete input and...Ch. 5 - Prob. 2PCh. 5 - Prob. 3PCh. 5 - Redraw the program shown in Figure 5-57 corrected...Ch. 5 - Redraw the program shown in Figure 5-58 corrected...Ch. 5 - Prob. 6PCh. 5 - Prob. 7PCh. 5 - Prob. 8PCh. 5 - Write the ladder logic program needed to implement...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- Counter implementation using timer 1 module in timer mode.Each incremental value will have delay of last 5 seconds, code should be in Mikro C for PIC16F877A.arrow_forwardUsing the sim8085 write the following code: In a sensor network, three pressure sensors are connected which gives the reading of 4 psi, 8 psi and 10 psi. All the sensor readings are to be summed up and store as a single readingarrow_forwardDraw a plc ladder diagram for blinking lights with start and stop button. Please help me with this. Thank you in advanced.arrow_forward
- Describe the time signal sequence used by 8155 programmable devices when they read or write to an I/O port in handshake mode. Determine the statuses of the status and control words as well. What will the control word for the 8155 timer be?arrow_forwardDiscuss the Interface LED using General Purpose Input Output (GPIO) port. Investigate in further detail the operation of the GPIO ports on the MSP430F5529 Use control logic to manipulate outputs.arrow_forwardDescribe the sequence of timing signals of 8155 programmable devices when it reads or writes to an I/O port in handshake mode. Also determine the states of status word, control word. What will be the control word for 8155 timer?arrow_forward
- As figure shows, please filling the blank to finish the program to turn on the LEDSas following: “D0D2—D1D3—D4D6—D5D7—D0D2D4D6—D1D3D5D7—ALL ON—ALL OFF”, each state lasts 1 second, assuming the oscillator frequency is12MHz, timer1 and timer interrupt must be used.arrow_forwardDesign the interface for a positive logic switch to TM4C123GXL Port A pin 7. Show formulas and calculations for each circuit element. Draw the circuit schematics with components labelled with their names and values. Write the C code as a function to initialize the port for interfacing the switch. Write a function to read the data value of Port A pin 7. Comment your code to explain each initialization step clearly.arrow_forwardConstruct a basic stop/start seal-in circuit. Energize an internal relay to seal-in (latch) the circuit. write the circuit in both Ladder Logic and Function Block Diagram (FBD). Hardware setup: Input 1 - Normally closed stop pushbutton, Input 2 - Normally open start pushbutton. Output 1 - A Red light to indicate the circuit is not energized. Output 2 - A Green light to indicate the circuit is energized. Label all inputs and outputs in the plc program. Write the program in both ladder and function block diagram (FBD).arrow_forward
- Stepper motor control using ULN2003 IC in 16F877 microcontroller will be carried out. In the program, stepper motor and driver IC will be connected to PORTD. to RA0 pin When the connected button is pressed, the stepper motor will turn to the left with half a step and one speed, to pin RA1. When the connected button is pressed, the motor will turn to the right at a certain speed. button connected to RA2 pin When pressed, the motor will be stopped no matter which direction it turns. During engine operation (right or left) If the button connected to the RA3 pin is pressed, the motor speed will double. Working logic Write the program described (solve with ccs)arrow_forwardDraw a PLC ladder logic program that will control a motor in two different directionsarrow_forwardWith AVR ATmega16 microcontroller, a circuit has servomotor (PC0), two pushbuttons and two LEDs. Write a program as: when PB2 pushbutton pressed the servomotor will rotate clockwise and the first LED (PD0) will be on. when PB3 pushbutton pressed the servomotor will rotate counterclockwise and the second LED (PD1) will be onarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning