Fluid Mechanics
8th Edition
ISBN: 9781259165924
Author: Frank White
Publisher: MCGRAW-HILL HIGHER EDUCATION
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.82P
A one-fiftieth-scale model of a military airplane is tested at 1020 m/s in a wind tunnel at sea-level conditions. The model wing area is 180 cm2. The angle of attack is 3°. If the measured model lift is 860 N, what is the prototype lift, using Mach number scaling, when it flies at 10,000 m standard altitude under dynamically similar conditions? Note: Be careful with the area scaling.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A one-tenth-scale model of a supersonic wing tested at 700 m/sin air at 20 ° C and 1 atm shows a pitching moment of 0.25kN ? m. If Reynolds number effects are negligible, what willthe pitching moment of the prototype wing be if it is flying atthe same Mach number at 8-km standard altitude?
In supersonic wind tunnel testing, if different gases areused, dynamic similarity requires that the model and prototypehave the same Mach number and the same( a ) Euler number, ( b ) speed of sound, ( c ) stagnation enthalpy,( d ) Froude number, ( e ) specific-heat ratio
A prototype automobile is designed for cold weather inDenver, CO ( - 10 ° C, 83 kPa). Its drag force is tobe tested on a one-seventh-scale model in a wind tunnelat 150 mi/h, 20 ° C, and 1 atm. If the model and prototypeare to satisfy dynamic similarity, what prototypevelocity, in mi/h, needs to be matched? Comment onyour result.
Chapter 5 Solutions
Fluid Mechanics
Ch. 5 - Prob. 5.1PCh. 5 - A prototype automobile is designed for cold...Ch. 5 - P5.3 The transfer of energy by viscous dissipation...Ch. 5 - When tested in water at 20°C flowing at 2 m/s, an...Ch. 5 - P5.5 An automobile has a characteristic length and...Ch. 5 - P5.6 The disk-gap-band parachute in the...Ch. 5 - Prob. 5.7PCh. 5 - Prob. 5.8PCh. 5 - The Richardson number, Ri, which correlates the...Ch. 5 - Prob. 5.10P
Ch. 5 - Prob. 5.11PCh. 5 - The Stokes number, St, used in particle dynamics...Ch. 5 - Prob. 5.13PCh. 5 - Flow in a pipe is often measured with an orifice...Ch. 5 - The wall shear stress T in a boundary layer is...Ch. 5 - P5.16 Convection heat transfer data are often...Ch. 5 - If you disturb a tank of length L and water depth...Ch. 5 - Prob. 5.18PCh. 5 - Prob. 5.19PCh. 5 - Prob. 5.20PCh. 5 - Prob. 5.21PCh. 5 - As will be discussed in Chap. 11, the power P...Ch. 5 - The period T of vibration of a beam is a function...Ch. 5 - Prob. 5.24PCh. 5 - The thrust F of a propeller is generally thought...Ch. 5 - A pendulum has an oscillation period T which is...Ch. 5 - Prob. 5.27PCh. 5 - Prob. 5.28PCh. 5 - P5.29 When fluid in a pipe is accelerated linearly...Ch. 5 - Prob. 5.30PCh. 5 - P5.31 The pressure drop per unit length in...Ch. 5 - A weir is an obstruction in a channel flow that...Ch. 5 - Prob. 5.33PCh. 5 - Prob. 5.34PCh. 5 - Prob. 5.35PCh. 5 - Prob. 5.36PCh. 5 - Prob. 5.37PCh. 5 - Prob. 5.38PCh. 5 - Prob. 5.39PCh. 5 - Prob. 5.40PCh. 5 - A certain axial flow turbine has an output torque...Ch. 5 - When disturbed, a floating buoy will bob up and...Ch. 5 - Prob. 5.43PCh. 5 - Prob. 5.44PCh. 5 - P5.45 A model differential equation, for chemical...Ch. 5 - P5.46 If a vertical wall at temperature Tw is...Ch. 5 - The differential equation for small-amplitude...Ch. 5 - Prob. 5.48PCh. 5 - P5.48 A smooth steel (SG = 7.86) sphere is...Ch. 5 - Prob. 5.50PCh. 5 - Prob. 5.51PCh. 5 - Prob. 5.52PCh. 5 - Prob. 5.53PCh. 5 - Prob. 5.54PCh. 5 - Prob. 5.55PCh. 5 - P5.56 Flow past a long cylinder of square...Ch. 5 - Prob. 5.57PCh. 5 - Prob. 5.58PCh. 5 - Prob. 5.59PCh. 5 - Prob. 5.60PCh. 5 - Prob. 5.61PCh. 5 - Prob. 5.62PCh. 5 - The Keystone Pipeline in the Chapter 6 opener...Ch. 5 - Prob. 5.64PCh. 5 - Prob. 5.65PCh. 5 - Prob. 5.66PCh. 5 - Prob. 5.67PCh. 5 - For the rotating-cylinder function of Prob. P5.20,...Ch. 5 - Prob. 5.69PCh. 5 - Prob. 5.70PCh. 5 - The pressure drop in a venturi meter (Fig. P3.128)...Ch. 5 - Prob. 5.72PCh. 5 - Prob. 5.73PCh. 5 - Prob. 5.74PCh. 5 - Prob. 5.75PCh. 5 - Prob. 5.76PCh. 5 - Prob. 5.77PCh. 5 - Prob. 5.78PCh. 5 - Prob. 5.79PCh. 5 - Prob. 5.80PCh. 5 - Prob. 5.81PCh. 5 - A one-fiftieth-scale model of a military airplane...Ch. 5 - Prob. 5.83PCh. 5 - Prob. 5.84PCh. 5 - *P5.85 As shown in Example 5.3, pump performance...Ch. 5 - Prob. 5.86PCh. 5 - Prob. 5.87PCh. 5 - Prob. 5.88PCh. 5 - P5.89 Wall friction Tw, for turbulent flow at...Ch. 5 - Prob. 5.90PCh. 5 - Prob. 5.91PCh. 5 - Prob. 5.1WPCh. 5 - Prob. 5.2WPCh. 5 - Prob. 5.3WPCh. 5 - Prob. 5.4WPCh. 5 - Prob. 5.5WPCh. 5 - Prob. 5.6WPCh. 5 - Prob. 5.7WPCh. 5 - Prob. 5.8WPCh. 5 - Prob. 5.9WPCh. 5 - Prob. 5.10WPCh. 5 - Given the parameters U,L,g,, that affect a certain...Ch. 5 - Prob. 5.2FEEPCh. 5 - Prob. 5.3FEEPCh. 5 - Prob. 5.4FEEPCh. 5 - Prob. 5.5FEEPCh. 5 - Prob. 5.6FEEPCh. 5 - Prob. 5.7FEEPCh. 5 - Prob. 5.8FEEPCh. 5 - In supersonic wind tunnel testing, if different...Ch. 5 - Prob. 5.10FEEPCh. 5 - Prob. 5.11FEEPCh. 5 - Prob. 5.12FEEPCh. 5 - Prob. 5.1CPCh. 5 - Prob. 5.2CPCh. 5 - Prob. 5.3CPCh. 5 - Prob. 5.4CPCh. 5 - Does an automobile radio antenna vibrate in...Ch. 5 - Prob. 5.1DPCh. 5 - Prob. 5.2DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A wind tunnel is used to measure the pressure distribution in the airflow over an airplane model. The air speed in the wind tunnel is low enough that compressible effects are negligible. The Bernoulli equation approximation is valid in such a flow situation everywhere except very close to the body surface or wind tunnel wall surfaces and in the wake region behind the model. Far away from the model, the air flows at speed V∞ and pressure P∞, and the air density ? is approximately constant. Gravitational effects are generally negligible in airflows, so we write the Bernoulli equation asP + 1/2 ρV2 = P∞ + 1/2 ρV2∞ Nondimensionalize the equation, and generate an expression for the pressure coefficient Cp at any point in the flow where the Bernoulli equation is valid. Cp is defined as Cp = P−P∞/1/2ρV2arrow_forwardA prototype submarine moves at velocity V, in fresh water at 20 °C, at a 2-m depth, where ambient pressure is 128 kPa. Its critical cavitation number is known to be Ca = 0.25. At what velocity will cavitation bubbles begin to form on the body? Will the body cavitate if V = 30 m/s and the water is cold (5 °C)?arrow_forwarda test tank will be used to measure the drag of a scale model ship 0.8 m long. This model bears full resemblance to a 40 m long prototype ship that was designed to sail at a speed of 10 m / s. a) model speed b) the ratio between model and prototype drag windows c) a ratio between the powers needed to overcome the drag of the model and the prototype take the number of froud into account in your analysis.arrow_forward
- The power P generated by a certain windmill design dependson its diameter D , the air density ρ , the wind velocity V , therotation rate Ω , and the number of blades n . ( a ) Write this relationship in dimensionless form. A model windmill, of diameter50 cm, develops 2.7 kW at sea level when V = 40 m/s andwhen rotating at 4800 r/min. ( b ) What power will be developedby a geometrically and dynamically similar prototype, ofdiameter 5 m, in winds of 12 m/s at 2000 m standard altitude?( c ) What is the appropriate rotation rate of the prototype?arrow_forward5. Consider a Pitot probe in high-speed flow.(c) You are flying through air at static p∞ = 0.8 atm [abs]. Your velocimeter broke,but you are still receiving the following direct stagnation pressure readings (atm[abs]) from the Pitot probe mounted on your aircraft’s noise: i) 3.152 ii) 1.357 iii) 38.428 iv) 0.8 Find the freestream Mach number corresponding to each of the pressure readings. (d) If we are to believe reading (iv), can we step out of the aircraft safely? Why?arrow_forwardThe force, F, acting on a billboard due to wind depends on it length, l, height, h, the modulus of elasticity of the board, E, and the specific weight, γa, of the air. Using dimensional analysis, find an appropriate dimensionless relationship.arrow_forward
- The power P generated by a certain windmill design depends on its diameter D, the air density p, the wind velocity V, the rotation rate w and the number of blades n. a) Write this relationship in dimensionless form. A model windmill of diameter 50 cm develops 2.7 kW at sea level when V=40 m/s and when rotating at 4800 r/min. b) What power will be developed by a geometrically and dynamically similar prototype, of diameter 5 m, in winds of 12 m/s at 2000 m standard altitude? c)What is the appropriate rotation rate of the prototype?arrow_forwardA paramecium is an elongated unicellular organism with approximately 50 μmin diameters and 150 μmin lengths. It swims through water by whip-like movements of cilia, small hairs on the outside of its body. Because it moves "head first" through the water, drag is determined primarily by its diameter and only secondarily by its length, so it's reasonable to model the paramecium as a 70-μm diameter sphere. A paramecium uses 2.0 PW of locomotive power to propel itself through 20∘C water, where 1 pW = 1 picowatt = 10−12W. What is its swimming speed in μm/s? Express your answer in micrometers per second.arrow_forwardA 1:10 scale model study of a torpedo is proposed. Prototype speeds of 90 km/hare to be studied. Should a wind tunnel or a water facility be used?arrow_forward
- Q.10. To predict the drag on an aircraft at a flight speed of 150 m/s, where the condition of air is such that the local speed of sound is 310 m/s, a pressurized low temperature tunnel is used. Density, viscosity and local sonic velocity at tunnel condition are 7.5 kg/m³, 1.22 x 10-5 Ns/m² and 290 m/s. Determine the flow velocity and the scale of the model. Assume full dynamic similarity should be maintained. Density and viscosity at the operating conditions are 1.2 kg/m³ and 1.8 x 10 Ns/m².arrow_forwardA tiny aerosol particle of density ?p and characteristic diameter Dp falls in air of density ? and viscosity ?. If the particle is small enough, the creeping flow approximation is valid, and the terminal settling speed of the particle V depends only on Dp, ? , gravitational constant g, and the density difference (?p − ? ). Use dimensional analysis to generate a relationship for V as a function of the independent variables. Name any established dimensionless parameters that appear in your analysis.arrow_forwardWhen a capillary tube of small diameter D is inserted into a container of liquid, the liquid rises to height h inside the tube (Fig.). h is a function of liquid density ? , tube diameter D, gravitational constant g, contact angle ?, and the surface tension ?s of the liquid. (a) Generate a dimensionless relationship for h as a function of the given parameters. (b) Compare your result to the exact analytical equation for h. Are your dimensional analysis results consistent with the exact equation? Discuss.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License