Fundamentals of Physics, Volume 1, Chapter 1-20
10th Edition
ISBN: 9781118233764
Author: David Halliday
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
thumb_up100%
Chapter 7, Problem 2Q
Figure 7-16a shows two horizontal forces that act on a block that is sliding to the right across a frictionless floor. Figure 7-16b shows three plots of the block’s kinetic energy K versus time t. Which of the plots best corresponds to the following three situations: (a) F1 = F2, (b) F1> F2,
Figure 7-16 Question 2.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Fundamentals of Physics, Volume 1, Chapter 1-20
Ch. 7 - Rank the following velocities according to the...Ch. 7 - Figure 7-16a shows two horizontal forces that act...Ch. 7 - Is positive or negative work done by a constant...Ch. 7 - In three situations, a briefly applied horizontal...Ch. 7 - The graphs in Fig. 7-18 give the x component Fx of...Ch. 7 - Figure 7-19 gives the x component Fx of a force...Ch. 7 - In Fig. 7-20, a greased pig has a choice of three...Ch. 7 - Figure 7-21a shows four situations in which a...Ch. 7 - Spring A is stiffer than spring B kA kB. The...Ch. 7 - A glob of slime is launched or dropped from the...
Ch. 7 - In three situations, a single force acts on a...Ch. 7 - Figure 7-23 shows three arrangements of a block...Ch. 7 - SSM A proton mass m = 1.67 1027 kg is being...Ch. 7 - If a Saturn V rocket with an Apollo spacecraft...Ch. 7 - On August 10, 1972, a large meteorite skipped...Ch. 7 - An explosion at ground level leaves a crater with...Ch. 7 - A father racing his son has half the kinetic...Ch. 7 - A bead with mass 1.8 10-2 kg is moving along a...Ch. 7 - A 3.0 kg body is at rest on a frictionless...Ch. 7 - A ice block floating in a river is pushed through...Ch. 7 - The only force acting on a 2.0 kg canister that is...Ch. 7 - A coin slides over a frictionless plane and across...Ch. 7 - A 12.0 N force with a fixed orientation does work...Ch. 7 - A can of bolts and nuts is pushed 2.00 m along an...Ch. 7 - A luge and its rider, with a total mass of 85 kg,...Ch. 7 - 14 GO Figure 7-27 shows an overhead view of three...Ch. 7 - GO Figure 7-28 shows three forces applied to a...Ch. 7 - GO An 8.0 kg object is moving in the positive...Ch. 7 - SSM WWW A helicopter lifts a 72 kg astronaut 15 m...Ch. 7 - a In 1975 the roof of Montreals Velodrome, witha...Ch. 7 - GO In Fig. 7-30, a block of ice slides down a...Ch. 7 - A block is sent up a frictionless ramp along which...Ch. 7 - 21 SSM A cord is used to vertically lower an...Ch. 7 - A cave rescue team lifts an injured spelunker...Ch. 7 - In Fig. 7-32, a constant force Fa of magnitude...Ch. 7 - GO In Fig. 7-33, a horizontal force Fa of...Ch. 7 - GO In Fig. 7-34, a 0.250 kg block of cheese lies...Ch. 7 - In Fig. 7-10, we must apply a force of magnitude...Ch. 7 - A spring and block are in the arrangement of Fig....Ch. 7 - During spring semester at MIT, residents of the...Ch. 7 - In the arrangement of Fig. 7-10, we gradually pull...Ch. 7 - In Fig. 7-10a, a block of mass m lies on a...Ch. 7 - SSM WWW The only force acting on a 2.0 kg body as...Ch. 7 - Figure 7-37 gives spring force Fx versus position...Ch. 7 - GO The block in Fig. 7-10a lies on a horizontal...Ch. 7 - ILW A 10 kg brick moves along an xaxis. Its...Ch. 7 - SSM WWW The force on a particle is directed along...Ch. 7 - GO A 5.0 kg block moves in a straight line on a...Ch. 7 - GO Figure 7-40 gives the acceleration of a 2.00 kg...Ch. 7 - A 1.5 kg block is initially at rest on a...Ch. 7 - GO A force F= cx3.00x2iacts on a particle as the...Ch. 7 - A can of sardines is made to move along an xaxis...Ch. 7 - A single force acts on a 3.0 kg particle-like...Ch. 7 - GO Figure 7-41 shows a cord attached to a cart...Ch. 7 - SSM A force of 5.0 N acts on a 15 kg body...Ch. 7 - A skier is pulled by a towrope up a frictionless...Ch. 7 - SSM ILW A 100 kg block is pulled at a constant...Ch. 7 - The loaded cab of an elevator has a mass of 3.0 ...Ch. 7 - A machine carries a 4.0 kg package from an initial...Ch. 7 - A 0.30 kg ladle sliding on a horizontal...Ch. 7 - Prob. 49PCh. 7 - a At a certain instant, a particle-like object is...Ch. 7 - A force F= 3.00 N i 7.00 N j 7.00 N k acts on...Ch. 7 - A funny car accelerates from rest through a...Ch. 7 - Figure 7-42 shows a cold package of hot dogs...Ch. 7 - GO The only force acting on a 2.0 kg body as the...Ch. 7 - SSM A horse pulls a cart with a force of 40 lb at...Ch. 7 - An initially stationary 2.0 kg object accelerates...Ch. 7 - A 230 kg crate hangs from the end of a rope of...Ch. 7 - To pull a 50 kg crate across a horizontal...Ch. 7 - A force Fa is applied to a bead as the bead is...Ch. 7 - A frightened child is restrained by her mother as...Ch. 7 - How much work is done by a force F= 2x N i 3 N j,...Ch. 7 - A 250 g block is dropped onto a relaxed vertical...Ch. 7 - 63 SSM To push a 25.0 kg crate up a frictionless...Ch. 7 - Boxes are transported from one location to another...Ch. 7 - In Fig. 7-47, a cord runs around two massless,...Ch. 7 - If a car of mass 1200 kg is moving along a highway...Ch. 7 - SSM A spring with a pointer attached is hanging...Ch. 7 - An iceboat is at rest on a frictionless frozen...Ch. 7 - If a ski lift raises 100 passengers averaging 660...Ch. 7 - A force F= 4.0 N i cj acts on a particle as the...Ch. 7 - A constant force of magnitude 10 N makes an angle...Ch. 7 - In Fig. 7-49a, a 2.0 N force is applied to a 4.0...Ch. 7 - A force F in the positive direction of an x axis...Ch. 7 - A particle moves along a straight path through...Ch. 7 - SSM What is the power of the force required to...Ch. 7 - A 45 kg block of ice slides down a frictionless...Ch. 7 - As a particle moves along an x axis, a force in...Ch. 7 - A CD case slides along a floor in the positive...Ch. 7 - SSM A 2.0 kg lunchbox is sent sliding over a...Ch. 7 - Numerical integration. A breadbox is made to move...Ch. 7 - In the block-spring arrangement of Fig. 7-10, the...Ch. 7 - A 4.00 kg block is pulled up a frictionless...Ch. 7 - A spring with a spring constant of 18.0 N/cm has a...Ch. 7 - A force F= 2.00 i 9.00 j 5.30 k N acts on a 2.90...Ch. 7 - At t = 0, force F= 5.00 i 5.00 j 4.00 k N begins...
Additional Science Textbook Solutions
Find more solutions based on key concepts
What is the meaning of the Greek words from which we get the word thermo-dynamics?
Conceptual Physics: The High School Physics Program
15. Which requires more work: lifting a 50-kg sack a vertical distance of 2 m or lifting a 25-kg sack a vertica...
Conceptual Physical Science (6th Edition)
If two vectors are equal, what can you say about their components? What can you say about their magnitudes? Wha...
University Physics Volume 1
The value of the charge q3 for the net force on it to be 4.00 μΝ .
Sears And Zemansky's University Physics With Modern Physics
13. A 50 kg box hangs from rope. What is the tension in the rope if:
a. The box is at rest?
b. The box moves ...
Physics for Scientists and Engineers: A Strategic Approach, Vol. 1 (Chs 1-21) (4th Edition)
Find the work done by a force F = 1.8 + 2.2 N as it acts on an object moving from the origin to the point 56 ...
Essential University Physics: Volume 1 (3rd Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A block of mass m = 2.50 kg is pushed a distance d = 2.20 m along a frictionless, horizontal table by a constant applied force of magnitude F = 16.0 N directed at an angle = 25.0 below the horizontal as shown in Figure P6.3. Determine the work done on the block by (a) the applied force, (b) the normal force exerted by the table, (c) the gravitational force, and (d) the net force on the block. Figure P6.3arrow_forwardIf the net work done by external forces on a particle is zero, which of the following statements about the particle must be true? (a) Its velocity is zero. (b) Its velocity is decreased. (c) Its velocity is unchanged. (d) Its speed is unchanged. (e) More information is needed.arrow_forwardAs shown in Figure P7.20, a green bead of mass 25 g slides along a straight wire. The length of the wire from point to point is 0.600 m, and point is 0.200 in higher than point . A constant friction force of magnitude 0.025 0 N acts on the bead. (a) If the bead is released from rest at point , what is its speed at point ? (b) A red bead of mass 25 g slides along a curved wire, subject to a friction force with the same constant magnitude as that on the green bead. If the green and red beads are released simultaneously from rest at point , which bead reaches point first? Explain. Figure P7.20arrow_forward
- A boy starts at rest and slides down a frictionless slide as in Figure P5.64. The bottom of the track is a height h above the ground. The boy then leaves the track horizontally, striking the ground a distance d as shown. Using energy methods, determine the initial height H of the boy in terms of h and d. Figure P5.64arrow_forwardA block of mass 0.500 kg is pushed against a horizontal spring of negligible mass until the spring is compressed a distance x (Fig. P7.79). The force constant of the spring is 450 N/m. When it is released, the block travels along a frictionless, horizontal surface to point , the bottom of a vertical circular track of radius R = 1.00 m, and continues to move up the track. The blocks speed at the bottom of the track is = 12.0 m/s, and the block experiences an average friction force of 7.00 N while sliding up the track. (a) What is x? (b) If the block were to reach the top of the track, what would be its speed at that point? (c) Does the block actually reach the top of the track, or does it fall off before reaching the top?arrow_forwardConsider a particle on which a force acts that depends on the position of the particle. This force is given by . Find the work done by this force when the particle moves from the origin to a point 5 meters to the right on the x-axis.arrow_forward
- A particle moves in one dimension under the action of a conservative force. The potential energy of the system is given by the graph in Figure P8.55. Suppose the particle is given a total energy E, which is shown as a horizontal line on the graph. a. Sketch bar charts of the kinetic and potential energies at points x = 0, x = x1, and x = x2. b. At which location is the particle moving the fastest? c. What can be said about the speed of the particle at x = x3? FIGURE P8.55arrow_forwardAn object of mass m = 5.8 kg moves under the influence of one force. That force causes the object to move along a path given by x = 6.0 + 5.0t + 2.0t2, where x is in meters and t is in seconds. Calculate the work done by the force on the object from t = 2.0 s to t = 7.0 s.arrow_forwardRepeat the preceding problem, but this time, suppose that the work done by air resistance cannot be ignored. Let the work done by the air resistance when the skier goes from A to B along the given hilly path be —2000 J. The work done by air resistance is negative since the air resistance acts in the opposite direction to the displacement. Supposing the mass of the skier is 50 kg, what is the speed of the skier at point B ?arrow_forward
- A 4.00-kg particle moves from the origin to position ©, having coordinates x = 5.00 m and y = 5.00 m (Fig. P6.42). One force on the particle is the gravitational force acting in the negative y direction. Using Equation 6.3, calculate the work done by the gravitational force on the particle as it goes from O to © along (a) the purple path, (b) the red path, and (c) the blue path. (d) Your results should all be identical. Why? Figure P6.42 Problems 42 through 45.arrow_forwardFigure P9.65A shows a crate attached to a rope that is extended over an ideal pulley. Boris pulls on the other end of the rope with a constant force until the crate has risen a total distance of 6.53 m (Fig. P9.65B). If the crate has a mass of 81.36 kg, what is the average power exerted by Boris, assuming he accomplishes the task in 5.33 s? FIGURE P9.65arrow_forwardA particle moves in the xy plane (Fig. P9.30) from the origin to a point having coordinates x = 7.00 m and y = 4.00 m under the influence of a force given by F=3y2+x. a. What is the work done on the particle by the force F if it moves along path 1 (shown in red)? b. What is the work done on the particle by the force F if it moves along path 2 (shown in blue)? c. What is the work done on the particle by the force F if it moves along path 3 (shown in green)? d. Is the force F conservative or nonconservative? Explain. FIGURE P9.30 In each case, the work is found using the integral of Fdr along the path (Equation 9.21). W=rtrfFdr=rtrf(Fxdx+Fydy+Fzdz) (a) The work done along path 1, we first need to integrate along dr=dxi from (0,0) to (7,0) and then along dr=dyj from (7,0) to (7,4): W1=x=0;y=0x=7;y=0(3y2i+xj)(dxi)+x=7;y=0x=7;y=4(3y2i+xj)(dyj) Performing the dot products, we get W1=x=0;y=0x=7;y=03y2dx+x=7;y=0x=7;y=4xdy Along the first part of this path, y = 0 therefore the first integral equals zero. For the second integral, x is constant and can be pulled out of the integral, and we can evaluate dy. W1=0+x=7;y=0x=7;y=4xdy=xy|x=7;y=0x=7;y=4=28J (b) The work done along path 2 is along dr=dyj from (0,0) to (0,4) and then along dr=dxi from (0,4) to (7,4): W2=x=0;y=0x=0;y=4(3y2i+xj)(dyj)+x=0;y=4x=7;y=4(3y2i+xj)(dyi) Performing the dot product, we get: W2=x=0;y=0x=0;y=4xdy+x=0;y=4x=7;y=43y2dx Along the first part of this path, x = 0. Therefore, the first integral equals zero. For the second integral, y is constant and can be pulled out of the integral, and we can evaluate dx. W2=0+3y2x|x=0;y=4x=7;y=4=336J (c) To find the work along the third path, we first write the expression for the work integral. W=rtrfFdr=rtrf(Fxdx+Fydy+Fzdz)W=rtrf(3y2dx+xdy)(1) At first glance, this appears quite simple, but we cant integrate xdy=xy like we might have above because the value of x changes as we vary y (i.e., x is a function of y.) [In parts (a) and (b), on a straight horizontal or vertical line, only x or y changes]. One approach is to parameterize both x and y as a function of another variable, say t, and write each integral in terms of only x or y. Constraining dr to be along the desired line, we can relate dx and dy: tan=dydxdy=tandxanddx=dytan(2) Now, use equation (2) in (1) to express each integral in terms of only one variable. W=x=0;y=0x=7;y=43y2dx+x=0;y=0x=7;y=4xdyW=y=0y=43y2dytan+x=0x=7xtandx We can determine the tangent of the angle, which is constant (the angle is the angle of the line with respect to the horizontal). tan=4.007.00=0.570 Insert the value of the tangent and solve the integrals. W=30.570y33|y=0y=4+0.570x22|x=0x=7W=112+14=126J (d) Since the work done is not path-independent, this is non-conservative force. Figure P9.30ANSarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax College
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781938168000
Author:Paul Peter Urone, Roger Hinrichs
Publisher:OpenStax College
8.01x - Lect 11 - Work, Kinetic & Potential Energy, Gravitation, Conservative Forces; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=9gUdDM6LZGo;License: Standard YouTube License, CC-BY