Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 6, Problem 6.14P
A heavy machine is lowered into a pit by means of a rope wrapped around an 8-in. diameter stationary pole placed horizontally across the top of the pit. The coefficient of static friction for the rope on the pole is 0.35. The rope makes
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A force of 200 N is exerted on a snack box of 5 kg still on the floor. If the coefficient of friction is 0.3, calculate the static friction.
A 150 lb man can climb up15 ft on a 20 ft ladder before it slips. What must the coefficient of friction be if the ladder is arranged so that its base makes an angle of 50 ̊ with the ground? Assume the ladder to be uniform and weighing 100 lb.
A pulley with a diameter of 4 in. can rotate about a fixed shaft with a diameter of 2 in. The coefficient of static friction between the pulley and shaft is 0.20. Determine;
a. the smallest vertical force P required to start raising a 500-lb load.
b. thesmallest vertical force P required to hold the load.
c. the smallest horizontal force P required to start raising the same load.
Chapter 6 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 6 - A 150 Ib block rests on a horizontal floor. The...Ch. 6 - A 200 lb block rests on a horizontal surface. The...Ch. 6 - A tool locker having a mass of 140 kg rests on a...Ch. 6 - A body weighing 100 lb rests on an inclined plane,...Ch. 6 - For Problem 6.4 , compute the friction force F...Ch. 6 - Block A in the figure shown has a mass of 10 kg...Ch. 6 - Compute the horizontal force P required to cause...Ch. 6 - Prob. 6.8PCh. 6 - Calculate the magnitude of the force P, acting as...Ch. 6 - For the block-and-wedge system shown in Figure...
Ch. 6 - Calculate the value of the horizontal force P...Ch. 6 - Two blocks, each having a mass of 100 kg and...Ch. 6 - Calculate the force P required to move the wedges...Ch. 6 - A heavy machine is lowered into a pit by means of...Ch. 6 - Calculate the maximum weight that the person in...Ch. 6 - A flat belt passes halfway around a...Ch. 6 - A belt-and-pulley arrangement has a maximum belt...Ch. 6 - Rework Problem 6.17 for a V-belt with a 40° groove...Ch. 6 - A mass of 320 kg is prevented from falling by a...Ch. 6 - A belt is wrapped around a pulley for 180°. The...Ch. 6 - A jackscrew has a square thread with a pitch of...Ch. 6 - The mean diameter of a square-threaded jackscrew...Ch. 6 - The woodworking vise shown is designed for a...Ch. 6 - A square-threaded screw is used ii a press, shown,...Ch. 6 - For the following computer problems, any...Ch. 6 - Prob. 6.26CPCh. 6 - For the following computer problems, any...Ch. 6 - 6.28 A horizontal force of 18 lb is required to...Ch. 6 - 6.29 A 90-Ib block lying on a rough horizontal...Ch. 6 - 6.30 The tool locker of Problem 6.3 is 0.8 m by...Ch. 6 - Prob. 6.31SPCh. 6 - A 50-lb block rests on a rough inclined plane. If...Ch. 6 - If in Problem 6-32 the plane has an inclination...Ch. 6 - A 325-lb block rests on a plane inclined 25° with...Ch. 6 - A 47 lb body is supported on a plane inclined 33°...Ch. 6 - Prob. 6.36SPCh. 6 - In the figure shown, block A weighs 200 lb and...Ch. 6 - Calculate the magnitude of the horizontal force P,...Ch. 6 - In the figure shown, the coefficient of static...Ch. 6 - A 500-lb block rests on a horizontal surface, as...Ch. 6 - A ladder, 8 m long and having a mass of 25 kg,...Ch. 6 - The ladder shown is supported by a horizontal...Ch. 6 - 6.43 A 16-ft ladder weighing 62 lb (assumed...Ch. 6 - Prob. 6.44SPCh. 6 - 6.45 Compute the minimum weight of block B that...Ch. 6 - Prob. 6.46SPCh. 6 - Prob. 6.47SPCh. 6 - Prob. 6.48SPCh. 6 - Prob. 6.49SPCh. 6 - Prob. 6.50SPCh. 6 - Calculate the force P necessary to start the block...Ch. 6 - A machine having a mass of 500 kg is to be raised...Ch. 6 - 6.53 A ship may exert an estimated pull of 8000 lb...Ch. 6 - A sailor wraps a heavy rope around a bollard (a...Ch. 6 - When a large rope is wrapped twice around a post,...Ch. 6 - A band brake is in contact with drum C through an...Ch. 6 - Prob. 6.57SPCh. 6 - The mean diameter of a square-threaded jackscrew...Ch. 6 - The manually operated apple cider press shown has...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.arrow_forwardA uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.arrow_forwardThe coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.arrow_forward
- Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.arrow_forwardThe square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.arrow_forwardDetermine the smallest horizontal force P that must be applied to block B to cause impending motion. The angles of static friction are 15 between the blocks and 30 between the blocks and the ground.arrow_forward
- The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.arrow_forwardThe test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.arrow_forwardDetermine the smallest coefficient of static friction at A for which the system shown is self-locking (can support the force P of any magnitude). Neglect the weight of bar AB.arrow_forward
- The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.arrow_forwardThe two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.arrow_forwardA block of mass 40 kg is resting on a rough surface. The coefficient of static friction between the surface and block is 0.43. Calculate the minimum force that slide the block from its position.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY