Package: Programmable Logic Controllers with Activities Manual
5th Edition
ISBN: 9781259717550
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 9, Problem 13RQ
Program Plan Intro
Pushbutton:
- It refers to a normal switch process that is used to control some aspects of machine or process.
- Pushbuttons are normally built of hard materials such as plastic or metal.
- Pushbuttons are normally used in calculators, kitchen appliances, and various other
mechanical and electronic devices.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A pushbutton can be used to send ____ to the uno. The pin to which the push button is connected must be configured as an ____.
Fill in the blank please
A pushbutton can be used to send ___ to the uno. The pin to which the pushbutton is connected must be configured as an ____.
Would it be current and pinMode function?
Would it be signal for the first one? Please help
Define StatusStrip control
Chapter 9 Solutions
Package: Programmable Logic Controllers with Activities Manual
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- An input device that uses switch contacts placed under a plastic pad which may be inscribed with symbols is known as Touch pad why?arrow_forwardThe EAM device that does not use a control panel is the:sorter why?arrow_forwardProgram using NXT or EV3 Activate the servo motor to drive the vehicle forward for 10 SEC Turn right 90° and move forward for 10 SEC, Turn Right 90° and move forward for 10 SEC Turn right 90° and move forward for 10 SECarrow_forward
- Traffic light control sequence flowchart A typical traffic light control sequence for a 4 road junction has been described below (for a road system where the vehicles keep to their left while driving i.e. Australia, UK, South Africa etc). The light changes as per the sequence listed below: A. Before switch ON, all 4 roads should get ‘flashing yellow’ so as to enable them to look around and cross the road junction. B. When switched ON, Main roads 1 & 3 should get green signals G1/G3 to go straight. This signal remains on for 30 seconds. C. The above signals should be changed over to go right GR1/GR3 for 15 seconds only if any sensor S1/S3 of vehicles waiting to turn right is detected in the right turn lane . This will take place after a brief yellow signals Y1/Y3 in between. D. In case no vehicle is waiting for right turn, the roads 1 & 3 should be closed with red signals R1/R3 and interim yellow signals Y1/Y3 for 2 seconds. E. The above…arrow_forwardVGA mode is used to show visual output on a monitor. What makes you think that way?arrow_forwardIt asks to use a system that reads an IR keyboard, and if pressed:button 1 turns on a spotlight and sends the message to an LCD: Garage spotlight onbutton 2 turns off the light and sends a message to an LCD: garage light offbutton 3 activates an ultrasonic sensor and if it detects something within 1 meter, it activates a buzzer and a message onLCD screen: intruder detected.And if the alarm is activated it can only be stopped with the red button of the IR keyboard. The circuit is shown belowarrow_forward
- Q/ Controlling the ON/OFF of two LEDs by using Push Button. Assumptions: 1. Push Button connected to PIN3 2. LEDI connected to PIN6 3. LED2 connected to PIN8 4. When the button is pushed, each time one of the two LEDs are ON, and other is OFF 5. When the button is pushed again, the state is reverse on the two LEDsarrow_forwardWhat causes the computer's fan to generate such a loud noise when it is charging or in use is unclear.arrow_forwardTo display visual data on a monitor, VGA mode is employed. What gives you the impression that's the case?arrow_forward
- How to install prompt module using npm install prompt-sync to enable user input on Notepad++?arrow_forwardThe lights in a classroom are controlled by two switches: one at the back and one at the front of the room. Moving either switch to the opposite position turns the lights off if they are on and on if they are off. Assume the lights have been installed so that when both switches are in the down position, the lights are off. Design a circuit to control the switchesarrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage LearningMicrosoft Visual C#Computer ScienceISBN:9781337102100Author:Joyce, Farrell.Publisher:Cengage Learning,COMPREHENSIVE MICROSOFT OFFICE 365 EXCEComputer ScienceISBN:9780357392676Author:FREUND, StevenPublisher:CENGAGE L
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning
Microsoft Visual C#
Computer Science
ISBN:9781337102100
Author:Joyce, Farrell.
Publisher:Cengage Learning,
COMPREHENSIVE MICROSOFT OFFICE 365 EXCE
Computer Science
ISBN:9780357392676
Author:FREUND, Steven
Publisher:CENGAGE L