Steel Design (Activate Learning with these NEW titles from Engineering!)
6th Edition
ISBN: 9781337094740
Author: Segui, William T.
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 7, Problem 7.6.3P
To determine
(a)
The total number of A307 bolts.
To determine
(b)
The total number of group A bolts.
To determine
(c)
The total number of group B bolts.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Design a framed beam connection for a W18 x 50 to support a dead load reaction of 30 k and a live load reaction of 20 k, using the LRFD and ASD methods.The beam’s top flange is to be coped for a 2-in depth, and 7/8-in A325-X bolts in standard-size holes are to be used.The beam is connected to a W27 x 146 girder. Connection is A36,while W shapes are A992
Use load and resistance factor design and select a W shape with a nominal depth of 10 inches (a W10) to resist a dead load of 175 kips and a live load of 175 kips. The connection will be through the flanges with two lines of 1 1/4–inch-diameter bolts in each flange, as shown. Each line contains more than two bolts. The length of the member is 30 feet. Use A242 steel.
The billboard post support a 5KN dead load as shown. The cantilever beam and the brace is pinnedconnected to the post. Assume that the connections along the cap and the cap plate is adequate, as well asthe gusset plate and the cap plate. Use LRFD design considerations.a.) Determine the ultimate tensile force the brace carries. b.) Determine the adequacy of Connection 1 the bolt where 2- 16mm Ø A325 hex bolt and the plateswhere A36 steel. c.) If the connection at Connection 1 will be a welded connection what will be the adequate thickness ofthe weld. Note that the welds are only applied at the sides of the cap plate. Use electrode 70 for theweld. d.) Determine the adequacy of the connection due to shear and tension in Connection 2 if the bolts were4- 12mm Ø A325 hex bolt.
Chapter 7 Solutions
Steel Design (Activate Learning with these NEW titles from Engineering!)
Ch. 7 - Prob. 7.3.1PCh. 7 - Prob. 7.3.2PCh. 7 - Prob. 7.4.1PCh. 7 - Prob. 7.4.2PCh. 7 - Prob. 7.4.3PCh. 7 - Prob. 7.4.4PCh. 7 - Prob. 7.4.5PCh. 7 - Prob. 7.4.6PCh. 7 - Prob. 7.6.1PCh. 7 - Prob. 7.6.2P
Ch. 7 - Prob. 7.6.3PCh. 7 - Prob. 7.6.4PCh. 7 - Prob. 7.6.5PCh. 7 - Prob. 7.6.6PCh. 7 - Prob. 7.7.1PCh. 7 - Prob. 7.7.2PCh. 7 - Prob. 7.7.3PCh. 7 - Prob. 7.8.1PCh. 7 - Determine the adequacy of the hanger connection in...Ch. 7 - Prob. 7.9.1PCh. 7 - Prob. 7.9.2PCh. 7 - Prob. 7.9.3PCh. 7 - Prob. 7.9.4PCh. 7 - Prob. 7.9.5PCh. 7 - Prob. 7.11.1PCh. 7 - Prob. 7.11.2PCh. 7 - Prob. 7.11.3PCh. 7 - Prob. 7.11.4PCh. 7 - Prob. 7.11.5PCh. 7 - Prob. 7.11.6PCh. 7 - Prob. 7.11.7PCh. 7 - Prob. 7.11.8PCh. 7 - Prob. 7.11.9PCh. 7 - Prob. 7.11.10P
Knowledge Booster
Similar questions
- Select an American Standard Channel shape for the following tensile loads: dead load = 54 kips, live load = 80 kips, and wind load = 75 kips. The connection will be with longitudinal welds. Use an estimated shear lag factor of U = 0.85. (In a practical design, once the member was selected and the connection designed, the value of U would be computed and the member design could be revised if necessary.) The length is 17.5 ft. Use Fy=50 ksi and Fu=65 ksi. a. Use LRFD. b. Use ASD.arrow_forwardUse load and resistance factor design and select a W shape with a nominal depth of 10 inches (a W 10) to resist a dead load of 175 kips and a live load of 175 kips. The connection will be through the flanges with two lines of 11 4 -inch-diameter bolts in each flange, as shown in Figure P3.6-6. Each line contains more than two bolts. The length of the member is 30 feet. Use A588 steal.arrow_forwardA tension member with a length of 6 feet must resist a service dead load of 22 kips and a service live load of 55 kips. Select a member with a rectangular cross section. Use A36 steel and assume a connection with one line of 7/8-inch-diameter bolts. Use load combination Pu = 1.2D + 1.6L for LRFD.arrow_forward
- A plate 3⁄8 3 6 is used as a tension member to resist a service dead load of 12 kips and a service live load of 33 kips. This member will be connected to a 3⁄8-inch gusset plate with 3⁄4-inch-diameter Group A bolts. A36 steel is used for both the tension member and the gusset plate. Assume that the bearing strength is adequate, and determine the number of bolts required based on bolt shear.arrow_forwardThe three-plate moment connection shown below are all shop− welded· to the column and then field bolted to the girder. The beam is a W18 55 that has a factored moment of Mu = 382 kip ft and a factored shear of Vu = 65 kip. All plates are A36 steel (Fy = 36 ksi, Fu = 58 ksi). Plate 2 is connected to the girder using four bolts as shown. All bolts for the connection are 7/8” diameter A325-X. Design Plate 1, including the required number of bolts and dimensions of the plate. Assume an E70XX weld to the column. Consider limit states only for the plate itself. That is, you do not need to consider limit states for the beam or column. For which plate(s) will you need to check the buckling capacity, Plate 1, 2, and/or 3? Explain.arrow_forwardFor following tensioned loads PD=80kips and PL=120kips and by using LRFD method, select the lightest WT6 channel shape to be used as a 20ft long. The member will be connected by a longitudinal weld to flange only (6in) in long at the end. Use A992 Grade (Fy= 50ksi and Fu=65ksi)arrow_forward
- The bracket connection shown in Figure must support an eccentric load consisting of 9 kips of dead load and 27 kips of live load. The connection was designed to have two vertical rows of four bolts, but one bolt was inadvertently omitted. If 7⁄8inchdiameter Group A bearingtype bolts are used, is the connection adequate? Assume that the bolt threads are in the plane of shear. Use A36 steel for the bracket, A992 steel for the W6 x 25, and perform the following analyses: (a) elastic analysis, (b) ultimate strength analysis.arrow_forwardDetermine the maximum service load that can be applied if the live loadto-dead load ratio is 2.5. Investigate all limit states. The tension member is of A572 Grade 50 steel, and the gusset plate is A36. The weld is a 3⁄16-inch fillet weld with E70 electrodes. a. Use LRFD. b. Use ASD.arrow_forwardA beam is connected to a column with 7/8-inch-diameter, A325N bearing-type bolts, as shown in the figure. Eight bolts connect the tee to the column. A992 steel is used. Is the tee to column connection adequate? Use LRFD. You do not need to check the tee to beam connection. Don’t forget to include the combined shear and tension stresses on the eight bolts due to the eccentricity of the connection. Next, assume that this connection was to be made into a moment connection by bringing the flanges of the beam tight to the column flange, then providing fillet welds (E70) on both sides of each beam flange to the column flange. Ignore the small length that the web of the beam is in the way and thus prevents a full fillet weld on the one side of each flange. Using the maximum fillet weld size recommended, can a moment connection be made that is adequate if it is required to resist 75% of the φMp capacity of the beam? Do not worry about checking the shear connection with the WT again and…arrow_forward
- Prepare the Bar bending schedule of a simply supported R.C.C. Lintels from the following specification: Size of lintel 300mm widex 200mm depth. Main bars in tension zone of Fe 250(grade I) 3 bars of 16mm dia., one bar is cranked through 45 degree at 170 mm from each end 2 No. anchor bars at top 8mm dia. Two legged stirrups@150mm c/c of 6mm dia. through out. Clear span of the lintel is 1150mm. Bearing on either side is 150mmarrow_forwardA WT10.5 x 31 is used as a bracket to transmit a 60-kip service load to a W14 x 90 column, as previously shown in Figure . The load consists of 15 kips dead load and 45 kips live load. Four 7⁄8-inch-diameter Group A bolts are used. The column is of A992 steel, and the bracket is A36. Assume all spacing and edge-distance requirements are satisfied, including those necessary for the use of the nominal strength in bearing deformation (i.e., 2.4dtFu)*, and determine the adequacy of the bolts for the following types of connections: (a) bearing-type connection with the threads in shear and (b) slip-critical connection with the threads in shear.arrow_forwardA C12 × 30 is connected with 1-in. diameter bolts in each flange, as shown in Figure P3.2-3. If Fy = 50 ksi, Fu = 65 ksi, and Ae = 0.90An, compute the following. a. The design strength for LRFD. b. The allowable strength for ASD.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning