LogixPro PLC Lab Manual for Programmable Logic Controllers
5th Edition
ISBN: 9781259680847
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Question
Chapter 8, Problem 11RQ
Program Plan Intro
a.
Programmable Logic Controller (PLC):
- Programmable Logic Controller (PLC) is a specialized computer used in industrial segments to control machines and process.
- PLC is program that consists of a set of instructions which resembles the controlling functions needed to perform specific tasks.
- The function of PLC is similar to that of a relay and hence, in an industrial segment a relay is greatly replaced by a suitable PLC.
- When compared to general Personal Computer (PC), a PLC is available in small and tiny sizes.
- The basic architecture of a PLC consists of an input-output interface module and a small Central Processing Unit (CPU) that runs by control
programming language.
PLC counter:
- A counter is a PLC instruction which counts up or down when the input transfers from an off state (false) to an on state (true).
- The three different types of counters instructions are as follows:
- Up counter
- Down counter
- Combined counter
Explanation of Solution
b.
Underflow bit of a down-counter:
- An underflow occurs when the count value goes below its preset value...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Assume that you have two-bit arithmetic circuit as below. To get output D = A - B, what are S1, S0 and Cin , respectively?
Synchronization bit at the beginning of character is called start bit explain?
1. If the number 3 is to be printed on the common cathode 7 segment display, which of the following should be the a-b-c-d-e-f-g inputs?
Chapter 8 Solutions
LogixPro PLC Lab Manual for Programmable Logic Controllers
Ch. 8 - Name the three forms of PLC counter instructions,...Ch. 8 - State four pieces of information usually...Ch. 8 - In a PLC counter instruction, what rule applies to...Ch. 8 - Prob. 4RQCh. 8 - When does the PLC counter instruction increment or...Ch. 8 - Prob. 6RQCh. 8 - Prob. 7RQCh. 8 - Prob. 8RQCh. 8 - Prob. 9RQCh. 8 - Prob. 10RQ
Knowledge Booster
Similar questions
- Learn to tell the difference between serial and parallel code.arrow_forwardIf 2 bits of a byte are in error when the byte is read from ECC memory, can ECC detect the error? Can it fix the error?arrow_forwardTHINKING CRITICALLY If 2 bits of a byte are in error when the byte is read from ECC memory, can ECC detect the error? Can it fix the error?arrow_forward
- Assume SP is 256, LOCAL is 300, ARGUMENT is 400, THIS is 3000, and THAT is 3010. Translate the following VM code into ASM code: push constant 7 push constant 3 addarrow_forwardWhich interrupt (16h or 21h) is the best for reading user input with function keys and other extended keys?arrow_forwardGiven a bit array A = [ 0 0 1 1 0 1] on which the operations are workable:i) Can you use OR to change any desired bit of A to 1?ii) Can you use AND to change any desired bit of A to 0?iii) Can you use XOR to invert or toggle any desired bit of A?arrow_forward
- Which instruction shifts each bit to the right, copies the lowest bit into the Carry flag, andcopies the Carry flag into the highest bit position?arrow_forwardThe carry register: A. Is set when a carry from bit 7 occurs.B. Is set when a "borrow" for bit 7 of the accumulator occurs.C. Acts like the ninth bit of the accumulator.D. All the above.arrow_forwardWhat are the two modes of synchronization? Write the format of the modes.arrow_forward
- please use python language, show in your code that you can read a value from Force Resistant Pad, then open actuator 1 and close actuator 1 and when lid shuts read that value again if it is less than 50 open actuator 2 and ehen fsr pad regains the 50 value shut actuator 2? this is using a raspberry pi system, show pin output and input and output numbers, 8 bit analog to digital reader, FSR predetermined value is 500, also it is using a l298n motor driver.arrow_forwardHowmany bits in the control word of 8253 PIT? draw its bits and explain briefly the operation of each one.arrow_forwardWhich instruction copies the highest bit into both the Carry flag and the lowest bit position while shifting each bit in an operand to the left?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Comptia A+ Core 1 Exam: Guide To Computing Infras...Computer ScienceISBN:9780357108376Author:Jean Andrews, Joy Dark, Jill WestPublisher:Cengage Learning
A+ Guide To It Technical SupportComputer ScienceISBN:9780357108291Author:ANDREWS, Jean.Publisher:Cengage,
A+ Guide to Hardware (Standalone Book) (MindTap C...Computer ScienceISBN:9781305266452Author:Jean AndrewsPublisher:Cengage Learning
Comptia A+ Core 1 Exam: Guide To Computing Infras...
Computer Science
ISBN:9780357108376
Author:Jean Andrews, Joy Dark, Jill West
Publisher:Cengage Learning
A+ Guide To It Technical Support
Computer Science
ISBN:9780357108291
Author:ANDREWS, Jean.
Publisher:Cengage,
A+ Guide to Hardware (Standalone Book) (MindTap C...
Computer Science
ISBN:9781305266452
Author:Jean Andrews
Publisher:Cengage Learning