MORTON SALT
Introduction
Morton Salt is a subsidiary of Morton International, a manufacturer of specialty chemicals, air bags, and salt products. The Morton salt-processing facility in Silver Springs, New York, between Buffalo and Rochester, is one of six similar Morton salt-processing facilities in the United States. The Silver Springs plant employs about 200 people, ranging from unskilled to skilled. It produces salt products for water conditioning, grocery, industrial, and agricultural markets. The grocery business consists of 26-oz. round cans of iodized salt. Although the grocery business represents a relatively small portion of the total output (approximately 15 percent), it is the most profitable.
Salt production
The basic raw material, salt, is obtained by injecting water into salt caverns that are located some 2,400 feet below the surface. There, the salt deposits dissolve in the water. The resulting brine is pumped to the surface where it is converted into salt crystals. The brine is boiled, and much of the liquid evaporates, leaving salt crystals and some residual moisture, which is removed in a drying process. This process is run continuously for about six weeks at a time. Initially, salt is produced at the rate of 45 tons per hour. But the rate of output decreases due to scale buildup, so that by the sixth week, output is only 75 percent of the initial rate. At that point, the process is halted to perform maintenance on the equipment and remove the scale, after which salt production resumes.
The salt is stored in silos until it is needed for production, or it is needed for production, or it is shipped in bulk to industrial customers. Conveyors move the salt to each of the four dedicated production areas, one of which is round can production (see diagram.). The discussion here focuses exclusively on round can production.
Round Can Production
Annual round can production averages roughly 3.8 million cans. Approximately 70 percent of the output is for the Morton label, and the rest is for private label. There are two parallel, high-speed production lines. The lines share common processes at the beginning of the lines, and then branch out into two identical lines. Each line is capable of producing 9,600 cans per hour (160 cans per minute). The equipment is not flexible, so the production rate is fixed. The operations are completely standardized; the only variable is the brand label that is applied. One line requires 12 production workers, while both lines together can be operated by 18 workers because of the common processes. Workers on the line perform low-skilled, repetitive tasks.
The plant produces both the salt and the cans the salt is packaged in. The cans are essentially a cylinder with a top and a bottom; they are made of cardboard, except for a plastic pour spout in the top. The cylinder portion is formed from two sheets of chip board that are glued together and then rolled into a continuous tube. The glue not only binds the material, it also provides a moisture barrier. The tube is cut in a two-step process. It is first cut into long sections, and those sections are then cut into can-size pieces. The top and bottom pieces for the cans are punched from a continuous strip of cardboard. The separate pieces move along conveyor belts to the lines where the components are assembled into cans and glued. The cans are then filled with salt and the pour spout is added. Finally, the cans are loaded onto pallets and placed into inventory, ready to be shipped to distributors.
Quality
Quality is checked at several points in the production process. Initially, the salt is checked for purity when it is obtained from the wells, Iodine and an anti-caking compound are added to the salt, and their levels are verified using chemical analysis. Crystal size is important. In order to achieve the desired size and to remove lumps, the salt is forced through a scraping screen, which can cause very fine pieces of metal to mix with the salt. However, these pieces are effectively removed by magnets that are placed at appropriate points in the process. If, for any reason, the salt is judged to be contaminated, it is diverted to a nonfood product.
Checking the quality of the cans is done primarily by visual inspection, including verifying the assembly operation is correct, checking filed cans for correct weight, inspecting cans to see that labels are labels are properly aligned, and checking to see that plastic pour spouts are correctly attached.
The equipment on the production line is sensitive to misshapen or damaged cans, and frequently jams, cussing production delays. This greatly reduces the chance of a defective can getting through the process, but it reduces productivity, and the salt in the defective cans must be scrapped. The cost of quality is fairly high, owing to the amount of product that is scrapped, the large number of inspectors, and the extensive laboratory testing that is needed.
Production Planning and Inventory
The plant can sell all of the salt it produces. The job of the production
Equipment Maintenance and Repair
The equipment is 1950s vintage, and it requires a fair amount of maintenance to keep it in good working order. Even so, breakdowns occur as parts wear out. The plant has its own tool shop where skilled workers repair parts or make new parts because replacement parts are no longer available for the old equipment.
3. What are some of the possible reasons why the company continues to use the old processing equipment instead of buying new, more modern equipment?
Want to see the full answer?
Check out a sample textbook solutionChapter 6 Solutions
Operations Management
- The Winston Company has four distribution centers (A, B, C, and D) that require 40,000, 60,000, 30,000, and 50,000 gallons of de-ionized water, respectively, per month for cleaning their long-haul trucks. Three de-ionized water wholesalers (1, 2, and 3) indicated their willingness to supply as many as 50,000, 70,000, and 60,000 gallons, respectively. The total cost (shipping plus price) of delivering 1,000 gallons of de-ionized water from each wholesaler to each distribution center is shown in the following table: Distribution Center Wholesaler A B 1 $1.70 $1.90 $1.60 $1.70 2 $1.40 $1.90 $1.60 $1.70 3 $1.60 $1.50 $1.80 $1.40 a. Which of the following statements regarding setting up the tableau for the optimal solution for this problem is true? O A. The sum of supply capacities is greater than the sum of demands, so a dummy distribution center needed, O B. The sum of supply capacities is less than the sum of demands, so a dummy wholesaler is needed. C. The sum of supply capacities…arrow_forwardThe Winston Company has four distribution centers (A, B, C, and D) that require 40,000, 60,000, 30,000, and 50,000 gallons of de-ionized water, respectively, per month for cleaning their long-haul trucks. Three de-ionized water wholesalers (1, 2, and 3) indicated their willingness to supply as many as 50,000, 70,000, and 60,000 gallons, respectively. The total cost (shipping plus price) of delivering 1,000 gallons of de-ionized water from each wholesaler to each distribution center is shown in the following table: Distribution Center Wholesaler A B C D 1 $1.30 $1.40 $1.80 $1.60 2 $1.30 $1.50 $1.80 $1.60 3 $1.60 $1.40 $1.70 $1.50 a. Determine the optimal solution. Show that all capacities have been exhausted and that all demands can be met with this solution. b. What is the total cost of the solution?arrow_forwardThe Winston Company has four distribution centers (A, B, C, and D) that require 40,000, 60,000, 30,000, and 50,000 gallons of de-ionized water, respectively, per month for cleaning their long-haul trucks. Three de-ionized water wholesalers (1, 2, and 3) indicated their willingness to supply as many as 50,000, 70,000, and 60,000 gallons, respectively. The total cost (shipping plus price) of delivering 1,000 gallons of de-ionized water from each wholesaler to each distribution center is shown in the following table: Distribution Center Wholesaler A B D $1.90 $1.90 $1.70 $1.60 $1.70 2 $1.40 $1.60 $1.70 3 $1.60 $1.50 $1.80 $1.40 a. Which of the following statements regarding setting up the tableau for the optimal solution for this problem is true? O A. The sum of supply capacities is greater than the sum of demands, so a dummy distribution center is needed. O B. The sum of supply capacities is less than the sum of demands, so a dummy wholesaler is needed. O C. The sum of supply capacities…arrow_forward
- Three doctors have banded together to form a jointpractice: the Port Charles Trio. The overhead for the practiceis $40,000 per year. Each doctor brings in annual revenuesand incurs annual variable costs as follows: doctor 1—$155,000 in revenue, $40,000 in variable cost; doctor 2—$160,000 in revenue, $35,000 in variable cost; and doctor3—$140,000 in revenue, $38,000 in variable cost.The Port Charles Trio wants to use game theory todetermine how much each doctor should be paid. Determinethe relevant characteristic function and show that the coreof the game consists of an infinite number of points. Alsodetermine the Shapley value of the game. Does the Shapleyvalue give a reasonable division of the practice’s profits?arrow_forwardwhy Meat Production and Supply Chain under COVID-19 interesting and economically significant.arrow_forwardExplain in detail the core opreations of port warehouses.arrow_forward
- Gabriela Manufacturing must decide whether to insourceor outsource a new toxic-free miracle carpet cleaner that workswith its Miracle Carpet Cleaning Machine. If it decides toinsource the product, the process would incur $300,000 of annualfixed costs and $1.50 per unit of variable costs. If it is outsourced,a supplier has offered to make it for an annual fixed cost of$120,000 and a variable cost of $2.25 per unit in variable costs.(a) Given these two alternatives, determine the indifferencepoint (where total costs are equal).(b) If the expected demand for the new miracle cleaner is300,000 units, what would you recommend that GabrielaManufacturing do?arrow_forwardcomparative and competitve advantages of Port of Vancouver, in comparision with other competing portsarrow_forwardTravel Passengers 1 405 2 410 3 420 4 415 5 412 6 420 7 424 8 433 9 438 10 440 11 446 12 451 13 455 14 464 15 466 16 474 17 476 18 482 a) Using a weighted moving average with three periods, determine the sales for day 15. Use 3, 2, and 1 for the weights of the most recent, second most recent, and third most recent periods, respectively b) Find the MAD, MSE and MAPE b) Use exponential smoothing with a smoothing constant of 0.50 to forecast the sales (Assume that last period’s forecast for period 1 is equal to actual to begin the procedure (Ft1=Yt1). Which method do you think is best? Is this an improvement over the weighted average- use MAD onlyarrow_forward
- You are to set up a linear programarrow_forward8 Factors that influence a business locationarrow_forward1. According to Weber's classification of industries, where should a facility that makes concrete be located? A. Located near the market. B. Located near the raw material sources. C. Not necessarily located at markets or raw material sources. 2.According to Weber's classification of industries, where should a car assembly facility be located? A. Not necessarily located at markets or raw material sources. B. Located near the raw material sources. C. Located near the market.arrow_forward
- Purchasing and Supply Chain ManagementOperations ManagementISBN:9781285869681Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. PattersonPublisher:Cengage Learning