Operations Management: Sustainability and Supply Chain Management (12th Edition)
12th Edition
ISBN: 9780134130422
Author: Jay Heizer, Barry Render, Chuck Munson
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 6.S, Problem 51P
Summary Introduction
To determine: The average outgoing quality
Introduction: Statistical process control is the method that helps to measure and control the quality during the process of production.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A researcher wishes to estimate the proportion of fish in a certain lake that is inedible due to pollution of the lake. How large a sample should be tested in order to be 99% confident that the true proportion of inedible fish is estimated to within 8%?
C-Spec, Inc., is attempting to determine whether an existing machine is capable of milling an engine part that has a key specification of 4 ± .003 inches. After a trial run on this machine, C-Spec has determined that the machine has a sample mean of 4.001 inches witha standard deviation of .002 inch. (Answer in Appendix D)a. Calculate the Cpk for this machine.b. Should C-Spec use this machine to produce this part? Why?
Design specifications require that a key dimension on a product measure 100kg plus and minus 3kg. If the value of the quality exceeds the target by the tolerance of 3kg on either side, the product will be likely to fail during the warranty period and cost $480 for repair. A process being considered for producing this product has a standard deviation of 1.5kg
A) Compute the process capability ratio if the process is centered. Is it capable to meet the quality specification? Explain.
B) Suppose the original process average shifts to 99kg, maintaining the current dispersion. Calculate the process capability index after the shift. Is it capable?
C) What is the average loss per unit after the shift as in (part b)? Use Taguchi loss function for multi-products case
Chapter 6 Solutions
Operations Management: Sustainability and Supply Chain Management (12th Edition)
Ch. 6.S - Prob. 1DQCh. 6.S - Define in statistical control.Ch. 6.S - Prob. 3DQCh. 6.S - Prob. 4DQCh. 6.S - Prob. 5DQCh. 6.S - Prob. 6DQCh. 6.S - Prob. 7DQCh. 6.S - Prob. 8DQCh. 6.S - Prob. 9DQCh. 6.S - Prob. 10DQ
Ch. 6.S - Prob. 11DQCh. 6.S - Prob. 12DQCh. 6.S - Prob. 13DQCh. 6.S - Prob. 14DQCh. 6.S - Prob. 15DQCh. 6.S - Prob. 16DQCh. 6.S - Prob. 17DQCh. 6.S - What does the formula L = D2C mean?Ch. 6.S - Prob. 19DQCh. 6.S - An avant-garde clothing manufacturer runs a series...Ch. 6.S - Prob. 2PCh. 6.S - Prob. 3PCh. 6.S - Prob. 4PCh. 6.S - Prob. 5PCh. 6.S - Develop a flowchart [as in Figure 6.6 (e) and...Ch. 6.S - Prob. 7PCh. 6.S - Prob. 8PCh. 6.S - Prob. 9PCh. 6.S - Prob. 10PCh. 6.S - Prob. 11PCh. 6.S - Prob. 12PCh. 6.S - Prob. 13PCh. 6.S - Prob. 14PCh. 6.S - Prob. 15PCh. 6.S - Prob. 16PCh. 6.S - Prob. 17PCh. 6.S - Prob. 18PCh. 6.S - Prob. 19PCh. 6.S - Prob. 20PCh. 6.S - Prob. 21PCh. 6.S - Prob. 22PCh. 6.S - Prob. 23PCh. 6.S - Prob. 24PCh. 6.S - Prob. 25PCh. 6.S - Prob. 40PCh. 6.S - Prob. 41PCh. 6.S - Prob. 42PCh. 6.S - Prob. 43PCh. 6.S - Prob. 44PCh. 6.S - Prob. 45PCh. 6.S - Prob. 51PCh. 6.S - Prob. 52PCh. 6.S - Prob. 26PCh. 6.S - Prob. 27PCh. 6.S - Prob. 53PCh. 6.S - Prob. 54PCh. 6.S - Prob. 55PCh. 6.S - Prob. 1CSCh. 6.S - Prob. 2CSCh. 6.S - Prob. 1.1VCCh. 6.S - Prob. 1.2VCCh. 6.S - Prob. 1.3VCCh. 6.S - Prob. 2.1VCCh. 6.S - Prob. 2.2VCCh. 6.S - Prob. 2.3VCCh. 6.S - Prob. 2.4VCCh. 6 - Prob. 1DQCh. 6 - Prob. 2DQCh. 6 - Prob. 3DQCh. 6 - Prob. 4DQCh. 6 - Prob. 5DQCh. 6 - Prob. 6DQCh. 6 - Prob. 7DQCh. 6 - Prob. 8DQCh. 6 - Prob. 9DQCh. 6 - Prob. 10DQCh. 6 - Prob. 11DQCh. 6 - Prob. 12DQCh. 6 - Prob. 13DQCh. 6 - Prob. 14DQCh. 6 - Prob. 15DQCh. 6 - Prob. 16DQCh. 6 - Prob. 17DQCh. 6 - Prob. 18DQCh. 6 - An avant-garde clothing manufacturer runs a series...Ch. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Kathleen McFaddens restaurant in Boston has...Ch. 6 - Develop a flowchart [as in Figure 6.6 (e) and...Ch. 6 - Prob. 7PCh. 6 - Prob. 8PCh. 6 - Prob. 9PCh. 6 - Prob. 10PCh. 6 - Prob. 11PCh. 6 - Prob. 12PCh. 6 - Prob. 13PCh. 6 - Prob. 14PCh. 6 - Prob. 15PCh. 6 - Prob. 16PCh. 6 - Prob. 17PCh. 6 - Prob. 1CSCh. 6 - How could the survey have been more useful?Ch. 6 - Prob. 3CSCh. 6 - Prob. 1.1VCCh. 6 - Prob. 1.2VCCh. 6 - Prob. 1.3VCCh. 6 - Prob. 1.4VCCh. 6 - Prob. 2.1VCCh. 6 - Prob. 2.2VCCh. 6 - Prob. 2.3VCCh. 6 - Prob. 2.4VCCh. 6 - Prob. 2.5VC
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, operations-management and related others by exploring similar questions and additional content below.Similar questions
- In the past, Alpha Corporation has not performed incoming quality control inspections but has taken the word of its vendors. However, Alpha has been having some unsatisfactory experience recently with the quality of purchased items and wants to set up sampling plans for the receiving department to use. For a particular component, X, Alpha has a lot of tolerance percentage defective of 10 percent. Zenon Corporation, from which Alpha purchases this component, has an acceptable quality level in its production facility of 3 percent for component X. Alpha hasa consumer’s risk of 10 percent and Zenon has a producer’s risk of 5 percent.a. When a shipment of product X is received from Zenon Corporation, what sample size should the receiving department test?b. What is the allowable number of defects in order to accept the shipment?arrow_forwardAn operator wants to determine the standard deviation for a machine she operates. To do this, she wants to create a p-chart. Over a month's time, she collects 30 samples of 75 observations each and records the number of errors. The average proportion defective is found to be 0.024. Which of the following is the standard deviation () of the machine? a. More than 0.5 but less than or equal to 1.0 b. More than 1.0 c. Less than or equal to 0.1 d. More than 0.1 but less than or equal to 0.5arrow_forwardAs the supervisor in charge of shipping and receiving,you need to determine the average outgoing quality in a plantwhere the known incoming lots from your assembly line havean average defective rate of 3%. Your plan is to sample 80 unitsof every I ,000 in a lo t. The number of defects in the sample isnot to exceed 3. Such a plan provides you with a probabilityof acceptance of each lot of . 79 (79%). What is your averageoutgoing quality?arrow_forward
- In the past, Alpha Corporation has not performed incoming quality control inspections but has taken the word of its vendors. However, Alpha has been having some unsatisfactory experience recently with the quality of purchased items and wants to set up sampling plans for the receiving department to use. For a particular component, X, Alpha has a lot tolerance percentage defective of 10 percent. Zenon Corporation, from which Alpha purchases this component, has an acceptable quality level in its production facility of 3 percent for component X. Alpha has a consumer's risk of 10 percent and Zenon has a producer's risk of 5 percent. When a shipment of Product X is received from Zenon Corporation, what sample size should the receiving department test? Use Exhibit 10.16. Note: if the exact value of the computed LTPD ÷ AOQ ratio does not appear in Exhibit 10.16, use the next higher ratio. Note: Round up your answer to the next whole number. What is the allowable number of defects in…arrow_forwardSuppose that a quality characteristic is normally distributed with specifications at 100 ± 20. The process standard deviation is 6.(a) Suppose that the process mean is 100. What are the natural tolerance limits? Calculate Cp and Cpk and interpret these ratios. What fraction of parts do you expect to be defective?(b) Suppose that the process mean is 106. What are the natural tolerance limits? What is thefraction defective? Calculate Cp and Cpk and interpret these ratios.arrow_forwardFrom a perspective of Statistical Process Control (SPC), a six-sigma process will have which of the following attributes? a The USL and LSL will be separated by a distance of six sigma b The process center will be aligned with the LSL c The number of defects produced by the process will be 0.0018 parts per million d All of the abovearrow_forward
- Design specifications require that a key dimension on a product measure 100kg plus and minus 3kg. If the value of the quality exceeds the target by the tolerance of 3kg on either side, the product will be likely to fail during the warranty period and cost $480 for repair. A process being considered for producing this product has a standard deviation of 1.5kg A) Compute the process capability ratio if the process is centered. Is it capable to meet the quality specification? Explain. B) If the original process in (part A) is incapable, what should be the standard deviation of the process to make it capable? C) Suppose the original process average shifts to 99kg, maintaining the current dispersion. Calculate the process capability index after the shift. Is it capable? D) What is the average loss per unit after the shift as in (part c)? Use Taguchi loss function for multi-products casearrow_forward4. C-Spec, Inc., is attempting to determine whether an existing machine is capable of milling an engine part that has a key specification of 4 ± 0.003 inches. After a trial run on this machine, C-Spec has determined that the machine has a sample mean of 4.001 inches with a standard deviation of 0.002 inch. a. Calculate the capability ratio for this machine. b. Calculate the capability index for this machine c. Should C-Spec use this machine to produce this part? d. Explain why? e. Show computationarrow_forwardAspen Plastics produces plastic bottles to customer order. The quality inspector randomly selects four bottles from the bottle machine and measures the outside diameter of the bottleneck, a critical quality dimension that determines whether the bottle cap will fit properly. The dimensions (inch) from the last six samples are: BOTTLE Sample 1 2 3 4 1 0.694 0.622 0.698 0.69 2 0.687 0.611 0.697 0.613 3 0.671 0.680 0.695 0.602 4 0.610 0.615 0.685 0.678 5 0.680 0.624 0.618 0.614 6 0.685 0.693 0.607 0.669 What would be the center line of a 3-sigma S chart? Answer:arrow_forward
- In an acceptance sampling plan developed for lots containing 1,000 units, the sample size n is 85. The percent defec-tive of the incoming lots is 2%, and the probability of acceptance is 0.64. What is the average outgoing quality?arrow_forwardYou want to determine the control lines for a "p" chart for quality control purposes. If the total number of defects from all samples is 2,500, the number of samples is 100, and the sample size is 40, which of the following would be the standard deviation used in developing the control lines? Answers: 0.0484 0.2499 0.00687 0.00707 0.00765arrow_forwardThe specifications for a gasket that installs between two engine parts calls for a thickness of 6.0 mm ± .2 mm. The standard deviation of the process is estimated to be 0.05 mm. The process is known to operate at a mean thickness of 6.1 mm What are the upper and lower specification limits for the gasket? What are the Cp and Cpk values for this process? Is this process capable of producing the desired part?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Practical Management ScienceOperations ManagementISBN:9781337406659Author:WINSTON, Wayne L.Publisher:Cengage,Operations ManagementOperations ManagementISBN:9781259667473Author:William J StevensonPublisher:McGraw-Hill EducationOperations and Supply Chain Management (Mcgraw-hi...Operations ManagementISBN:9781259666100Author:F. Robert Jacobs, Richard B ChasePublisher:McGraw-Hill Education
- Purchasing and Supply Chain ManagementOperations ManagementISBN:9781285869681Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. PattersonPublisher:Cengage LearningProduction and Operations Analysis, Seventh Editi...Operations ManagementISBN:9781478623069Author:Steven Nahmias, Tava Lennon OlsenPublisher:Waveland Press, Inc.
Practical Management Science
Operations Management
ISBN:9781337406659
Author:WINSTON, Wayne L.
Publisher:Cengage,
Operations Management
Operations Management
ISBN:9781259667473
Author:William J Stevenson
Publisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...
Operations Management
ISBN:9781259666100
Author:F. Robert Jacobs, Richard B Chase
Publisher:McGraw-Hill Education
Purchasing and Supply Chain Management
Operations Management
ISBN:9781285869681
Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson
Publisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...
Operations Management
ISBN:9781478623069
Author:Steven Nahmias, Tava Lennon Olsen
Publisher:Waveland Press, Inc.