The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target. Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Question

Want to see the full answer?

Answer 1

Question

Chapter 6.S, Problem 4P

a)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

b)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are three standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Rosters Chicken advertises " lite" chicken with 30% fewer calories than standard chicken. When the process for "lite" chicken breast production is in control, the average chicken breast contains 420 calories, and the standard deviation in caloric content of the chicken breast population is 25 calories. Rosters wants to design an x-chart to monitor the caloric content of chicken breasts, where 25 chicken breasts would be chosen at random to form each sample.a) What are the lower and upper control limits for th.is chart if these limits are chosen to be four standard deviations from the target?b) What a re the limits with three standard deviations from the target?

What is the difference between acceptance sampling andprocess control?

In a sausage factory, quality managers are studying the compliance of the sausages with the requirements. Any sausage having pin holes, air pockets, deformation or breakage in its casings is counted as defective and total number of such defective sausages alone is noted in each shift. The following data represents the number of defective sausages in samples of 200 sausages taken from 10 shifts. Sample Defectives Percent Defective 1 40 20% 2 28 14% 3 15 8% 4 23 (a) 5 20 10% 6 21 11% 7 19 10% 8 15 8% 9 16 8% 10 17 9% Calculate the value for (a) in the table above. Calculate p-bar based on the samples above. What is the UCL and LCL for a p chart based on the data provided and a desired control level of 99.74%? Use your control limits from part b along with the data provided to draw a p-chart. Is the process in control? Why or why not? If not in control, suggest some potential reasons.

Answer 2

Question

Chapter 6.S, Problem 4P

a)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

b)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are three standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 3

Question

Chapter 6.S, Problem 4P

a)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

b)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are three standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 4

Question

Chapter 6.S, Problem 4P

a)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

b)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are three standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 5

Chapter 6.S, Problem 4P

a)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

b)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are three standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Answer 6

Chapter 6.S, Problem 4P

a)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Answer 7

Chapter 6.S, Problem 4P

a)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Answer 8

b)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are three standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Answer 9

b)

Summary Introduction

To determine: The upper control limit and lower control limit for the chart if the control limits are three standard deviation from the target.

Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Answer 10

Expert Solution & Answer

Answer 11

Expert Solution & Answer

Answer 12

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 13

Ch. 6.S - Prob. 1DQ Ch. 6.S - Define in statistical control.Ch. 6.S - Prob. 3DQ Ch. 6.S - Prob. 4DQ Ch. 6.S - Prob. 5DQ Ch. 6.S - Prob. 6DQ Ch. 6.S - Prob. 7DQ Ch. 6.S - Prob. 8DQ Ch. 6.S - Prob. 9DQ Ch. 6.S - Prob. 10DQ

The upper control limit and lower control limit for the chart if the control limits are four standard deviation from the target. Introduction: Control charts used to determine whether the process is under control or not. Attributes and variables are the factors under the control charts.

Solution Summary: The author explains how to determine the upper and lower control limits for a control chart if the controls are four standard deviations from the target.

Concept explainers

Want to see the full answer?

Chapter 6 Solutions