LogixPro PLC Lab Manual for Programmable Logic Controllers
5th Edition
ISBN: 9781259680847
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 7, Problem 11P
Program Plan Intro
Anti-tie down circuit:
The term “anti-tie down circuit” refers to a non-repetitive circuit which enables the circuit to operate for one cycle. The circuit must be activated by pushing both start buttons to operate the cycle each time.
Timer ON Delay (TON):
- TON refers to an on-delay timer.
- The on-delay timer is the most commonly used timer.
- TON counts the time-based intervals as soon as the instruction becomes true.
- Here, the output changes its state from low to high when the timer provides some time delay (instruction goes from OFF to ON state).
Given:
Assume that the two palm start buttons are named as “SW1” and “SW2”. It is given that both buttons should be pressed at the same time within 0.5 seconds. It is also given that the circuit does not allow operating the press with one button.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Implement the counter increment and return to the beginning of the loop. When you finish these stages, you should have the fundamental structure of the counter control loop established, and your code should look like this:.text li $s0, 0 lw $s1, n start_loop: sle $t1, $s0, $s1 beqz $t1, end_loop
# code block addi $s0, $s0, 1 b start_loop end_loop:.datan:.word 5
write a code that decodes the coloured bands on a resistor.Each colour band printed on a resistor has a corresponding numeric value, as shown in the table below:
Colour
Numeric value
black
0
brown
1
red
2
orange
3
yellow
4
green
5
blue
6
violet
7
grey
8
white
9
To calculate the total resistance value, the following formula should be used:
resistance=(10a+b)⋅10^c
where a, b, and c are the numeric values of the first, second, and third colour bands respectively.
For example, let's say that the colour bands on a resistor are red-green-orange. In this case, a=2, b=5, and c=3 (using the table). Hence the resistance value is 25000 ohms:
resistance=(10*2+5)⋅10^3=25000 ohms
Your task is to write a program which asks the user to input the three colour bands. The program should then calculate and output the resistance value indicated by the bands.
As part of your solution, you must define and use a function named colour_to_number. This function should take one…
Some Computer Science students who do the Computer Logic and Digital Design module sometimes find it difficult to carry out arithmetic operations using various bases. As such, the plan among the group is to design a digital expression evaluator. The circuit would allow the user to input the required numbers in either decimal, binary, octal or hexadecimal as well as the operator be used (+, -, *, /) and perform the calculation. The user is also able to indicate the base in which the answer is required (restricted to decimal, binary, octal or hexadecimal). For version 1 of this design, the group has decided to limit the input to single-digit numbers for any of the inputs.
Using the above scenario design Truth Tables for the system and its various parts.
Chapter 7 Solutions
LogixPro PLC Lab Manual for Programmable Logic Controllers
Ch. 7 - Prob. 1RQCh. 7 - Prob. 2RQCh. 7 - Prob. 3RQCh. 7 - Prob. 4RQCh. 7 - a. What are the two methods commonly used to...Ch. 7 - Prob. 6RQCh. 7 - Prob. 7RQCh. 7 - Prob. 8RQCh. 7 - For a TOF timer: a. When is the enable bit of a...Ch. 7 - Explain what each of the following quantities...
Ch. 7 - State the method used to reset the accumulated...Ch. 7 - Study the ladder logic program in Figure 7-40 and...Ch. 7 - Study the ladder logic program in Figure 7-42, and...Ch. 7 - Prob. 6PCh. 7 - Prob. 7PCh. 7 - Prob. 8PCh. 7 - Prob. 9PCh. 7 - Prob. 10PCh. 7 - Prob. 11PCh. 7 - Prob. 13PCh. 7 - When the lights are turned off in a building, an...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- (Mechanics) The deflection at any point along the centerline of a cantilevered beam, such as the one used for a balcony (see Figure 5.15), when a load is distributed evenly along the beam is given by this formula: d=wx224EI(x2+6l24lx) d is the deflection at location x (ft). xisthedistancefromthesecuredend( ft).wistheweightplacedattheendofthebeam( lbs/ft).listhebeamlength( ft). Eisthemodulesofelasticity( lbs/f t 2 ).Iisthesecondmomentofinertia( f t 4 ). For the beam shown in Figure 5.15, the second moment of inertia is determined as follows: l=bh312 b is the beam’s base. h is the beam’s height. Using these formulas, write, compile, and run a C++ program that determines and displays a table of the deflection for a cantilevered pine beam at half-foot increments along its length, using the following data: w=200lbs/ftl=3ftE=187.2106lb/ft2b=.2fth=.3ftarrow_forwardWITH SCREENSHOT OF THE FLOWCODE PLEASE Make a program with 5 switches (SW0 – SW4) and an 8-bit LED array. When SW0 is pressed, the system will display prime numbers. When SW1 is pressed, the system will display composite numbers. When SW2 is pressed, the system that illustrates power operation. When SW3 is pressed, the system that illustrates divisibility operation. When SW4 is pressed, the system will display a running light from the outermost to the inner most then inner to outer LEDs. The MSB and LSB lights UP 1st then the succeeding LEDS going to the center follows. Only 2 LEDs lights UP at the same time. Use matrix for the SW4 operation. All operations are continuous until you choose another switch or another operation.arrow_forwardCreate a VBA program that computes for the Computes for the Areaand Perimeter of a Rhombus. The output will be displayed in a message box.arrow_forward
- please I need help with this code in ccs carrow_forwardWhat is the major advantage of using a for loop instead of a while loop? a. Unlike with a while loop, the execution of multiple statements can depend on the test condition. b. With a for loop, it is impossible to create an infinite loop. c. It is the only way to achieve an indefinite loop. d. The loop control variable is initialized, tested, and altered all in one place.arrow_forward: Practical questiod 1. Write a C program for Arduino thar controls a set of two traffic lights A & B at a crossmadk. Assume that: When the traffic lighus (A) are green or amber, the traffic lights (B) are red. • When the traffic lights (B) are green or amber, the raffic lights (A) are red. Green lights must stay on for 15 seconds, amber lights for 5 seconds and red lights for 20 seconds. 2. Sketch the circuit diagram to wire the Arduina to the two traffic lights. O COr cone COn cone O csea csas ca R/W? RIW /N RIN N bits TOVO Mode ТОР OCRO COne 2:0 Set bits HGO Under Fast PWM 00 Normal immediate 00 K11 Normal operation, ocer disconnected 001 Phase Correct PWM on TOP OXFF Normal operation, OCcBA disconnected, 01 011 Clear Timer n Compee match ICTO 010 OCROA immediate aFF Ocen reserved OCBA toggles on Compare match, 011 Fast PWM exFF 01 111 ocon reserved 100 Reserved Clear OCex on Compare Match, Set OCex at ex0. inon-inverting mode) 10 101 Phase Correct PWM OCROA on TOP exee 110 Reserved…arrow_forward
- 2arrow_forwardArduino Programming AssignmentThe left (red) LED will start flashing at approximately 1hz. The LED will continually flash untilany of the 4 pushbuttons are pressed. Then the main program will start. One of the four top LEDs (all but the red LED) will randomly be turned on. The LED will stayon until the corresponding push button is pressed. If the correct pushbutton is pressed the LEDwill turn off and start the same cycle. If the wrong pushbutton is pressed or approximately 2seconds have passed, display the lose sequence. The lose sequence is that all 4 LEDs will sequentially light up every second This will last until for 4 seconds, then go back to the start where the red LED is flashing waiting to start. This loop will last for 6 correct button pushes. If all 6 button presses are correct, then a winsequence is displayed. This will flash all of the 4 top LEDs at 2 hz for 4 seconds. Then startover and the red LED will start flashing to start.arrow_forwardThe C programming language supports left-shift and right-shift operators. This Arduino sketch tests both shift operators: void setup () { Serial.begin (9600); 1 void loop (0 I Serial.println ("Test shift operations byte a = 0xl; Serial.println (a, BIN); a = a > 2; // right shift Serial.print.In (a, BIN); delay (10000); ") ; 6 10 11 12 13 The AVR instruction set supports five shift operations: logical shift left, logical shift right, arithmetic shift right, rotate left, rotate right. 1sl 1sr asr rol rorarrow_forward
- After scattering a 0.80 nm x-ray photon from a free electron, it bounces back at 1.4 x106 m / s. Write the C ++ code that finds the Compton shift in the wavelength of the photon and the angle at which the photon scatters.arrow_forwardInstruction: Kindly refer to the photo below. (Note: C programming language should be used)arrow_forwardHow to write a code for a traffic light. There are 3 leds; green, yellow, and red, photoresistor and a button. The three lights should change like a normal traffic light uninterrupted until the button or photoresistor activates. basically when the photoresistor detects darkness the cylce should break and the yellow light should flash until photoresistor detects light, then the traffic light resumes repeating pattern. last for for the button, when pressed it should stop the cycle and turn it to red momentarily and then resume the cylcearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- C++ for Engineers and ScientistsComputer ScienceISBN:9781133187844Author:Bronson, Gary J.Publisher:Course Technology Ptr
C++ for Engineers and Scientists
Computer Science
ISBN:9781133187844
Author:Bronson, Gary J.
Publisher:Course Technology Ptr