Thinking Like an Engineer: An Active Learning Approach (4th Edition)
4th Edition
ISBN: 9780134639673
Author: Elizabeth A. Stephan, David R. Bowman, William J. Park, Benjamin L. Sill, Matthew W. Ohland
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 9, Problem 11RQ
- 11. When a fluid flows slowly across a flat plate and transfers heat to the plate, the following variables are important. Analyze this system using Rayleigh’s method.
| ρ = Liquid density | [=] kg/m3 |
| Cp = Specific heat of liquid | [=] J/(g oC) |
| µ = Liquid viscosity | [=] kg/(m s) |
| k = Thermal conductivity of the plate | [=] W/(m oC) |
| h = Heat transfer coefficient | [=] W/(m2 °C) |
| x = Distance from edge of the plate | [=] m |
| v = Liquid velocity | [=] m/s |
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
If the given Pi is 3.14159
Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg
Liquid sample: density = 4 ml; time of flow = 4.5 seconds
What is the pressure in MKS unit and CGS unit?
What is its viscosity?
If the weight is 8.5 g, what is its density?
What is its kinematic viscosity?
What is its fluidity?
Important variables in a particular water machine are: Fluid density (ρ), impeller angular velocity (ω), impeller diameter (D), volume flow rate (), fluid viscosity (µ), head (gH). In fact, (gH) shows the energy that the fluid unit mass receives from or gives to the machine, independent of gravitational acceleration (g). Therefore, gH value is used instead of H. Important sizes in terms of the operation of the water machine are power (P), (gH) and efficiency ( h). Derive dimensionless numbers by typing these two parameters based on the above variables and applying Buckingham's p method (repeating variables method).
The Reynolds number is a dimensionless group defined as follows for a liquid that flows through a pipe:
Re = Dvρ / μ
where D is the diameter of the pipe, v is the velocity of the fluid, ρ is its density and µ its viscosity.
When the Reynolds number value is less than 2100, the flow is laminar, that is, the liquid it moves in lines of smooth flow. For Reynolds numbers greater than 2100, the flow is turbulent, characterized by considerable agitation. Liquid Methyl Ethyl Ketone (MEK) flows through 2067 '' ID tubing and through an average velocity of 0.48 ft / s. If the fluid temperature is 20 ° C, the density of the MEK The liquid is 0.805 g / cm and the viscosity is 0.43 cP (1 cP = 1.00 x 10 kg / (m-s)]. Determine the Reynolds number for MEK flow conditions. (Round the final result to a whole number without decimals).
Chapter 9 Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Ch. 9.1 - The heat loss (Q/t, in units of joules per second...Ch. 9.2 - A simple expression for the velocity of molecules...Ch. 9.2 - What are the dimensions of the value 6 in the...Ch. 9.4 - The Euler number is a function of the pressure...Ch. 9 - Complete the following table. Dimensions ...Ch. 9 - Complete the following table. Dimensions ...Ch. 9 - Calculate the numerical value of each of the...Ch. 9 - Calculate the numerical value of each of the...Ch. 9 - A fluid with a specific gravity of 0.91 and a...Ch. 9 - Brine, with a density of 1.25 grams per cubic...
Ch. 9 - When a simple turbine is used for mixing, the...Ch. 9 - History suggests that Newton developed his idea...Ch. 9 - It is proposed to create a set of dimensionless...Ch. 9 - 1. While researching fluid dynamics, you come...Ch. 9 - 2. While researching fluid dynamics, you came...Ch. 9 - 3. While researching fluid dynamics, you come...Ch. 9 - 4. The Arrhenius number (Ar) is the dimensionless...Ch. 9 - 5. The Biot number (Bi) is the dimensionless...Ch. 9 - 6. A biodegradable fuel having a specific gravity...Ch. 9 - 7. A sludge mixture having a specific gravity of...Ch. 9 - 8. Water (specific gravity = 1.02; viscosity =...Ch. 9 - 9. We have been asked to determine a set of...Ch. 9 - 10. The Peclet number is used in heat transfer in...Ch. 9 - 11. When a fluid flows slowly across a flat plate...Ch. 9 - 12. In modeling the flow of liquid in a piping...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the velocity of block D if end A of the rope is pulled down with a speed of vA = 3 m/s.
Engineering Mechanics: Dynamics (14th Edition)
Compute the hydraulic radius for a circular drain pipe running half full if its inside diameter is 300 mm.
Applied Fluid Mechanics (7th Edition)
The solid steel shaft AC has a diameter of 25 mm and is supported by smooth bearings at D and E. It is coupled ...
Mechanics of Materials
The moment of inertia Iy for the slender rod in terms of the rod’s total mass m .
Engineering Mechanics: Statics & Dynamics (14th Edition)
Steady state conduction rate to the warm compressor to the net power produces theoretically by thermodynamic ba...
Introduction to Heat Transfer
What is the importance of modeling in engineering? How are the mathematical models for engineering processes pr...
Heat and Mass Transfer: Fundamentals and Applications
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Consider the following equation. All three of the terms in parentheses are dimensionless groups. Because kC is difficult to determine directly, the other variables are measured and kC is calculated from the given equation. What is the estimated value of kC? What are the units of kC? Show your work. The following values were measured: D = 8.0 mm, DAB = 0.475 cm2/s, μ = 1.12 x 10–3 N-s/m2, ρ = 1.00 x 10–3 g/cm3, v = 15.0 m/s. Note: Given Equation attached belowarrow_forwardIn the United States, electricity is sold using the SI units of kilowatt (kW) or megawatt (MW), and fuel for power generation stations is generally purchased using English units, e.g., British thermal unit (Btu), gallon (gal), and ton. An industrial power plant has an average annual load of 100 MW (electrical). If the overall thermal efficiency is 33% (based on HHV), what is the annual cost of fuel if the plant is fired with (a) natural gas, (b) No. 2 fuel oil, and (c) bituminous coal? Use the data from Tables 2.2, 2.7, and 2.13. Assume the cost of natural gas is $5/million Btu, the cost of No. 2 fuel oil is $3/gal, and the cost of bituminous coal is $60/ton (1 ton = 2000 lbm)arrow_forwardThe pressure drop per unit length in horizontal pipe flow,∆ p/L , depends on the fluid density ρ , viscosity μ , diameterD , and volume flow rate Q . Rewrite this function in termsof pi groups.arrow_forward
- Fluid mechanics theory The power input P to a centrifugal pump is a function of the volume flow Q, impeller diameter D, rotational rate ω, and the density ρ and viscosity μ of the fluid. Determine the three dimensionless numbers. Use M, L, T as your primary dimensions and ω, ρ and D as repeatingvariables.arrow_forwardAt any time, approximately 20 volcanoes are actively erupting on the Earth, and 50–70 volcanoes erupt each year. Over the past 100 years, an average of 850 people have died each year from volcano eruptions. As scientists and engineers study the mechanics of lava flow, accurately predicting the flow rate (velocity) of the lava is critical to saving lives after an eruption. Jeffrey’s equation captures the relationship between flow rate and viscosity as: where ρ is the density of the lava, g is gravity, t is the flow thickness, α is the slope, and m is the lava viscosity. Typical values are given as follows for the flow rate: m= 4x103 kg/(m.s) ±1% ρ= 2.5 g/cm3 ±1% t= 28 cm ±0.5 cm α= 10° ±1 ° g= 9.81 m/s²arrow_forwardThe power P required to drive a propeller is known to depend on the diameter of the propeller D, the density of fluid ρ, the speed of sound a, the angular velocity of the propeller ω, the freestream velocity V , and the viscosity of the fluid µ. (a) How many dimensionless groups characterize this problem? (b) If the effects of viscosity are neglected, and if the speed of sound is not an important variable, express the relationship between power and the other variables in nondimensional form. (c) A one-half scale model of a propeller is built, and it uses Pm horsepower when running at a speed ωm. If the full-scale propeller in the same fluid runs at ωm/2, what is its power consumption in terms of Pm if the functional dependence found in part (b) holds? What freestream velocity should be used for the model test?arrow_forward
- Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Determine (a) pressure in MKS unit, (b) pressure in CGS unit, (c) the viscosity of the liquid, (d) If the weight was given as 8.5 grams, what will be the density of the liquid? (e) the kinematic viscosity of the liquid? (f) and the fluidity of the liquid?arrow_forwardMeasurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is:arrow_forwardA liquid of density ? and viscosity ? flows by gravity through a hole of diameter d in the bottom of a tank of diameter DFig. . At the start of the experiment, the liquid surface is at height h above the bottom of the tank, as sketched. The liquid exits the tank as a jet with average velocity V straight down as also sketched. Using dimensional analysis, generate a dimensionless relationship for V as a function of the other parameters in the problem. Identify any established nondimensional parameters that appear in your result. (Hint: There are three length scales in this problem. For consistency, choose h as your length scale.) except for a different dependent parameter, namely, the time required to empty the tank tempty. Generate a dimensionless relationship for tempty as a function of the following independent parameters: hole diameter d, tank diameter D, density ? , viscosity ? , initial liquid surface height h, and gravitational acceleration g.arrow_forward
- Suppose you're converting a bill of materials for machining feedstock from the British gravitational (U.S. system) of units to International System (SI) units. Your goal is to have all of the material quantities in kilograms. Your bill of materials lists values for required weights of brass rod in pounds. To convert to these values to kilograms you first you divide by gravitational acceleration in feet per second squared to get a mass in slugs, then convert slugs to kilograms using standard conversion factors. Group of answer choices True Falsearrow_forwardThe differential change in pressure p close to the surface of a static fluid is given by the following expression:dp/dy = -3Ap2,where A is a constant, with units of 1/(atm•m), and p is the pressure in atm. The pressure at the surface of the fluid is p(0) = 1 atm, and the coordinate y here is positive upwards with origin at the surface. An absulute pressure gauge is placed at a depth 0.19m in the fluid. What would be the reading of the pressure gauge in units in atm? you can take the constant A=1(atm.m)^-1arrow_forwardIn the field of air pollution control, one often needs to sample the quality of a moving airstream. In such measurements a sampling probe is aligned with the flow as sketched in Fig. A suction pump draws air through the probe at volume flow rate V· as sketched. For accurate sampling, the air speed through the probe should be the same as that of the airstream (isokinetic sampling). However, if the applied suction is too large, as sketched in Fig, the air speed through the probe is greater than that of the airstream (super iso kinetic sampling). For simplicity consider a two-dimensional case in which the sampling probe height is h = 4.58 mm and its width is W = 39.5 mm. The values of the stream function corresponding to the lower and upper dividing streamlines are ?l = 0.093 m2/s and ?u = 0.150 m2/s, respectively. Calculate the volume flow rate through the probe (in units of m3/s) and the average speed of the air sucked through the probe.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY