Principles of Foundation Engineering, SI Edition
9th Edition
ISBN: 9781337672085
Author: Das, Braja M., SIVAKUGAN, Nagaratnam
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 6, Problem 6.21P
Consider a continuous foundation of width B = 1.4 m on a sand deposit with c′ = 0, ф′ = 38°, and γ = 17.5 kN/m3. The foundation is subjected to an eccentrically inclined load (see Figure 6.33). Given: load eccentricity e = 0.15 m, Df = 1 m, and load inclination β = 18°. Estimate the failure load Qu(ei) per unit length of the foundation
- a. for a partially compensated type of loading [Eq. (6.89)]
- b. for a reinforced type of loading [Eq. (6.90)]
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Problem 1. A column foundation (Figure below) is 3 m × 2 m in plan. The load on the column,
including the weight of the foundation is 4500 kN. Determin the average vertical stress increase 4
m beneath the corner of the foundation in the soil layer due to the foundation loading by:
a) Boussinesq equations
b) 2:1 method
Given: Df = 1.5 m, Ø'= 25°, c'= 70 kN/m².
1.5 m 1 m
3m x 2m
y = 17 kN/m³
Water level
Ysat 19.5 kN/m³
7.14 Refer to Figure 7.15. For a foundation on a layer of sand, given: B = 5 ft, L = 10 ft,
d = 5 ft, B = 26.6°, e = 0.5 ft, and & = 10°. The Pressuremeter testing at the site pro-
duced a mean Pressuremeter curve for which the pam) versus AR/R, points are as follow.
AR/R.
(1)
P,(m) (lb/in.?)
(2)
0.002
7.2
0.004
24.2
0.008
32.6
0.012
42.4
0.024
68.9
0.05
126.1
0.08
177.65
0.1
210.5
0.2
369.6
What should be the magnitude of Q, for a settlement (center) of 1 in.?
Foundation
BxL
В
Figure 7.15 Definition of parameters-B,
A continuous foundation with a width of 1 m is located on a slope made of clay soil. Refer to Figure 5.19 and let Df = 1 m, H = 4 m, b = 2 m, γ = 16.8 kN/m3, c = cu = 68 kN/m2, Φ= 0, and β = 60°.a. Determine the allowable bearing capacity of the foundation. Let FS = 3.b. Plot a graph of the ultimate bearing capacity qu if b is changed from 0 to 6 m.
Chapter 6 Solutions
Principles of Foundation Engineering, SI Edition
Ch. 6 - For the following cases, determine the allowable...Ch. 6 - A 5.0 ft wide square footing is placed at 3.0 ft...Ch. 6 - Prob. 6.3PCh. 6 - Redo Problem 6.2 using the general bearing...Ch. 6 - The applied load on a shallow square foundation...Ch. 6 - A 2.0 m wide continuous foundation carries a wall...Ch. 6 - Determine the maximum column load that can be...Ch. 6 - A 2.0 m wide strip foundation is placed in sand at...Ch. 6 - A column foundation (Figure P6.9) is 3 m × 2 m in...Ch. 6 - For the design of a shallow foundation, given the...
Ch. 6 - An eccentrically loaded foundation is shown in...Ch. 6 - Prob. 6.12PCh. 6 - For an eccentrically loaded continuous foundation...Ch. 6 - A 2 m 3 m spread footing placed at a depth of 2 m...Ch. 6 - Prob. 6.15PCh. 6 - A tall cylindrical silo carrying flour is to be...Ch. 6 - A 2.0 m 2.0 m square pad footing will be placed...Ch. 6 - An eccentrically loaded continuous foundation is...Ch. 6 - A square foundation is shown in Figure P6.19. Use...Ch. 6 - The shallow foundation shown in Figure 6.25...Ch. 6 - Consider a continuous foundation of width B = 1.4...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- 3. A square foundation is constructed in a soil deposit as shown in the figure below. Assume that the groundwater table is 6 meters below the foundation. The applied load on the shallow square foundation makes an angle of 10° with the vertical. Use FS = 3 and determine the allowable load. (Use general bearing capacity equation.) 2 m 6 m 4 m y = 17.5 kN/m³ p' = 33° c' = 20 kN/m² Ysat = 20k N/m³ Groundwater tablearrow_forwardRefer to Figure 5.2 and consider a rectangular foundation. Given: B = 1.5 m, L = 2.5 m, Df = 1.2 m, H = 0.9 m, Φ' = 40º, c' = 0, and γ = 17 kN/m3. Using a factor of safety of 3, determine the gross allowable load the foundation can carry. Use Eq. (5.3).arrow_forward3. A square foundation is constructed in a soil deposit as shown in the figure below. Assume that the groundwater table is 6 meters below the foundation. The applied load on the shallow allowable load. (Use general bearing capacity equation.) square foundation makes an angle of 10° with the vertical. Use FS 3 and determine the 2 m 6 m 4 m y = 17.5 kN/m³ 4' = 33° c' = 20 kN/m² Ysat = 20k N/m³ Groundwater tablearrow_forward
- A continuous foundation, supported by sand, has a width of 2 m and the depth of foundation is 1.5m. The known soil characteristics are as follows: ϕ’ = 40°, c’ = 0, and γ = 16.5 kN/m³. If the loadeccentricity is 0.2 m, determine the ultimate load per unit length of the foundation.(Ans: ???? =5,260??)arrow_forwardH.W 2.pdf > H.Q 6 A flexible foundation measuring 1.5 m x 3 m is supported by a saturated clay. Given: Dr = 1.2 m, H = 3 m, Es (clay)= 600 kN/m2, and qo = 150 kN/m?. Determine the average elastic settlement of the foundation. H.O 7 Figure 7.3 shows a foundation of 10 ft x 6.25 ft resting on a sand deposit. The net load per unit area at the level of the foundation, qo, is 3000 Ib/ft?. For the sand, u, = 0.3, Es = 3200 Ib/in?, Df = 2.5 ft, and H = 32 ft. Assume that the foundation is rigid and determine the elastic settlement the foundation would undergo. H.O 8 Determine the net ultimate bearing capacity of mat foundations with the following characteristics: c, = 2500 Ib/ft, = 0, B = 20 ft, L = 30 ft, D, = 6.2 ft Foundation Engineering I H.W 2 H.O 9 A 20-m-long concrete pile is shown in Figure below. Estimate the ultimate point load Q, by a. Meyerhof's method b. Coyle and Castello's method Concrete pile 460 mm x 460 mm Loose sand 20m y I86 ANi Dee s H.O 10 A concrete pile 20 m long…arrow_forwardA long foundation 0.6 m wide carries a line load of 100 kN/m. Calculate the vertical stressi ncrease at a point P, the coordinates of which are x = 2.5 m, and z = 1.5m, where the x-coordinate is normal to the line load from the central line of the footing. a. 3.05 kPa b. 1.69 kPa c. 4.08 kPa d. 5.12 kPa) e. 2.55 kPaarrow_forward
- An eccentrically loaded continuous foundation is shown in Figure P4.11. Determine the ultimate load Qu per unit length that the foundation can carry. Use the reduction factor method [Eq. (4.63)].arrow_forwardFor the rigid shallow foundation (2*4m) shown in Fig, calculate Immediate settlement the center of the foundation if . (net pressure qo = 100 kPa. Assume 0.3 X 2 m 0.5 m 3.5 m W.T Q=2000 kN 6 m-3 m y=22 kN/m² Ce=0.805 C₁ = 0.3 e=0.753 OCR = 1.4 G. s Dense Sand Y = 22 kN/m³ Silty Clay Silty Sand Y = 18 kN/m²arrow_forwardRefer to Figure 5.2. A square foundation measuring 1.5 m x 1.5 m is supported by a saturated clay layer of limited depth underlain by a rock layer. Given that Df = 1 m, H = 0.7 m, cu = 115 kN/m2, and γ = 18.5 kN/m3, estimate the ultimate bearing capacity of the foundation.arrow_forward
- Question 1) For a shallow foundation measuring (1.7 m x 2.2 m) as shown below: , A. Estimate the elastic settlement proposed by Mayerhof. Then, B. Estimate the elastic settlement proposed by Bowles, if the water table rises 1.5 m. Then, Use yw=10 kN/m³ qnet= 1.2 MN/m2 G.S 1.5 m Sand Yd=16 kN/m³ Ysat= 17 kN/m3 %3D 2.5 m N60=52 V W.T. Silty Sand Ya=18 kN/m³ Ysat = 18.5 kN/m? N60=52 3.5 m Sand Ya=19 kN/m3 Ysat = 22 kN/m³ e, = 0.4, Ae=0.04 , o'= 194 kN/m2 5 m Cc= 0.3, Cs= 0.2 , Ca= 0.05 N60=60 CS Scanned with CamScannerarrow_forwardA 8 m layer of sand, of saturated unit weight 22 kN/m3, overlies a 6 m layer of clay, of saturated unit weight 27 kN/m3. A foundation carrying 1200 KN load is to be founded on the soil layer. If the clay is normally consolidated and the increase in effective pressure due to the foundation load at the center of clay is 27 kN/m2, Soil parameters are Cc = 0.25, eo = 1.0. Assume required data •Draw the soil profile diagram in detail, mentioning all the soil properties with the foundation details. •Calculate the consolidation settlement at the center of the clay layer.arrow_forwardA square flexible foundation of width B = 2 m applies a uniform pressure of 17 kN/m² to the underlaying ground. Determine the vertical stress increase using at a depth of 1m below the center using: a) 2:1 method b) M and N method c) Stress isobars d) Newmark Methodarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Types of Foundation in building construction in detail - Civil Engineering Videos; Author: Civil Engineers;https://www.youtube.com/watch?v=7sl4KuM4UIE;License: Standard YouTube License, CC-BY
Types of Foundation || Foundation Engineering; Author: Civil Engineering;https://www.youtube.com/watch?v=AFLuAKGhanw;License: Standard Youtube License