PROGRAMMABLE LOGIC CONTROLLERS (LOOSE PA
5th Edition
ISBN: 9781264206216
Author: Petruzella
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 7, Problem 5P
Study the ladder logic
- a. What type of timer has been programmed?
- b. What is the length of the time-delay period?
- c. When does the timer start timing?
- d. When is the timer reset?
- e. When will rung 3 be true?
- f. When will rung 5 be true?
- g. When will output PL4 be energized?
- h. Assume that your accumulated time value is up to 020 and power to your system is lost. What will your accumulated time value be when power is restored?
- i. What happens if inputs PB1 and PB2 are both true at the same time?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
3. Study the ladder logic program in Figure 7-40 and answer the questions that follow:
a. What type of timer has been programmed?
b. What is the length of the time-delay period?
c. What is the value of the accumulated time when power is first applied?
d. When does the timer start timing?
e. When does the timer stop timing and reset itself?
f. When input LS1 is first closed, which rungs are true and which are false?
L1
Input
LS1
Ladder logic program
Outputs
L2
LS1
-TON
TIMER ON DELAY
Timer
T4:0
-(EN)-
Time base
1
Preset
10(DN)
SOL A-fo
Accumulated
°
SOL B-of
T4:0
SOL A
2
3
4
10
DN
T4:0
SOL B
DN
T4:0
R
EN
T4:0
EN
Figure 7-40 Ladder logic program for Problem 3.
R
Q2): Design a sequential circuit with two T flip-flops A and B, and one input x_in.
(a) When x_in = 0, the state of the circuit remains the same. Whenx_in = 1, the circuit goes through the
state transitions from 00 to 01, to 11, to 10, back to 00, and repeats.
(b) When x_in= 0, the state of the circuit remains the same. When x_in=1, the circuit goes through the
state transitions from 00 to 11, to 01, to 10, back to 00, and repeats.
2. Design a logic circuit that controls an elevator door in a three-story building. The circuit has four inputs.
M is a logic signal that indicates when an elevator is moving (M=1) or stopped (M=0). F1, F2 and F3
are floor indicator signals that are normally LOW, and they go HIGH only when the elevator is
positioned at the level of that particular floor. For example, when the elevator is lined up level with
the second floor, F2=1 and F1=F3=0. The circuit output is the OPEN signal which is normally LOW
and is to go HIGH when the elevator door is to be opened.
Chapter 7 Solutions
PROGRAMMABLE LOGIC CONTROLLERS (LOOSE PA
Ch. 7 - Prob. 1RQCh. 7 - Prob. 2RQCh. 7 - Prob. 3RQCh. 7 - Prob. 4RQCh. 7 - a. What are the two methods commonly used to...Ch. 7 - Prob. 6RQCh. 7 - Prob. 7RQCh. 7 - Prob. 8RQCh. 7 - For a TOF timer: a. When is the enable bit of a...Ch. 7 - Explain what each of the following quantities...
Ch. 7 - State the method used to reset the accumulated...Ch. 7 - Study the ladder logic program in Figure 7-40 and...Ch. 7 - Study the ladder logic program in Figure 7-42, and...Ch. 7 - Prob. 6PCh. 7 - Prob. 7PCh. 7 - Prob. 8PCh. 7 - Prob. 9PCh. 7 - Prob. 10PCh. 7 - Prob. 11PCh. 7 - Prob. 13PCh. 7 - When the lights are turned off in a building, an...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
The job of the _____ is to fetch instructions, carry out the operations commanded by the instructions, and prod...
Starting Out With Visual Basic (7th Edition)
The ____________ is always transparent.
Web Development and Design Foundations with HTML5 (8th Edition)
Porter’s competitive forces model: The model is used to provide a general view about the firms, the competitors...
Management Information Systems: Managing The Digital Firm (16th Edition)
What output will the following lines of code display on the screen? cout "The works of Wolfgang\ninclude the f...
Starting Out with C++: Early Objects
How does a computers main memory differ from its auxiliary memory?
Java: An Introduction to Problem Solving and Programming (7th Edition)
A byte is made up of eight a. CPUs b. addresses c. variables d. bits
Starting Out with Java: From Control Structures through Objects (7th Edition) (What's New in Computer Science)
Knowledge Booster
Similar questions
- Program Timer 0 to be an event counter. Use mode 2 and display the binary count on P2 continuously. Set the initial count to 20.arrow_forward3. Design a logic circuit that controls an elevator door in a three-story building. M is a logic signal that indicates when the elevator is moving (M = 1) or stopped (M = 0). F1, F2, and F3 are floor indicator signals that are normally LOW, and they go HIGH only when the elevator is positioned at the level of that particular floor. For example, when the elevator is lined up level with the second floor, F2 = 1 and F1 = F3 = 0. The circuit output is the OPEN signal, which is normally LOW and will go HIGH when the elevator door is to be opened. We can fill in the truth table for the OPEN output as follows: a. Because the elevator cannot be lined up with more than one floor at a time, only one of the floor inputs can be HIGH at any given time. This means that all those cases in the truth table where more than one floor input is a 1 are don't-care conditions. We can place an x in the OPEN output column for those eight cases where more than one F input is 1. b. Looking at the other eight…arrow_forwardWrite a program in Python representing 7 logic gates: AND NAND OR NOR XOR XNOR NOT Accept (only) two inputs to create all outputs. Use the if statement to perform the Boolean logic. Only accept numeric input. If a number is greater than 0 treat it as a 1. Specify in your output and in the beginning of the code (through print statements) which gate the code represents. Comment the code.arrow_forward
- A programmer needs to design a delay using the attached snippet of code. If the Clock frequency supported from oscillator is 1 MHz then after executing this code how long will be the period of this delay.(Note that the previous value of counter1 is D'250') dell nop 31 суcle ;1 cycle 2 cycle decfsz counter1,f goto dell Select one: O a. 4 sec b. None of the answers.- C. 5 msec O d. 4 msec О е.4 useсarrow_forwardDevelop a python program to create clock-controlled latches. Your program should have the following sequence to test the circuit operation, as follows: describe how you were able to make it and how come this code was successful. Thanks a million!arrow_forwardIf the value of the damping ratio or damping factor is 0.5, then the system is an underdamped system. Select one: O True O Falsearrow_forward
- 3-Write the truth table and logic equation represented by this circuit? te A XOR OR AND XOR 4-Draw the logic circuit represented the following truth table. INPUT A INPUT B INPUT C OUTPUT P 0. 1. 1. 01 1arrow_forward2. Design a logic circuit with two inputs and 4 outputs, with each of the outputs hooked up to an LED. Only the first LED should light up when the input values are 00. Only the next LED should light up with the input values are 01. Only the following LED should light up for 10, and only the last LED should light up for input 11. Thus for each input combination, you should have one LED only being lit. This is called a DECODER circuit, you are decoding 2 bit binary input to one of 4 discrete outputs. a. Create the truth table (use the standard truth table format). b. Write a Boolean expression that corresponds to the truth table.arrow_forwardWrite the word TRUE if the statement is correct If the statement is false, replace the word's that, if substituted for the underlined word/s, would make the statement correct. Flip-flops are asynchronous bi-stable devices because there can only be two states. Negative edged triggered flip-flop has a bubble on the clock input signal which means that the circuit will only respond to negative The S-R flip-flop is a single-input version of the J-K flip-flop formed by tying both inputs togetherarrow_forward
- Cars have a brake light located at the center of the rear window. Write a program to flush the break light ON and OFF and for 5 times (ON for 1 second then OFF for another 1 second) when the driver presses the brake pedal. The brake pedal is connected to Po of input port 00H, and the brake light is connected to the P7 of output port 01H. (a) Design necessary circuit of the system. (b) Write necessary program to run the system.arrow_forwardTask 5: Logic circuits with multiple outputs Find the Boolean expression of the outputs of the following circuit, D = E = Draw the circuit on EWB and simulate it to fill-in its truth table shown below (use logic converter please). Note: You need to use the logic converter two times, once for the output D, and another time for the second output E.arrow_forwardAnswer the given question with a proper explanation and step-by-step solution. Programming the Pico micropython Write a code with helper functions that makes 4 sounds with 250 Hz, 500 Hz, 750 Hz, and 1000 Hz of PWM frequency by the Cytron board’s Buzzer (connected to GP18), respectively, every 1 sec (each sound lasts 0.25 sec) if you press and hold GP20 button. Also, the code should play the same 4 notes in a reverse sequence from highest to lowest frequencies every 1 sec (each sound lasts 0.25 sec) when the GP22 button is pressed. In addition to that, your code should turn on the LED of GP2 while making 250 Hz sound, the LED of GP3 while making 500 Hz sound, the LED of GP4 while making 750 Hz sound, and the LED of GP5 while making 1000 Hz sound. Moreover, nothing should happen if you press both GP20 and GP22 buttons at the same time. You SHOULD define helper functions to be called for making each sound and turning its corresponding LED on. You may need another function to be defined…arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Database System ConceptsComputer ScienceISBN:9780078022159Author:Abraham Silberschatz Professor, Henry F. Korth, S. SudarshanPublisher:McGraw-Hill EducationStarting Out with Python (4th Edition)Computer ScienceISBN:9780134444321Author:Tony GaddisPublisher:PEARSONDigital Fundamentals (11th Edition)Computer ScienceISBN:9780132737968Author:Thomas L. FloydPublisher:PEARSON
- C How to Program (8th Edition)Computer ScienceISBN:9780133976892Author:Paul J. Deitel, Harvey DeitelPublisher:PEARSONDatabase Systems: Design, Implementation, & Manag...Computer ScienceISBN:9781337627900Author:Carlos Coronel, Steven MorrisPublisher:Cengage LearningProgrammable Logic ControllersComputer ScienceISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Database System Concepts
Computer Science
ISBN:9780078022159
Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan
Publisher:McGraw-Hill Education
Starting Out with Python (4th Edition)
Computer Science
ISBN:9780134444321
Author:Tony Gaddis
Publisher:PEARSON
Digital Fundamentals (11th Edition)
Computer Science
ISBN:9780132737968
Author:Thomas L. Floyd
Publisher:PEARSON
C How to Program (8th Edition)
Computer Science
ISBN:9780133976892
Author:Paul J. Deitel, Harvey Deitel
Publisher:PEARSON
Database Systems: Design, Implementation, & Manag...
Computer Science
ISBN:9781337627900
Author:Carlos Coronel, Steven Morris
Publisher:Cengage Learning
Programmable Logic Controllers
Computer Science
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education